Prayagraj Smart City Limited Tender

Cement concrte with 40 mm gauge approved stone ballast, coarse sand and cement in proportion of 8:4:1 including supply of all material, labour, tools & plant etc required for proper completion of work. Excluding GST

R.C.C. work with cement approved coarse sand and 2 cm. Gauge approved stone grit in proportion of 1 : 1.5 :3 in raft foundation & footing excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W. G.G.I. Binding wire and including necessary centering and shuttering etc. and supply of all materials, labour, T & P etc. required for proper completion of the work including cost of binding wire. Excluding GST (SoR 287 A /2022)

40 mm thick fine dressed red sand stone flooring (size of red sand stone slab should not be less than 500mm x 500mm) over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone.(flooring pattern should be as per design and as directed by Engineer in Charge)

S/F of Smart City branding signage Made of stainless steel plate of size 750X300 mm, 2 mm Gauge including Letters engraved 1 mm deep & painted in the sheet fixed with 2 numbers of 1 m height CP pole of 50 mm dia and fixed with cement concrete as per design and drawing complete in all respect as directed by engineer in charge.

Supplying and Fixing of Red stone bench having thickness of top slab not less than 3" fitted with Stone rectangle block of size not less than 30x30 Cms at both ends. Length of Bench should not be less than 6 ft (end to end support).width of bench 2 feet and height 1.75 feet as per design and drawing complete in all respect as directed by engineer in charge.

Pull Chair (Double)- Providing and fixing pull chair in a pair with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1950 x 700 x 2000 mm 2. Fabricated with main post of NB100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80- 120 micron thick Akzo Nobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.

Chest Press (Double) - Providing and fixing chest press in a pair with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1800 x 700 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Standing Waist Trainer- Providing and fixing Standing Waist Trainer with below dimensions: With five year Maintenance 1. Dimensions (LxWxH): 2000 x 700 x 1700 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65 mm (G.I.) ‘C’ Class Pipe 4. Handle frame support of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. Foothold plate of made of cast iron of 12mm thickness. 6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with cement concrete and Expansion Bolts. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless steel label fixed on equipment for ease of use

Space walker- Providing and fixing Space walker with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1100 x 550 x 1480mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. ‘U’ shaped main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. All other pipes of NB 32mm (G.I.) ‘C’ Class (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Bicycle-Providing and fixing Bicycle with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1000 x 600 x 1100 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7.Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 25mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Leg Press (Double)- Providing and fixing leg press in a pair with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1750 x 550 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Shoulder Wheel (Double)- Providing and fixing Shoulder Wheel in a pair with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 850 x 800 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I. ‘C’ Class Pipe of approved make. 3. Main frame wheel of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and selflubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 12. High tensile steel with galvanized nut bolts are used for assembly.

Parallel Bar- Providing and fixing parallel bar with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 2500 X 800 X 1500 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 8. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 9. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 10. High tensile steel with galvanized nut bolts are used for assembly. 11. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 12. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Rowing Machine - Providing and fixing rowing machine with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1280 x 800 x 1150 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 65mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11.Maintenance free bearings of SKF or equivalent make duly oil sealed and self lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Chin-up and Dipping Bars- Providing and fixing Chin-up and Dipping Bars with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 3500 X 800 X 2500 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 8. The equipment is fixed on ground with cement concrete and J shaped welded bolts of 18mm thickness. 9. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 10. High tensile steel with galvanized nut bolts are used for assembly. 11. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 12. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Scaling Ladder- Providing and fixing Scaling Ladder with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 2900 X 1050 X 2200 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 80 mm (G.I.) ‘C’ Class Pipe. 4. Side pipe 65 mm with parallel pipe 40 mm 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. The equipment is fixed on ground with concrete and J shaped welded bolts of 18mm thickness. 10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment must comply to EN16630 / DIN79000 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Sit Up Bench- Providing and fixing double sit-up Benches with below specifications: With five year Maintenance 1. Dimensions (LxWxH): 1500 x 1150 x 650mm 2. Fabricated with base frame of NB 50mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. 4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness. 6. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. 7.All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all welding points prior to finishing. 9. The equipment to be fixed on ground with concrete and Expansion Bolts. 10. Once the concrete is set, the equipment is fixed on to it. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment must comply to EN16630/ DIN79000 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use.