New Okhla Industrial Development Authority Tender

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : "1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Centring and shuttering i/c strutting, propping etc. and removal of form for Foundation, footings, bases of columns etc. for mass concrete.

Centring and shuttering i/c strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Cold twisted bars

P/F M.S. specials such as Tee, Bend, Collars, Tapers, Gap pieces, including Flange Ends as required, Painting, Cutting, welding as per site requirement of MS pipe thickness etc complete in all respect as per direction of E/I.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming & watering, lead upto 50 m and lift upto 1.5 m.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Supply and installation of required size Steel pipe 8 mm thick conferming to IS:3589 through trenchless excavation of thrust pit and receiving pit of required size and the excavation & filling back and compaction complete as per specification for road crossing by Auger boring method. Pipe will be installed at depth beyond 3.0 m. below the ground surface in downward required slope. : 200 mm dia 8 mm thikckness

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

P/F 250 mm dia Sluice Valve shall generally conform to IS 14846 with latest amendment, with length over flanged as per PD of IS 14846 corresponding to BS EN-558 / ISO 5752 Basic series 3 in CI construction having metal seating (IS 318 Gr. LTB 2). With comple component & material of construction following below:- 1 - Body / Door / Dome - Cast Iron IS 210 Gr. FC 260 2 - Spindle - Non rising: Stainless Steel AISI 410 3 - Body seat / Door face - Gun metal : IS 318 Gr. LTB 2 (rings to be press fitted and riveted: no screws allowed) 4 - Rivets - Soft annealed brass 5 - Spindle Nut - Gun metal : IS 318 Gr. LTB 2 6 - Stem Seal - Greased Hemp 7 - Fasteners - Carbon steel 8 - Flange Drilling - IS 1538 Table 4 & 6 9 - PN 1.0 10 - Accessories (400 mm and above) - Ball thrust bearings to be housed above the wet chamber ie. above the gland. Enclosed Spur Gear Box for ease of operation. Air Plug 11 - Painting / Coating - Inside & Outside epoxy liquid coated; DFT minimum 250 micron, shade RAL 5005 / 5015 (BLUE) 12 - Hydro-test-(Open Ended only) (Seat : 10/16 Kg/cm2; Body: 15 / 24 Kg/cm2 13 - Upto 600mm dia Mannual Operated & above 600mm Gear box Make-Indian Valve Pvt. Ltd. (IVC) / Kirloskar Brothers Limited KIRLOSKAR)

P/F 250 mm dia Reflex Valve upto 600mm dia shall conform to IS 5312 Part-1 & above to IS 5312 Part-2 with latest amendment, Valves shall be in graded CI with metal to metal (IS 318 Gr. LTB 2) seating, preferably slanted (and not perpendicular) vis-a-vis horizontal axis; SS AISI 410 stub pins & slant seat design. with comple component & material of construction following below:- 1 - Body / Door / Dome - Cast Iron IS 210 Gr. FC 260 2 - Hinge pin (single door) / Stub pin (multidoor type) - SS AISI 410 3 - Seat & Face rings - Gun metal : IS 318 Gr. LTB 2 4 - Rivets - Soft annealed brass 5 - Fasteners - Carbon steel 6 - Flange Drilling - IS 1538 Table 4 & 6 7 - PN 1.0 8 - By - pass arrangement - Optional 9 - Painting / Coating - Inside & Outside epoxy liquid coated; DFT minimum 250 micron, shade RAL 5005 / 5015 (BLUE) 10 - Hydro-test Seat : Seat : 10/16 Kg/cm2; Body: 15 / 24 Kg/cm2 Make-Indian Valve Pvt. Ltd. (IVC) / Kirloskar Brothers Limited KIRLOSKAR)

Supply, erection, testing and commissioning of non clog sewage submersible pump complete in all respect as per direction of engineer in-charge. Technical specification of pump set shall be as given below. (1) MOTOR TYPE: Sq. Cage induction motor 960 rpm suitable for operation on 400/440 volts 3 phase, 50 hz ac supply with f class insulation & ip68 protection. 2) PUMP: (a) Body: - cast iron with 2% nickel (b) Impeller:- CF8M (SSJ16) (c) Shaft:- Stainless Steel (SS304) (d) Auto coupling stand:- CF8M (SS316) (e) Guide pipe:- stainless steel (SS304) @16 mtr (f) Lifting chain:- alloy steel @16 mtr (g) Mechanical seal:- Upper seal (carbon/chrome steel). Lower seal (silicon carbide). (3) FIELD REQUIREMENT: (a) Type:-non clog sewage submersible pump (b) RPM:- 960 (d) Head:- 28 mtr (e) Copper cable for sewage submersible pump suitable size @ 25 mtr (f) Specific gravity of sewage: - 1.07 (g) Solid Handling Capacity (dia):- not less than 100 mm NOTE- contractor shall be submitted G.T.P & all company test certificate of the material used in pump set. (make- pullen pump industries pvt ltd / m/s aqua machineries pvt. Ltd. /m/s kishor pumps pvt. Ltd.) Non Clog Sewage Submersible Pump Set Discharge 432 cum/hr., HEAD :- 28Mtr., Rating 60/80, Outlet size of pipe 200mm dia, Cable 2 x 50 sqmm x 3.50 core + 1.50 sqmm x 4.0 core

S/F of fully Automatic Control panel with 100 H.P. Auto Transformer for submersible/V.T. Pump sets with following features No-volt, Under-voltage, Over-voltage protection, Microprocessor based overload protection, Unbalancing protection, Winding temperature controller, seal monitor, reverse rotation trip device and the automatic start/stop device according to the levels in the sump. The control panels are provided with normal indications such as Digital voltmeter, Digital Ammeter, and indicating lamps. Above panel is dust and vermin proof made out of 14 SWG CRC sheet with powder coating paint as per directions of E/I. (Make: Contractor-L &T, MCCB-L&T, WTC-Minilec, Auto Transformer-Electracare, VPD & MPD-Softhard, WLC/SM-Pumpcare C.T.-AE, Indicating Light & Push Button- L&T, Control Fuse-EE, Fuse Base-EE, Timer-L&T)

Supply and Fixing of LED Street light fitting having die cast aluminium body and diffuser with driver set suitable for 60 to 72 watt. Confirming to IP 66 protection complete in all respects.

Submersible Cable moter capacity 75 HP to 120 HP (2 x (35sqmm x 4 core) +1 x 1.5 sqmm 4 core)

S/F of 200 Amp. four pole change over switch on 50x50x6mm angle iron frame i/c the cost of labour, T&P, painting and other material requried for proper completion of the work as per direction and satisfaction of E/I.

S/L of aluminium conductor PVC insulated armoured served, sheathed cable 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on MS clamps etc. of suitable size or as directed by Engineer-Incharge complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.: 120 sqmm 3½ core

Supply & Fixing Flat Cable 35 Sqmm. 3 Core Finolex make.

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Brick work with F.P.S. bricks of class designation 100 in foundation and plinth in cement mortar 1:4 (1 Cement : 4 C. Sand).

P/L following size of Finolex makes PVC pipes 6 Kg/Cm2 with required PVC standard special confirming to IS codes with latest amendment and lowering the same trenches and laying true to alignment and gradient complete i/c the cost of cutting of pipes for making up to length and making joints i/c cost of socket, plstochem PV-85 pvc solvent cement complete. PVC pipe must be confirming to IS:4985-2000 with latest amendment. Make-Finolex Industries Ltd./Kisan/Superme Industries Ltd. (Rate As per Comparative Statement Per. Rm.) 25.01) 90 mm dia with coupler @ 6 Kg/Cm2 Pressure with i/c all PVC standard Specials

110 mm dia with coupler @ 6 Kg/Cm2 Pressure with i/c all PVC standard Specials

140 mm dia with coupler @ 6 Kg/Cm2 Pressure with i/c all PVC standard Specials

160 mm dia with coupler @ 6 Kg/Cm2 Pressure with i/c all PVC standard Specials

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 300 mm dia

S/F Submersible motor pump CRI Make : 5 HP

Supply & Fixing Flat Cable 6 Sqmm. 3 Core Finolex make.

Supply, Lowering & Showing the annular space between Tube Well bore and assembly with 2mm to 5mm thick Pea gravel.