Moradabad Development Authority Tender

Distempring two coat with oil bound distemper of approved brand and manufacture and required shade on undecorated wall surface with an even shade over and including a primer coat with cement primer of approved brand and manufacture such as of British, 'Shalimar asian paint after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand prepared smooth including cost of all materials. SI. No-649+650/2022

R.C.C. Work with cement approved coarse sand and 2cm. gauge approved stone grit in proportion of 1:1/2:3 in slabe excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I Binding wire and including necessary centering and shuttering etc. and supply of all meterials, labour and T&P etc. required for proper completion of work. Binding wire to be supplied by the contractor free of cost. lncludinq makinq of drip coarse. SI No-284 (a)/2022

Mild steel or TMT Bars (Fe-500 D grade or higher) or HYSD Bars or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) brought to required shape as necessary including bending for proper completion of the work and including supply of all steel. SI No-504/2022

S/F of 10cm dia of PVC down pipe complete with rose head bends M.S. clamps 2.5 cm X 3 cm X 3 mm fixed to walls by 15 cm long 6 mm dia nall including repairing of plaster, pointing ect. Including suppy of all materials labor T&P ect. Required for proper comletion of the work PWD SI no.730(a)/2020

M-150 brick work in Superstructure 1:4 (one cement and four coarse sand) including necessary cutting and moulding of brick and rewuried thickness of walls not to be less than 1.0 brick. SI 307+309+310/2022

Mild steel or iron work in heavy sizes such as trusses; built up gates, door, frames, record racks, roof work, gates etc. wrought to required form including drilling holes, rivetting or welding where necessary, and also including supply of steel, bolts and nuts. SI No-503)/2022

Supply and fixing of 32mm thick flush door commercial quality conforming to I.S. 2022 Part I (1983) including fixing of wooden clears and stoppers and including fixing and adjustment of hinges bolts locks handles springs fitting with necessary screws to be supplied. SI No-470/2022

Painting two coat over priming coat (including cost of priming coat) on steel and other metal surface with superior synthetic enamel paint of standared make brushing to give an even shade and finished and including cleaning the surface all dirt dust and other foreign matter sand paparing and stripping including cost matter and scoured with wire brushes fine steel/ wood scrappers sand papering and knotting including coat of all and supply of all materials, labour and T&P etc. required for proper completion of the work. New Item No- 1(a)+2+4(iii)/2022

Painting two coat over priming coat (including cost of priming coat) on wood surface with superior synthetic enamel paint of standared make brushing to give an even shade and finished and including cleaning the surface all dirt dust and other foreign matter sand paparing and stripping including cost matter and scoured with wire brushes fine steel/ wood scrappers sand papering and knotting including coat of all and supply of all materials, labour and T&P etc. required for proper completion of the work. New Item No- 1(b)+2+4(iii)/2022

2.5cm thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm Graded approved stone grit laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and including 8cm thick base concrete consisting of cement fine sand of 1.25 fineness modulus and brick ballast 4cm gauge in the proportion of 1:4:8 and removing any over lapping mortar and the joints of the panels if any and giving then uniform finishing including supply of all materials, labour and T&P etc. required for proper 2.5cm thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm Graded approved stone grit laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified over and including 8cm thick base concrete consisting of cement fine sand of 1.25 fineness modulus and brick ballast 4cm gauge in the proportion of 1:4:8 and removing any over lapping mortar and the joints of the panels if any and giving then uniform finishing including supply of all materials, labour and T&P etc. required for proper completion of the work. completion of the work.SI no-601 Same as above

Same a Above Item no.11 but without base concrete but 4 cm thick instead of 2.5 cm thick SI No-605

10cm thick average mud phuska of damped mud mixed with chopped straw @ 8 to 10kg. Per cum well preported 5cm mud laid to proper slope consolidated with wooden thappies with and including 13mm thick plaster with mud and gobri mortar in proportion 3:1 mud and cow dung and covered with flat brick tiles 4 cm thick designated M-100 grouted with cement and fine sand nortar in 1:3 the joints shall be finished with the brick tile surfaceincluding cost of all materials, labour and T&P etc. required for proper completion of the work including pointing in proportion of 1:2 (1 part of cement and 2 parts of coarse sand) (New Item, Ch.-11, P-33 /2022) New Item-1

Providing gola 75X75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse snad : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design DSR No 12.21.1/2021

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m X 1m X 400 micron, finished with 12mm cement plaster 1:3 cement and coarse sand and a coat of neat cement all complete . DSR No-12.22/21

Providing and placing on terrace (at all floor levels} polyethylene water storage tank ISi: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. SOR- 2021/18.48

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (20mm) DSR-2021/18.7.2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (40mm) DSR-2021/18.7.5

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore DSR-2021/18.17.1A

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore DSR-2021/18.18.2

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore DSR-2021/18.13.1

20mm thick rough cast exterior cement plaster on walls consisting 10 mm thick backing cast of 1:3 cement mortar (1 cement :3 coarse sand) and 10 mm thick finishing coat of 1:3 cement mortar (1 cement :3 coarse aggregate of size 6mm to 12mm) including arises, chamfers and/or rounded angles not exceeding 80 mm. SOR-2022/CH-13 New Item no-1 Page -37

Supply and fixing of swich box made up 16SWG (1.5mm) thick M S Sheet of different size dully painted with red oxide primer & flused in wall including cutting of brick work fixing it to the level with cement sand mortar including maching colour wash with S/o all material labour & T&P required for proper completIon of work as directed at site by the Engineer in Charge (SOR No 159/2016 (i) 100x100A5 mm (159/2018)

(ii) 175x100x65 mm (SOR No 161)/2018

(iii) 200x250x65 (162/2018)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. DSR-8.31/2021

Providing and fixing 610mmx450mmx250mm size stainless steel sink 1mm hick of heavy as aprroved by Engg. In- charge including waste ali including supply of all materials labour T&P etc. required for proper completion of the work and including cutting and making good etc all complete. DSR-2021/17.10.2.2

Supply and fixing of 3.8 to 4.7 mm thick glass panes of ISI approved quality with equal or equivalent ISI marks .brads and putty and springs for window and ventilator m.s section of wherever is required on other places including cartage of all items (PWD New Item 2(b)Ch-19)

S/L OF PVC CONDUIT COMPLETE WITH BEND 25MM DIA.SI 149(A) SOR-2018

Providing and fixing glass strips of 3.15mm thick and 2.2cm depth in joints of floors and skirting or dado add the time of laying floors flush with floor level including supply of all materials, labour and T&P etc. required for proper completion of the work. SI. no-631(a)/2022