Public Works Department Tender

Supply & fixing of 100 mm thick Precast cement concrete I -Shap interlocking paver block a with top layer of minimum 8 mm thickness having plan dimension 200x (160+120 mm) of O.P. cement Smooth high glass finish. Skit resistant manufactured from rubber mould through vibro comprision machanism. The compressive strength of concretc paver block shall not be less than 30mpa (M-30) & weight 5 kg per nos of comporming is IS 15658-2006 with a 4 cm thick layer of local sand including cost of material, labour T&P etc. required for proper completion of the work as directed by Engineer-in-Charge as per SOR adi Item No. 5 but excluding GST.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads upto 3 km, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

Cement concrete with 4 cm gauge approved stone ballast coarse sand and cement in proportion of 8:4:1 including supply of all material , labour and T&P etc. required for proper completion of work. As per SI No. 281 )

Chequered Terrazo tiles 22 mm thick with graded marvel chips of size upto 6 mm in flooers, jointed with neat cement slurry mised with pigment to match the shade of tiles including rubbing and polishing etc. Complete on20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) all complete. As per DSR No. 11.19.1 (On top of Divider) Tata Red 445/446

Brick Masonry Work in Cement Mortar 1:3 in substructure complete excluding Pointing and Plastering, as per Drawing and Technical Specifications.

Speed Table (Trapezoidal Hump) Providing and Constructing of Speed Table with Stone set pavement and premix carpet to the required grade, level and alignment, rolling with smooth wheeled roller to achive the desired compaction as per direction E/I.

Cat Eye's Supply & fixing of moulded cats eye shank raised pavement markers made of polycarbonate moulded body and reflected pannel with micro prismatic lens capable of providing total internal reflection of the light entering the lens face conforming to ASTMD for 4280 type 'H' and complying to specification of categories a of MORTH CIRCULAR NO RW/NH/33023/10-07-DO-III 11-06-1997. The height, width and length shall not exceed 20 mm 150 mm and 105 mm and with minimum relfective area of 13 sqcm. and the each side slope to the base shall be 350. Fixing will be without nails but using with twin polymer shanks bitumen adhesive on bitumen roads as per manufacture's recmmendation including site clearence etc. and complete as per direction by E/I.

Solar Power road marker (Solar Studs) The solar studs shall be made of Aluminium alloy and poly carbonate material which shall be absolutely weather resistant and strong enough to support a load of 13,635 kg tested in accordance with ASTM D4280. Its colour may be white, red, yellow, green or blue or combination as directed by the Engineer Its water resistance shall meet the requirements of IP 65 in accordance with IS:12063:1987 category 2 for protection against water ingress. The dimensions of solar studs shall not be less than 100 mm X 100 mm X 10 mm it shall have super bright LEDs so as to provide long visibility from a distance of more than 800 m. Its flashing rate shall not be less than 1 Hz. Its should be able to give the prescribed performance in the temperrature range of -40°C to +55°C. Its life shall be not less than 3 Years. The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all.complete as per direction of the Engineer-in-Charge

Retro-reflectorised Traffic sign as per IRC-67-2012 providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC 67- 2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of property designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International Government Laboratory/ institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012. Legends, letters numerals and borders etc should be as per MoRTH specification No-801.3.7 Proof of the same in form of govemment report shall be uploaded while quoting tender

Speed Limit 60 cm Circular with diffinitation plate (20cm x 60cm)

RAFFIC SIGNS - CAUTION BOARD) 90 cm equilateral traingle with diffinitation plate size (20 cm x 60 cm

CAUTION BOARD - BUS STOP BOARD) 90 cm equilateral traingle with diffinitation plate size (20 cm x 60 cm

ZEBRA CROSSING BOARD) 80 mm x 60 mm rectangular with diffinitation plate (20cm X 60cm)

REPEATED BAR MARKING Providing and laying of hot appiled thermoplastic compound Repeated bar marking 5 mm thick including reflectorising glass beads @ 500 gms per sqm area, Thickness of 5 mm is exclusive of surface applied glass beads as per IRC: 35-2015

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67-2022 made of high intensity grade type IV sheeting vide clause 801.3, fixed cover aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly desinged foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing all complete at site as par E/I (TRAFFIC SIGNS - MAXIMUM SPEED LIMIT) 60 cm Circular with diffinitation plate size (20 cm x 60 cm)

Delinator Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 and the drawings.