Public Works Department Tender

Construction of granular sub-base by providing close Graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401

Providing laying, spreading and compacting graded stone aggregate to wet mix macadam specification inlcuding premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site laying in uniform layers with mechanical paver in sub-base/base course on wall prepared surface and compacting with vibratory roller to achieve the desired density. As per MOR&TH specification No. 406

Providing, laying, and spreading of Graded stone aggregate (WMM) after mixig with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying including its stabilization with 1% OPC Cement and 3.5% Emulsion in uniform single layer on sub base/ subgrade and compaction with road roller to achieve the desire density.

Providing and applying tack coat with V.G. 10 grade bitumen using emlusion pressure dristributor @ 0.25 kg. per sqm. on the prepared WMM surface cleaned with mechanical broom. As per MORT&H as per Clause 503

Providing and laying Dense Graded Bituminous Macadam with 100-120 tonne per hour capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 Percent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. (Grade-I)

Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.50 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respects. The Rate is Including Labour Cess. (Grade-II)

Providing and applying tack coat with V.G. 10 grade bitumen using emlusion pressure dristributor @ 0.20 kg. per sqm. on the prepared bituminous surface cleaned with mechenical broom. As per MORT&H as per Clause 503

Providing and laying bituminous concrete with 100-120 tonne per hour capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 Percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specificationclause No. 507 complete in all respects (Grade-II)

Earth filling in patri in including rolling with road roller upto required M.D.D., dressing the surface to required level and slope & also including 1.50 m. lift and 30 m. lead, cost of labour, T&P and hire charges of machinery etc. complete work as per direction of Engineer-in-Charge.

Consruction of Rotry & Tringular Island Dismantling of flexible pavements and disposal of dismantled materials upto a lead of 100 m, stacking serviceable and unserviceable materials separately as per Technical Specification Clause 202 As Per Chapter-2 SI No-2.14

Excavation in foundation in B.C soil including lift up to 15 meter and lead upto 30 m (100 ft) and including filling, watering & ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 M from the foundation trenches.(S.I.No. 251)

Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8 Km from the site of work & including watering, dressing etc. Rate to include cost of all materials, labour and tools & plants etc. required for proper completion of the work. (S.I.No. 255)

Cement concrete with 4cm (1/2'') gauge approved stone ballast, approved coarse sand. cement in the proportion 1 : 4 : 8 including supply of all materials,labour and tools and plants etc. required for proper completion of the work. As per S.I. No.-281

R.C.C work with cement aproved coarse sand 2 cm gague aproved stone ballast in the proportion 1:1,5;3 {cement 1.5 coarse sand 3 coarse agg}in lintels of door & windoexcluding suplly of reinforcment and its bending .but including its fixing and blinding the same with 24 B.W.G.G.I binding wire and including necessary centring and shuttring etc.and suplly of all materials ,labours,tools& plant etc required for proper completion of the work binding wire to be supplied by the contractor free of cost. (Slab Work) As Per SI No. 288

Mild steel or iron work of small sizes and sections such as holding down bolts, hold fasts, tierods, gratings, etc. (when not included in over all rates) wrought to required from excluding supply of steel bolts, nuts wastage etc and including their fixing required for proper completion of the work.

Construction of embankment with approved materials obtained from borrow pits with all lifts and leads transpoting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (Lead-4km)

Painting or Vernishing with Valls par or other approved, high graded enamel or superior synthetic clear varnish complete one coat over previously painted surface including supply of all materials, labour and tools and plants etc. completion of the work enamal or varnish to be used should confirm ISI IOS/106/133-1950. As Per A.R.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).10.8

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

One priming coat and two coat oil distemper on new weork including supply of all materials, labour and T&P etc. required for proper completion.of work. AS Per PWD SOR NO. 649

Providing and laying of hot appiled thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC: 35 The finished surface to be level, uniform and free from streak and holes

Supply & Fixing of Pavement maker (Cat eye) Type Z-ASTMD-4956-04 Avery Dennison/3-M (USA MAKE) consisting of ASA plastic housing fitted with tighty adherent ploiting compound. The housing shall contain prismatic two glass covered prismatic reflective face to reflect incident light I/C all tax.

Solar Power road marker (Solar Studs) The solar studs shall be made of Aluminium alloy and poly carbonate material which shall be absolutely Suggestive weather resistant and strong enough to support a load of 13,635 kg tested in accordance with ASTM D4280. Its colour may be white, red, yellow, green or blue or combination as directed by the Engineer Its water resistance shall meet the requirements of IP 65 in accordance with 15:12063:1987 category 2 for protection against water ingress. The dimensions of solar studs shall not be less than 100 mm X 100 mm X 10 mm. It shall have super bright LEDs so as to provide long visibility from a distance of more No than 800 m. Its flashing rate shall not be less than 1 Hz Its should be able to give the prescribed performance in the temperrature range of 40°C to +55°C. Its life shall be not less than 3 Years. The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in-Charge As Per MORTH 804.6 (8.35) - Suggestive

Supply and fixing of retroreflective high intensity informatory sign board/ cautionary sign board etc. As per MoRTH specification. Stop Sign Board

Supply and fixing of retroreflective high intensity informatory sign board/ cautionary sign board etc. As per MoRTH specification. Informatory Sign Board

Supply and erection of direction and place identification retro reflctorised sign as per IRC 67 made of high intensity grade sheeting vede clause 801.30, fixed over aluminium sheeting, 2 mm. thick steel single angle iron post 75 x 75 x 6 mm. firmly fixed to the ground by means of properly designed fondation with M-15 grade cement concrete 45 x45 x 60 mm. 60 cm. below ground level as per approved drawing

Thermoplastic Marking of 300 mm wide and 5 mm height, at 1000 mm apart (one Set is of 6 Strips). 5 mm height is achieved through two applications of thermoplastic, applied at an interval not less than 1 hour after the previous layer gets solidified. (Repeated bars) MORTH-803(8.130)-Base

Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming toIRC-79 and the drawings. MORTH-805(8.150)