North Central Railway Tender

Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar.App. Cases inside and outside to be done by Silver colour. (Apparatus Case Half)(Inspection agency :- Consignee)

Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar. (Main Signal post, base, unit and complete fittings)(Inspection agency :- Consignee)

Painting of two coats of Enamel paint over one coat of Red Oxide primer after scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar. (Shunt Signal post, base, unit and complete fittings)(Inspection agency :- Consignee)

Lettering/numbering of Track lead junction box(it include writing work ), track lead junction boxes, 07 block joints (it include writing on both side of rail of Block joint ), (Each item to be taken as one unit). The work shall be done as per extent practice on N C Railway and the instructions of Railway representative at site. Paints to be used by contractor should be h of Asian/Berger Paints make.(Inspection agency :- Consignee)

Maintenence of Signalling gears required for excecution of BCM/TTM/FRM or any other signalling work which includes: (1) Proper dressing of track lead jumpers as required by the Railways before and after 08 BCM/TTM/FRM machine working. (2) All cables attended during work to be meggared and all damaged cables due to work to be replaced as per requirement of Railways (3) Preparatory work required for the work of Point renewal, removing, fixing, installation and testing of rodding set for point machine including all associated gears of mechanical/electrical points as per direction of Railway representative at site. (4) Any other s decided by Railways. The team to be provided for this work should comprise of: Fitter-1 no., Blacksmith- 1 no., Carpenter/Mason- 1 no. and Helpers- 5 no. (Day = per day per team).(Inspection agency :- Consignee)

Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes 09 etc. as per the site requirement and as per approved cable route plan. This also includes laying of cables in track crossings & road crossings.(Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes.(Inspection agency :- Consignee)

Laying of Double Wall Corrugated (DWC) pipe of all sizes with socket, coupler and T Joint etc. by 10 digging of trench 0.3 Meter width, 1.2 Meter depth from rail flange under track for track crossing and refilling after laying of pipes, as per technical specifications and the restoration of disturbed ballast by screening and dressing as per instruction of Engineer-in- charge or his representatives at site.(Inspection agency :- Consignee)

Horizontal Boring/Manual moling without damage to surface road /track for laying/isertion of DWC/GI/HDPE pipe. The bore shall be done at the depth of minimum 1400 mm from the ground level. The 11 ground level shall be considered ignoring the bank height of the bank of the road. Note:- DWC/HDPE/GI Pipe Supply is not covered under this item. Contactor shall provide all material required for work and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. Payment of boring shall be made only after DWC/HDPE/GI pipe is laid in the bore. (Inspection agency :- Consignee)

Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003, issued vide RDSO document no. RDSO/SI/G/2010 Version 1.1 dated 04.02.2014 or latest, alongside the track in normal soil/strata (including soft rock), conforming to distances as per cable route plan and refilling and ramming of loose soil. This work includes clearing of route 12 from bushes etc, covering of cable laid in trench by loose soil for a layer of 50mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Central Railway and instructions of Railway Engineer at site. In case the full depth is not available, there shall be no proportionate payment and after the approval of minimum JAG officer, the concreting shall be done as per the RDSO drawing no.SDO / Cable laying/ 008, issued vide RDSO document no. RDSO / SI / G / 2010 Version 1.1 dated 04.02.2014 or latest. (Inspection agency :- Consignee)

Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003, issued vide RDSO document no. RDSO/SI/G/2010 Version 1.1 dated 04.02.2014 or latest, alongside the track in Rocky soil, conforming to distances as per cable route plan and refilling and ramming of loose soil. This work includes clearing of route from bushes etc, covering 13 of cable laid in trench by loose soil for a layer of 50mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Central Railway and instructions of Railway Engineer at site. In case the full depth is not available, there shall be no proportionate payment and after the approval of minimum JAG officer, the concreting shall be done as per the RDSO drawing no.SDO/Cable laying/008, issued vide RDSO document no. RDSO / SI / G/2010 Version 1.1 dated 04.02.2014 or latest. (Inspection agency :- Consignee)

Cement concrete work for miscellaneous, unscheduled items in ratio 1:3:6 of cement, coarse, sand 14 and aggregate Item includes excavation, ramming of CC by using vibrator, curing and plastering with cement and sand mixture in ratio 1:4 (aggregate will not exceed beyond 3.8 cm). The aggregate cement and sand will be supplied by contractor.(Inspection agency :- Consignee)

Prepration and soldering of cable 1 to 30 core and quad for earthing ( both side earthing to be done)(per cable)(Inspection agency :- Consignee)