Public Works Department Tender

Brick edging on both sides of the road of first brick class M-150. 8 cm wide and 12 cm deep laid with mud mortar including labour & supply of bricks finished to required template and in proper alignment and also including dressing & ramming the excavated earth as directed by the engineer-in charge of the work including material, labour and T & P etc for Proper completion of the work. (Excluding GST)

Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per Technical specification clause - 502

Providing and applying tack coat with bitumen using bitumen VG-10, pressure distributor @ 0.30 Kg/Sqm. on the prepared bitumin surface cleaned with hydralic broom, As per MORD specification 503 (Excluding GST)

Providing, laying and rolling of open - graded premix surfacing of 20 mm compacted thickness with 13.2 mm crushed stone grit @ 0.18cum/10sqm and 11.2 mm size crushed stone grit @ 0.09cum/10sqm from approved quarry and bitumen @ 1.46Kg/sqm to required line, grade and level to serve as wearing course on a previously prepared base, also mixing in a suitable plant or by mixall, laying and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades, including cost of material, labour, plant, machinery and T&P. Complete as per MORD Specification No.508(II) .including the cost of bitumenVG-10, Labour T&P etc.(Excluding GST)

Providing and laying seal coat type-C sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using 6.5 mm crushed stone grit @ 0.09cum/ 10sqm from approved quarry and bitumen/emulsion @0.65kg/sqm including cost of material, labour, plant, machinery, mixall and T&P. Complete as per MORD Specification No.510(ia) including the cost of bitumen VG-10, Labour T&P etc.(Excluding GST)

Construction of un-Reforced, dowel jointed at expension and construction joint only, plain cement concrete pavement, thickness as per desingn, over a prepared sub base, with 43 grade cement or any other type as per clause 1501-2.2 M30 Grade, coarse and fine aggregate conforming to IS 383 macadam size of coarse aggregate not exceeding 25mm mixed in a concretee mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polthene film, wedges, steel plates including leveliing the formwork as per drawing), spreading the concrete with showels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provisiion of contraction and expansion, construction joints, applying, deboinding strips, primer sealant, dowel bars, near approaches to bridge/ culvert and construction joints admixtures as approved, curing of concrete slabs for 14-days curing compound where specifed and water finishing to lines and grade as per drawing and technical specification on clause 1501 (Excluding GST)

Construction of sub grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporting to stite, spreading, grading to required slope and compacted to meet requirement of table no. 300-2 with lead upt 1000m as per Technical specification cluase 303.1 .as per direction of E/I incluidng labour cess,Royalty (Excluding GST)

Earth in excavation in trenches for foudation in ordinary soil including lift upto 1.5 m lead upto 50 m. and dressing of sides and ramming of bottom and disposal of surplus excavated earth as directed by the Engineer-in-charge within a distace of 50m. (Excluding GST)

Plain Cement Concrete M-10 (1:3:6 nominal mix) in levelling cousre below open foundation of head wallas as per drawings and Technical specification clasuse 1109 (PCC grade M 10 (i) Nominal Mix 1:3:6 (Excluding GST)

Brick Masonry work in cement mortar in foundation of Head walls comkplete exculding pointing and plastering as per drawing and technical specification clause 1109(A) Brick masonry in 1:4 cement mortar II. Brick masonry in 1:4 cement mortar (Excluding GST)

Plastering with cement mortar (1:3) 15 mm thick on brickwork in parapet as per technical specifications Clauses 613.4 and 1208.4 (Excluding GST)

Providing concrete for Plain/Reinforced concrete in open foundation complete. As per drawing and technical clause 802, 803, 1202 & 1203IV RCC grade M20 (Excluding GST)

Supply and Laying of 600 mm dia H.P. NP3 Including cartage upto site laying with coller joint filling in cement mortor with Jute, labour T&P etc. (Excluding GST)

Supply and Laying of 350 mm dia H.P. NP3 Including cartage upto site laying with coller joint filling in cement mortor with Jute, labour T&P etc. (Excluding GST)

Supplying, fitting and Placing HYSD bar reinforcement in foundation complete as per drawing and technical specification clauses 1000 and 1202 (Excluding GST)