Lucknow Development Authority Tender

S\E of double pole structure with 2 nos. steel tubular pole 410 SP 55,11 mt long in 1:3:6 CC foundation including 2 nos. channel cross arms of 125mm x 75 mm (7.9 Kg/Mtr.) one no channel cross arms of 75mm x 40mm (6.8 Kg/Mtr.) 2 No. 50 x 50 x 6mm angle iron bracings with necessary nut bolts & packing pieces complete with painting as per direction of E/I. (PSR)

S\E of 11 KV TPMO switches on poles including handle rod etc. complete in all respects as approved by E\I. (Previous Sanction Rate) (PS Rate)

S\E of 11 KV D.O. fuse set on poles complete in all respects as per approval of E\I. (Previous Sanction Rate) (PS Rate)

Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. (PWD SOR-725(A)/2018)

S\M suitable earthing of the natural / body of the transformer /D/F/ lightening arrester etc. with 600mm. x 600mm. x 6mm. G.I. plate buried vertically 6 mtr. below ground level of water level and surrounded by 150mm. thick alternate layers of carcoal and salt including 2 nos. leads of 7/8 SWH. G.S. stay wire in G.I.pipe of 40mm. dia as per direction and approval of E\I.(P.W.D. S.I.2018 Item No. 703)

Supply and Laying of 80 mm dia G.I. pipe for the purpose of cable on the run pole through this G.I. pipe from level as cable carrier pipe should be tied with 2Nos. 50x6mm flat iron clamp with pole as per direction of E/I (PSR)

Supply and fixing of 250 KVA, 11/0.433 KV, 3- Phase, 50 Cycles, ONAN cooled, Delta/Star (Dyn 11 Group), Copper Wound Transformer with first fill of Transformer Oil and standard fittings confirming to IS-1180/2014 having Energy Efficiency Level-II.( as per PCL approved) with all assessores etc. complete as per direction of E/Ic Make- MEI/ KOTSON (PSR)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer- Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.

25 Sqmm 3.5 Core (PWD SOR-501(J)/2018)

70 Sqmm 3.5 Core (PWD SOR-501(m)/2018)

150 Sqmm 3.5 Core (PWD SOR-501(P)/2018)

240 Sqmm 3.5 Core (PWD SOR-501(r)/2018)

Supply and fixing of plain or pin type copper tin plated cable socket (lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the E/Ic

25 sq. mm (PWD SOR-504(E)/2018)

70 sq. mm (PWD SOR-504(h)/2018)

150 Sqmm (PWD SOR-501(K)/2018)

240 Sqmm (PWD SOR-501(T)/2018)

Supply and fixing of 40 amp TPN automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of timer switch TSO 100 series with contractors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect. (PWD SOR-807(F)/2018)

Construction of Solid B/W Transformer Plinth of size 1.5mx1.5mx1.25m above G.L.The top of the plinth shall be of RCC 15 cm thick with material & labour all complete as per direction of E/Ic. (PSR )

Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. SIN 803 (b)/2018

Incoming 315 Amp. TPN-1 No Outgoing 100 Amp. TPN-2 Nos.& 63 Amp. TPN-2 Nos. Cat. B. Cubicle Type.

Supply and laying of 3 core standered aluminium conductor XLPE (Cross linked polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade at a depth of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks on sides and on top put across. The armouring of cable shall be properly connected with earth conductor by clamps etc.

70 sq. mm 3 core (PWD, SOR-506(D))

supplying and making 70 sqmm outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required all complite as per direction of E/Ic.(PSR in basant kunj PMAY)

"Supply and fixing of 2 metres high cage fabricated with 3 mm thick expanded metal fixed on 50 mm x 50 mm x 6 mm angle iron frame having vertical members spaced at 1 to 1.25 mts. and horizontal members spaced at 1mt. The vertical members shall be grouted in floor and horizontal members in the wall to a depth of 300 mm with ends forked. The cage shall have 2000mm x 1000mm size one leaf door with locking device having door frame fabricated with 35mm x 35mm x 6mm angle iron and 3mm expanded metal duly fixed with the cage member with hinge etc. the cage shall be painted with red oxide primer and synthetic enamel paint. The job includes all materials, labour T & P etc. for proper completion of work. PWD, SOR-1142, 2018"

Part - B

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 and above Protection complete in all respect. SI. No. 1423/2018 CAT- AAA

S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve Cat-A, SIN- 1002

S/W of submain with two Nos. of 2.5 Sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material Labour and T&P required for proper completion of the work as directed at site by E/I. SI. No. 289/2018.

Supply and fixing of 40mm dia 1.5 Mtr. Long G.I. Pipe bracket complete with 02 Nos. "D" clamps of 50 mm x 6mm flat iron on steel tubular poles . Proper completion of work as per direction of E/I. (PSR)

Part - C

First Year Operation Part A @ 0.5%

Second Year Operation & Maintenance Part A @1%

Third Year Operation & Maintenance Part A @1.5 %

Fourth Year Operation & Maintenance Part A @2.5%

Fifth Year Operation & Maintenance Part A @3.5%