Public Works Department Tender

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. As per MoRTH Spec. 1500, 1700 & 2100 Foundation

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. As per MoRTH Spec. 1500, 1700 & 2100 Sub Structure

Furnishing and Placing Reinforced/Prestressed cement Concrete in super-structure as per drawing and Technical Specifications. As per MoRTH Spec. 1500, 1600 & 1700

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications. As per MoRTH Spec. 2706 & 2200

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification

Providing and laying Cement concrete wearing coat M-35 grade including reinforcement complete as per drawing and Technical Specifications. As per MoRTH Spec. 2702

Drainage Spouts complete as per drawing and Technical specification. As per MoRTH Spec. 2705

PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification. As per MoRTH Spec. 2700

Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification. As per MoRTH Spec. 1500, 1600, 1700 & 2704

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications.

Painting on Concrete Surface Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification. As per MoRTH Spec. 1500, 1600, 1700 & 2704

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with a all lifts and leads, transporting to site. Spreading, grading to required slpoe and compacting to meet required of table 300.1 and 300.2 as per Technic

Brick on edge pavement in BOE Soling Road with SOB / class-150 bricks laid dry joints filled with local sand .Rate inclusive of cost of bricks , preparation base of proper slope and its ramming spreading layer of 1.00 cm depth of local sand over the sub-grade including T&P etc. required for proper completion of the work. Rate complete & all inclusive.

Providing and laying of 1000mm dia HPNP4 at site including all labours and materials etc.

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with a all lifts and leads, transporting to site. Spreading, grading to required slpoe and compacting to meet required of table 300.1 and 300.2 as per Technic

Providing, laying and spreading material on a prepared sub grade, adding cement @ 2% by weight to the spread material manually, mixing in place with rotavator and compacting with the road roller at OMC to achieve the desired unconfined compressive strength and to form a layer of sub-base.

Providing, laying and spreading material on a prepared sub base, adding cement @ 4% by weight to the spread material manually, mixing in place with rotavator and compacting with the road roller at OMC to achieve the desired unconfined compressive strength and to form a layer of base.

Providing and applying tack coat with Bitumen VG-10 using Bitumen Pressure Sprayer at the rate of 0.350 kg per sqm on the prepared granular surfaces treated with primer or previously painted surface & cleaned with Hydraulic broom as per MORD Technical Specification Clause 503. and direction of Engineeer in Charge .

Providing, laying and rolling of open-graded premix carpet of 20 mm thick (compacted) composed of 13.2 mm to 5.6 mm aggregates of approved quarry using bitumen (VG-10) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant (Mixol), laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat Type C as per MORD Technical Specification Clause 508 and direction of Engineer-in-charge .

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per MORD Technical Specification Clause 510 and direction of Engineer-in-charge .

Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications

Providing and fixing of reflector Caution and reflector sign / direction board its painting , latter writing and diversion wall etc. Delinator

Supply & fixing of Linear Delineator System (LDS) panels made of Micro Prismatic Retro Reflective sheeting type XI duly laminated on thin aluminium foil to a unique corrugated shape to provide Retro Reflection across wide range of observations and external angles. Eatch LDS panel should be of nominal length of 33 inch and each ridge shall be approximately 0.34 inch high. Each LDS panel is to be firmly fixed on existing concrete/brick work with 16 Nos fastner/ screw

Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810

providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67- 2012 made of high intensity grade sheeting type-IV vide clause 801. 3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of property designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012. Legends, letters numerals and borders etc should be as per MoRTH specification No-801.3.7 Proof of the same in form of government report shall be uploaded while quoting tender. 30X90 cm (Left/Right) Object Hazard

60 mm x 45 mm rectangular with diffinitation plate (20cm X 60cm)