Public Works Department Tender

Providing and applying tack coat with Bitumen VG-10 using bitumen distributor at the rate of 0.30-0.40 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.Chapter-05, Bases an 5.2(i) (Rates are including cost of Bitumen) (For Bituminous Portion)

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case - II By Mechanical Means (I)Bitumen (S-90) Chapter-05 (5.9Case-II(I) (Rates are including cost of Bitumen) (For Bituminous Portion)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 Case - III : Type C (I)Bitumen (S-90) Chapter-05 (5.12 By Mechanical Case-III Type C(i) (Rates are including Cost of Bitumen) (For Bituminous Portion)

Construction of un-reinforced, plain cement concrete avement thickness as per disign, over a prepared sub base with 43 grade cement or any other type as per Clause 1501 2.2 M-30 (Grade), coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 02 cum capacity and appropriate weigh batcher using approved mie design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shove's, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction, expansion, construction and constructionl joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curning of concrete slabs for 14 days. curing compund (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501. (For Mathura) as per SI.No. 13, Ch.No.-20 (For C.C. Portion)

Construction of embankment with Material Obtained from Availble Land Construction of embankment with approved material obtained from availble land as permitted and approved by Engineer-in-Charge and as per Technical Specitaion Clause 301.3.4.1. with all lifts and leads, 1000M spreading. grading to required slope and compacting to meet requirement of Tables 300.1and 300.2 as per Technical Specification clause 301.5 as per SI.No.-19, Ch. No.-20 (For C.C. Portion)

Construction of inaugration foundation platform for 3 feet x 2 feet size granite stone including Excavation, PCC (1:5:10 in fine sand) 7.50cm thick, Brick work in cement mortar (1:4 in course sand), 15mm cement plaster in cement mortar (1:4 in course sand) with finishing walls with water proofing cement paint to or more coat of approved brand & manufacture as per direction of Engineer-in-charge. (For C.C. Portion)

Supply & fixing at site polished granite jet black stone 3 feet x 2 feet size in required design & pattern including engraving & golden painting of letters as per direction of Engineer-in-charge. (For C.C. Portion)

Excavation in foundation in ordinary soil (Loam, Clay or Sand) Including lift upto 1.50 m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer In-charge upto a distance of 30m from the foundation trenches. as per SI.No/DSR-251, Ch. No.-04

Providing and laying cement concrete in 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and curing complete, Including cost of form work. in Foundation and floors. as per SI.No/DSR-4.1.8, Ch. No.-05

Supply & laying of compacted 22.4~53mm Stone Ballast under Hume Pipe

Class-150 (Non Modular) brick work in 1:3 cement and Coarse sand mortar in Foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. as per SI.No/DSR-6.8, CH.-06

12mm Cement plaster with cement mortar in proportion of 1:3 cement & coarse sand of single coat for exterior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm. In girth and finished even and smooth. as per SI/DSR No.13.9.1, Ch.No.-13

Providing and laying of 350mm Hume pipe as per direction of Engineer in charge.

Providing and laying of 1000mm Hume pipe as per direction of Engineer in charge.