Public Works Department Tender

2.5 cm (1") thick 1:2:4 plain cement concrete floor with cement, approved coarse sand and 2 cm. (1") graded approved stone grit, laid in panels finished with 3 mm. (1/8") floating coat of neat cement of cement and marble dust in ratio 5:1 as specified over and including 8 cm (3") thick base concrete consisting of cement, fine sand of 1.25 fineness modulus and brick ballast 4 cm. (1½") gauge in the proportion of 1:4:8 and removing any overlapping mortar at the joints of the penals if any and giving them a uniform finish, including supply of all materials, labour, Tools & plants etc. required for proper completion of the work. (As per S.I. No. 601).

Struck cement pointing with 1:2 cement and fine sand of 1.25 F.M. mortar with colouring including supply of all materials, labour, Tools & plants etc. required for proper completion of the work. (As per S.I. No. 578).

R.R. Stone masonry work in cement mortar 1:3 in foundation complete as drawing and Technical Specification

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 (Grade-M-30), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Provinding and filling Boulder in between second & third wall including supply of all materials and T&P, Labour complete etc.

Providing and laying of boulder apron laid in wire crates made with 4mm dia GI wire conforming to IS: 280 & IS:4826 in 100mm x 100mm mesh (weaved diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 40 kg each.

Providing and laying P.V.C. Pipe 110 mm dia & 6Kg./sqm. (ISI Marked) C/c horizontal and vertical for weephole.

Excavation in foundation in ordinary soil (Loam, clay or sand) including lift upto 1.50 M. and lead upto 30 M. and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in charge upto a distance of 30 M. from the foundation trenches. (where machine can not move) (S.I. No. 251(a)

Providing and laying in cement concrete 1:4:8 (1 cement 4 coarse sand : 8 graded stone ballast 40mm nominal size) and curing complete, including supply of all materials, labour and T&P etc. required for proper completion of the work as per direction of Engineer Incharges.

R.C.C. Work with cement, approved coarse sand & 2 cm gauge approved stone grit in proportions of 1:1.5:3 in lintels of door & windows excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and supply of all materials, labour, Tools & plants etc. required for proper completion of the work including cost of binding wire. The rate excludes making of drip course which shall be paid extra. (S.I. No. 284(A)

Supplying, fitting and placing HYSD bar reinforcement in complete as per drawing and technical specifications