Moradabad Development Authority Tender

12 mm. thick plaster with 1:4 (one part cement &Four parts of coarse sand of 2.75 F.M. ) over brick work minimum thickness Including supply of all material , labour, T & P etc. required for proper completion of the work. ( S.I.No.584 )2020

Distempring two coat with oil bound distemper of approved brand and manufacter and required shade on undecorated wall surface to with an even shade over and inculiding a primar coat with cemant primar of approved breand and manufactuer such as of britsh Shalimar asian paint after throughtly burshing the surface free from mortar dropping and other froegn matter and also inculiding preparing the surface even and sand prepared smooth inculding coat of all materials.SI 649+650/ 2020

Providing and fixing white vetreous china pedestal type water coset (European type) with seal and lid 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fitting & C.I. brackets, 40mm flush bend, overflow arrangement with spcloset squatting pan (Indian type W.C. pan) with 100mm sand cast iron P or strap, 10 litre low level white P.V.C. flushing cisttemwith manually controlled device (handle level) conforming to IS: 7231. with all fitting and fi. PWD SOR 17.3 CH-22 /2020

25 mm thick Cement concrete flooring 1:2:4 (1cement : 2coarse sand : 4graded stone aggregate of size 20 mm nominal size )laide in one layer , finished with floating coat of neat cement.including fixing of glass strips. (excluding cost of glass strips ). item no.SOR 601A

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) DSR N0 21.1.1.1/2019

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC DSR N0 21.1.2.1

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weithing not less than 810gms. 15mm nominal bore. PWD SOR 18.50.1 CH-22 /2019

Supply and fixing 6mm china white glazed tiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry joining and polishing complete including supply of all materials, labour T& P etc. required for proper completion of the work. S.I. 628/2019

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC slovent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer - in - charge. Concealed work including cutting chases and making good the walls etc. (DSR- 18.8.1)/2018

(i) 15 mm (18.8.1)

(ii) 20 mm (18.8.2)