Public Works Department Tender

Granular Sub-Base with close Graded Material Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Wet Mix Macadem Providing , laying , spreding and compacting graded stone aggregate to wet mix macadam specification including preixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers with paver in sub base / base couse on well prepared surface and compacting with vibratory roller to achieve the disired density . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

E.T.A. Providing , laying , spreading of graded stone aggregate (WMM) after mixing with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying with 1%OPC cement and 3.50% Emulsion in uniform single layers on sub base / subgrade and compacting with the roller to achieve the disired density. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Tack Coat on Granular surfaces Providing and applying tack first coat with VG.- 10 using bitumen pressure distributor at the rate of 0.20 kg per sqm in the norms bituminous surface cleaned with mechanical broom . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Bituminous Concrete Grading - II Providing and laying bituminous concrete with 120 TPH batch type hot mix plant producing an avarage output of 75 tonne per hour using crushed aggregates of specified grading premixed with bituminous binder @ 5.4 percent of mix and filler , transporting the hot mix to work site , laying with hydostatic paver finisher with sensor control to the required grade , level and aligmnment , rolling with smooth wheeled , vibratory and tendem roller to achieve the desired compaction as per MoRT&H Specification Clause 507 complete in all respects. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of Subgrade and Earthen Shoulders Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 (1.00 Km cartage) (For Patry Work). (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Dismantling Brick- Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the Engineer-in-charge within a distance of 60 meters. (200 feet) As per Sch. PWD-692, Ch.-17. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Dismantling Reinforced Cement- Dismantling reinforced cement concrete or reinforced brick work including stacking of dismantling materials as directed by the Engineer-in-charge within a distance of 60m (200 feet) Sch. PWD-694, Ch.-17 (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert and U Type Drain E/W in excavation intranches for foundation pipes , cble etc. in ordinary sil ( lomy clay or sand) incluidng lift upto 1.50 m lead upto 30m and dressing of sides and ramming of bottom and disposal of surplus excavated earth as irected by the E/I eithin a lead of 30M .(Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert and U Type Drain Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. .(Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert Brick masonry work Brick masonry work in cement mortar 1:3 for Super Structure complete as per drawing and Technical Specifications. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert Brick masonry work Brick masonry work in cement mortar 1:4 for Foundation complete as per drawing and Technical Specifications. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert R.C.C. in M25 R.C.C. in M25 with 1 part of cement 1.50 part coarse sand and 3 part of 20 mm gauge hard stone grit in slab and bed block including all taxes , royalty but excluding cost of steel including supply of all materials , labour , T&P and etc. required for proper completion of the work as per direction of E/I. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of U Type Drain Only R.C.C. in M20 Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert and U Type Drain M.S iron work in plain work such as in reinforcement cement concrit including wrought to required shape & section including bending and binding including supply of steel its wastage , bind hook authorized over lapping shall be measured and including supply of all martial , labour T&P etc. required for proper completion of the work as per direction of E/I. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert Providing and laying weep holes in stone masonry abutment , wing wall, retaining wall with 10 cm dia PVC pipe entering through the full with of the surface with slope of 1 (V) :20(H) ( including S/O all materials , labour T&P and etc. required for proper completion of work as per direction of E/I. (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert Struct cement pointing with 1:3 cement and course sand including all taxes ,royalty , and including supply of all martial , labour T&P etc required for proper completion of work as per direction of E/I . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert 12mm thick cement plaster in 1:4 cement and course sand mortar including all taxes , royalty and including supply of all material , labour , T&P etc. required for proper completion of work as per direction of E/I . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert Providing and laying Filter media with granular crushed aggregate as per specification to a thickness of not less then 60 cm with small size lowers the bigger size towers the wall and providing entire surface behind abutment , wing wall , return wall to the full height completed to firm condition complete including all materials , labour , T&P and etc. required for proper completion of the work as per direction of E/I . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert R.C.C. in M25 Earth Work in Filling in embankment for Diversion and approach road work in soil mixed with Kanker / Single / Black Cotton soil including all lead lift , including ramming dressing and including S/O all materials , labour , T&P etc. required for proper completion of the work as per E/I . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Construction of 1x2 and 1x3 m. span RCC Culvert R.C.C. in M25 Dewatering of foundation , trenches by 8 HP diesel operator pumps including all labour , materials , T&P etc. complete work ( Taking unit 1 Hrs per Pumps ) . (Rates are Including Royalty, Labour cess and other Taxes but excluding GST.).

Over head sinage Supply & Erection of built up overhead structure 12.00 M to 15.00M span comprising of three vertical post of 6.00 M high made up of 300 mm N.B. havey class M.S. pipe as vertical member welded with 10mm M.S. plate at top & bottom for bearing of horizantal frame comprising of 40 mm . N.B. made havey class main pipe as of 25 mm class medium N.B. pipe bracing as per approved designed drawing with one coat of steel primer and two coats of synthetic enamle paint complate the work includes construction of RCC fundation of size 0.75x0.75M & 1.2 M deep for built up Overhead Structure including earth work in excavation , 100 mm thick Lean Concrete in 1:4:8 cement , course sand and 40 mm gauge stone balllast , RCC with 1:2:4 cement , Course sand and 20 mm stone grit including supply of grouting of 25 mm dia foundation bolts (600mm long) as per provision of structure including cost of reinforcement & shutting as per direction of Engineer in Charge (Including All taxes, labour cess, T&P and Material but excluding GST.).

Informatory Board Providing and fixing of reflective signs with a corrosion resistsnt 4 mm thick aluminium complete panel face to fully covered with high intensity prismatic sheeting type -iv AS PER IRC-67-2010 Retro reflective sheeting with MS angle frame of 35x3. (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Triangular Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Stop Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Hazard Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Circular Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Chevran Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Abadi Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Caution Board (Railway Board) Providing and erecting direction and place identification retro reflectorized sign as per IRC-67 made of high intensity grade sheeting vide clause 800.1 fixed over aluminium sheeting 2 mm thick over area not exceeding 0.9 sqm supported on mild steel angle iron post 75x75x6 mm firmly fixed to the arround by means of properly designed foundation with M15 grade cement concrete 45x45x60 mm below ground level as per approved drawing complete 90x90 cm . (Including All taxes, labour cess, T&P and Material but excluding GST.).

Retro-Reflective sheeting type IV with 4 mm thick ACM double side Providing and fixing of reflective signs with a corrosion resistsnt 4 mm thick with 0.4 to 0.5 mm both side aluminium complete panel face to fully covered with high intensity prismatic sheeting type -iv AS PER IRC-67-2010 Retro reflective sheeting with MS angle frame of 35x35x3 back frame etc all completea As MORTH 801 Specification.. (Including All taxes, labour cess, T&P and Material but excluding GST.).

Thermoplastic painting Providing and laying of hot applied thermo plastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area thickness of 2.5 mm is exclusive of surface applied glass bed as perIRC 35 inclduing cost of all materials , labour , Machinaries , T&P etc. requared for peoper completion of work i/c all other charges and taxes . The finishied surface to be level uniform and free from streks and holes as per MORTH specification no. 803. (Including All taxes, labour cess, T&P and Material but excluding GST.).

Delineators Supplying and installation of delinators (road way indicators, hazard markers, object marker) 80-100 cm high above ground lavel , panted balck and white in 15 cm wide strips fitting with 80x100 mm rectangular or 75mm dia circular reflactorised panal at the top buried or pressed into the ground and conforming to IRC:79 and the drawing. (Including All taxes, labour cess, T&P and Material but excluding GST.).

Reflective Raised Pavement Markers (Road Studs / Cat Eye) Supply and fixing of reflective raised pavement marker with its body surface made of tough ASA (Acrylic styrene Acrylonitrite) or HIPS ( impact Polystyrene) or acrylonitrile butadiens styrenc (ABS) The marker shall supported a load of 1335 kg tested in accordance with ASTMD 4280 and its reflective panels shall consist of number of lenses containing single or dual prismatic cubes of providing total internal reflection of the light entering the lens face. Retro reflecting surface shall preferably be 351 5° to base and area of each retro-reflecting surface shall not be less than 130 sqcm road studs shall be legibly marked with name trade mark or other means of identification of the manufacturer Dimensions of road studs should not be less than 100 mm x 100mm x10mm.(Including All taxes, labour cess, T&P and Material but excluding GST.).

Accident prone zone board Providing and fixing retro-reflective signboards comprising of customised modular PU Epoxy Coated MS angle iron frame work, almunium composite panel (ACP) as base board micro prismatic retro-reflective sheet and electro cul coloured overlay film latex printing The horizontal and vertical members including inclined outer members of the MS frame module shall be made of pair MS angle iron. No panel size shal be more than one Sqm and each panel shall be braced diagonally (one way only) with MS angle The MS frame module shall have length not more than 3 mtr. The aluminum.composite panel (ACP) shall have a thickness of 4mm with 0.5mm thick skin of aluminium on both sides The ACP shall be fixed on the MS frame with pop niveting or with self taping SS screws 5mm dia spaced not more than 300mm centre to centre ensuring that no riveting is seen on either face of the frame On the front So visible face of the ACP, micro prismatic retro-reflective sheet conforming to Type-IV of ASTM D 4956-09 shall be pressure fixed. The retro reflective sheeting shall be tested for 3 year outdoor weathering test in Indian conditions as per IRC 67 2012 & proof of the same in form of government report shall be uploaded while quoting tender. The rate shall include all materials, labour, equipments, fabrication, transportation erection, installation and incidentals all complete as per direction of the Engineer-in- Charge Signage on MS angle frame of (35x35x5)mm.(Including All taxes, labour cess, T&P and Material but excluding GST.).

Rumble Strips Provision of 15 nos. rumble strips coverd with primix bituminous carpet, 5 mm height at center, 250 mm wide placed at 1 m center to center at approved locations to control speed, marked with white strips of road marking paint..(Including All taxes, labour cess, T&P and Material but excluding GST.).

Repeated Bar Providing and laying of hot appiled thermoplastic compound 5 mm thick including reflectorising glass beads @ 250 gms per sqm area, Thickness of 5 mm is exclusive of surface applied glass beads as per IRC: 35 The finished surface to be level, uniform and free from streak and holes For bar marking at Main Road .(Including All taxes, labour cess, T&P and Material but excluding GST.).

Crash Barriers Providing and erecting a "W" metal beam crash barmer comprising of 3 mm thick corrugated sheet metal beam ral, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 18 m high, 1.1 m below ground'road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS 1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm 330 mm long complete as per clause 810 .(Including All taxes, labour cess, T&P and Material but excluding GST.).

Tree Plate S/F Reflective tree Plate having Size 15 Cm x 15 Cm, Consisting type -XI sherting over 1.5 mm thick aluminium sheet including labour, material T&P ete for proper completion of the work .(Including All taxes, labour cess, T&P and Material but excluding GST.).