Mathura Vrindavan Development Authority Tender

Dismantling tile work In floors and roofs laid In cement mortar including stacking material within 50 metres lead For thickness of tiles above 25 mm and up to 40 mm

Providing and laying cement concrete In 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and curing complete, Including cost of form work. in Foundation and floors.

laying of Vitrified tiles in floor without lean concrete of 600X600mm Sizes (thickness 10mm), with waler absorption less lhan 0.08% and Conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid with cemenl based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, including grouting of joints. (Labour Rate only)

Providing and laying Vitrified tiles in floor without lean concrete of 600X600mm Sizes (thickness 10mm), with waler absorption less lhan 0.08% and Conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid with cemenl based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, including grouting of joints.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) ol approved make in alt colours, shades except burgundy, bokle green, black of any size as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cemenl: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm ncluding pointing in white cement mixed with pigment of matching shade complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coals) over and including water thinnable priming coat with cement primer including cost of all materials, labour T&P etc. required for proper completion of worh.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5 mm thick heat moulded PVC ’C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm*2 mm) thick x 15 rrxn wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. top, bottom and lock rails shall be provided both sides of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted zn the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) hick x 15 mm wide PVG sneet beading on inner side, nrid oined side of the 'C' Channel using PVC solvent adhesive etc.complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding window made of (small series) frame 52 x 44mm &sash 32 x 60 mm both having wall thickness of 1.9 :t 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Providing and fixing factory made P.V.C. door frame of slze 50x47 MI\1 with wall (thicl‹ness of 5 mm, made out of extruded Snini rlgld PVC foam sheet, milred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door freme profiles to be reinforced with 19X10 mm M.S. sq\Iare tube of 19 gauge, EPDM rHbber gasket weather seal to be provided through a\x the frame. The door frame to be fixed lo llie wall using M.S. screws of 65/t 00 mm size, complete as per manufacturer's specification and direction of Engineer- in Charge.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in- built roller track and sash extruded profiles duly reinforced with 1.60 z 0.2 mm thick galvanized mild sleel section made from roll forming process of required length (shape & size according to uPVC profile). appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc, After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. /SingIe / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding window made of (small series) frame 52 x 44mm &sash 32 x 60 mm both having wall thickness of 1.9 :t 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to glve an even shade Two or more coats on new vork including cosl of all materials, labour T&P etc. required for oper completion of worf‹. Wood and sleel

Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.25 Ltr/10sqm including one coat of primer applid @ 0.75Ltr/l0sqm coat curing and cost of all material; labour, T&P etc. required for proper completion of work.for two coat.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Class-150 (non Modular) brick work but in in 1:4 cement and coarse sand mortar super structure above plinth level upto floor five level (upto five stories) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cm.

12mm cement plaster with cement mortar in proportion of 1:4 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers and rounded angles not exceeding 80mm. In girth and finished even and smooth

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fXtings. including fixing Ihe pipe wilh clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joinls complete as per direction of Engineer in Charge.

Providing and fixing CP Brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 15mm nominal bore

Providing and fixing CP Brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete wilh 6 mm thick hard board ground fixed la w'ooden cleats brass screws and washers complete.

Wiring point for light in 1.5 sq mm FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid PVC conduit pipe concealed in the wall complete with 14 SWG copper earth continuity wire, GP Box, piano type switch & ceiling rose /angle/batten holder on 3 mm thick phenolic laminated backelite sheet etc., complete in all respect, as directed including matching colour wash.

Wiring point for fan with 1.5 sqmm. P.V.C. insulatled single core copper conductor cable in heavy gauge rigid P.V.C. conduit pipe partially laid in slab and partlly conceled in wall complete with 8 SWG GI earth continuity wire, piano type switch and ceiling rose on 3 mm thick phenolic laminated backlite sheet etc complete in all respect, including matching colour wash.

Wiring point for plug with 1.5 sqmm. FRLSH P.V.C. insulatled multistrand core copper conductor cable as earthwire drawn in the conduit complete with 14 SWG copper earth continuity wire, GP box piano type switch and socket etc. complete in all respect including matching colour wash.

S/F of 16 Amp. 240 volt D.P. metal clad rewireable type switch fuse unit of M.D.F.E.G./Teak wood board complete in all respects.