Ministry Of Road Transport And Highways Tender

Painting roofs or other iron work in large area with one coat of ready mixed paint primer paint and two coat approved paint (British, ANISOLE or Equivalent )including supply of all material , labour and T&P etc.Required for proper completionof the work. Pain to be used should confirm the I.S.I. No. 103-1950 cost for area 650 Sqf priming coat.

Retro reflective Sticker (3M)for barrier optimal brightness and Safety (Size 2x4 inch) Colour Red/yellow

Providing and laying centre line / edge line marking with hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

ROAD STUDS/ CAT EYE - S/F of reflective raised Pavement Maker with its body surface made of tough ASA (Acrylic styrene Acrylonitrite) or HIPS (Hi impact polystyrene) or acrylonitrile butadiens styrenc (ABS). The marker shall supported a load of 1335 kg tested in accordance with ASTMD 4280 and its reflective panels shall consist of number of lenses containing single or dual prismatic cubes of providing total internal reflection of the light entering the lens face retro reflecting surface shall be less then 13.0sqcm road studs shall be legibly marked with name trade mark or other means of identification of the manufacturer. dimensions of road studs should not be less then 100mm x100mm x10mm. (RPM (with shanks) as per ASTM) at Bridge.

Providing and fixing of retro reflectorised cautionary, mandatory and informatory sign as per IRC 67-2012 made of high intensity grade sheeting vide clause 801.3, friced over aluminium sheeting type -iv 105 mm thick supported on a mild steel angle iron post 75mm x75mm x6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45cm x45cm x60cm , 60cm below ground level as per approved drawing. the retro reflective sheeting shall be tested for 3 year out door weathering test indian conditions as per IRC 67:2012 & proof of the same in form of government report shall be uploaded while quoting tender.30x90cm (Left/Right) Object Hazard at bridge.

Median Marker Providing and fixing of Flexible median markers as per IRC 79:2019 witch shall be made of combination of tough high impact resistant molded thermoplastic body along with florescent yellow color retro reflective type XI sheeting with minimum exposed reflective area 285 square mm and with rebound property . the reflective sheeting should confirm to type Xi Florescent yellow sheeting as per IRC 67 2012 and ASTM D4956 11. the flexible median marker shall have overall height of minimum 180mm body thickness of minimum 2mm and shank depth of minimum 30mm . the retro reflective sheeting shall be on both side of the flexible median marker and shall be edge protected with no exposed edges which will prevent edge lifting , vandalism, sheeting damage, etc. The edge of sheeting should not come out easily by putting nails, sharp objects etc. The logo of the manufacturer shall be embossed on either side of the body. The produt design has to with stand all natural impacts and should not get damaged if any pedestrian stamp on top of it intentionally or unintentionally. The product should bend up to 90 degree on both sides without breakage or damage. The product shall be tested for rebound ability and tensile test as per IRC 79-2019 and government lab test report shall be submitted along with tender. If somehow tender pre qualification condition do not ask for government report then the report shall be submitted to engineer-in-charge before finalization of bill. The rate shall include all materials, labour, equipment’s, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in-Charge.

Filling Pot-holes and Patch Repairs with open-Graded Premix surfacing, 20mm. Removal of all failed material, trimming of completed excavation to provide firm vertical faces, cleaning of surface, painting of tack coat on the sides and base of excavation as per clause 503, back filling the pot holes with hot bituminous material as per clause 510, compacting, trimming and finishing the surface to form a smooth continuous surface, all as per clause 3004.2