Jhansi Development Authority Tender

Cement concrete with 2cm gauge approved stone ballast, approved coarse sand and cement in the proportion of 4:2:1 including supply of all materials, labour and T&P etc. required for porper completion of the work.As per S.I. No. new item page no 40

Providing & injecting chemical emulsion for pre-constructional antitermite treatment and creating a chemical barrior under and around the column pits wall trenches basement excavation top surface if plinth junction of wall and floor, along the external perimeter of binding expaction joints, surriunding of pipes and cinduit etc., complete (plinth area of the building at ground floor only shall be measured as per IS-6313 Part II 1981)Aldrine emulisifiable concrete or any other approved material such as Hepthachlor or Chordance will be used. The rate of application of chemical emulsion shall be as follows- (i) Treatment for masonary & foundation 5 Ltr. Per Sqm. (ii) Back fill in immediate contact with foundation 5 ltr. Per sqm. (iii) Treatment of top surface of plinth filling 5 ltr. Per sqm. (iv) Treatment of soil along external peri meter of building 7.50 Ltr. Per Sqm. (v) Treatment of soil under apron along external peri meter 5 Ltr. Per Sqm. As per S.O.R. Chapter - 18 SI No. 1

R.C.C. work with cement approved coarse sand and 20mm gauge stone aggrigate with M-20 nominal mix 1:1.5:3 in Plinth Beam & excluding the supply of reinforcement and its bending but including its fixing and binding with 24 BWGGI binding wire, centering and shuttering, supply of all materials, labour and tools and plants etc. required for proper completion of work .As per S.I. No. 285(1)

R.C.C. work with cement approved coarse sand and 2cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in heavier beams excluding supply of reinforced and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour & T&P etc. required for proper completion of the work. Binding wire cost being including in the item.As per S.I. No. 286(1)

Mild Steel or Iron work in plain work such as reinforced cement concrete (when not included in over all rate) wrought to required shape as necessary including bending for proper completion of work, supply of steel, all labour etc. required and including wastage bend, hooks and authorised over lapping shall be measured. As per S.I. No. 504

M-150 brick work in 1:4 cement and C/sand mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of work.As per S.I. No. 305

15mm thick plaster with cement mortor inproportion of 1:4 cement and C/Sand over brick work minium thickness not be less than 10mm including supply of all materials, labour and T&P etc. required for proper, comletion of work.As per S.I. No. 17.59(II) Outer Face side of wall (G.F.)

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.As per D.S.R. 13.80

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.As per D.S.R. No. 11.41.1

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.As per D.S.R. No. 11.55.1

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m².As per D.S.R. No. 12.1.1

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Electric resistance or induction butt welded tubes.As per D.S.R. No. 10.16.3

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF/ Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.As per D.S.R. No. 8.32

Providing and fixing aluminum U beading of required size to Pre-laminated/wall frame(internal/external), including fixing etc. complete as per direction of Engineer-in-charge.As per D.S.R. No. 9.132

Supply of M.S. Angle iron door,windows ventilation frame made of approved M.S. angle iron wrought to required form including drilling hole, welding and recetting where necessary and also including supply of all materials, such as steel hinges of required size, nut & bolts etc. and also including all taxes, wastage and one coat of red oxide paint complete in all respect as per direction of engineer-in-charge for proper completion of work at site of work.As per S.I. No. 2 (Chapter-10) (50X50X3mm=4.39/Meter)

Supply & Fixing Latter of Glow & Shine Sheet.As per Approved Rate.

Ring machine and submersible pump set material PBC from Jal Nigam Bhandar. Carrying pipes, strainers and all material cement etc. to the site. Value of supply of materials required for submersible installation work

165 / 115 MM Size D.T.H. Punching and PBC with Ring Machine Lowering of assembling Cost of PVC Casing

Cost of punching

After the installation of the submersible pump set, the development work of the submersible pump till the recommendation of the engineer in-charge

After development work including disinfection work material

Construction of platform of 1.85 m diameter (including all material and cement) as per approved drawing

Water Testing & Photography

K.S.B. 100 L.P.M. 45 Meter Head 1 H.P. Submersible Pump Set

L & T Make Control Panel

1.5 mm2 Finolex make submersible cable

32mm PVC Pipe

32mm Adapter set

Bell Cap

Clamp

Wire Rop

Valb Set

Installation charge

P/L 20mm Thick kota Stone flooring over 20 mm thick base of cement mortar 1:4 (1 cement :4 course sand) Laid over joited with grey cement slurry mixed with pigment to match the shade of slabs including rubbing and polishing complete.SI No.14.43(a)

ELECTRICAL Wiring point for light with 1.5 sq.mm FRLSH PVC insulated multistrand single core Copper Conductor cable in PVC conduit pipe partly concealed in wall & partly laid in slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable earth continuity wire, piano type switches & ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash. As per S.I. No. 138(C)

Addition for light with modular type switch in place of piono type switch.As per S.I. No. 187(A)

Supply & wiring of submains with two number 2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit with 1 Number 1.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect.As per S.I. No. 1307(C)

Supply & wiring of submains with two number 4 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit with 1 Number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect.As per S.I. No. 221(C)

Supply and wiring of submain 2 number 6 sqmm . FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in 20mm dia heavy duty (2mm thick ) PVC conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 4.0 Sqmm FRLSH PVC Multistand copper earth contunity wire including colour wash etc. complete in all respects.As per S.I. No. 222 (C)

Supply and wiring of submain with 4 number 10 sqmm . FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in 32 mm dia heavy duty (2mm thick ) PVC conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with two number 10 SWG copper earth contunity wire including colour wash etc. complete in all respects.As per S.I. No. 278 (C)

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 15 Watt. to 25 Watt. Confirming to IP 66 protection complete in all respect. As per S.I. No. 1419 Cat. AAA

Supply & fixing of cove light NARANG LED Neon Light Rope, Waterproof Outdoor Flexible Light Strip Flexible Frosted Light for Diwali Christmas Home Decoration (5 Meter) (Blue) complete in all respect.As per Approved Rate.

Supply & fixing of Façade light Outdoor Flexible complete in all respect.As per Approved Rate

Supply and burying of 40mm dia x 4.5 metres long G.I. pipe, vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No.6 to 8SWG G.I.wire in G.I. pipe upto appron (and from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) upto switch board, 30cm. square C.I.box with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.As per S.I. No. 701

Supplying and fixing of one number 8 SWG G.I. wire in 15mm dia G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T & P other material required for proper completion of the work as directed at site.As per S.I. No. 721

Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose as required complete in all respects.As per S.I. No. 716

Supply & fixing of two number 8 SWG G.I. wire for earthing purpose as required complete in all respects.As per S.I.No. 723

Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve. As per S.I. No. 1002 5 - 32 amps.Cat. A

Supply and fixing 25 Amp. TPN miniature circuit breakers in existing MCB, DB complete in all respects as required.As per S.I. No. 1019

Construction of recess distribution board of all sizes including cutting of brick work providing lintel of suitable size & thickness plastering etc. with supply of all materials, labours, T & P etc. required for proper completion of work.As per S.I. No. 1141B 600x480x200 mm. size

Supply and fixing of factory fabricated M.S. box in existing sunk with Godrej type almirah cover with handle etc. fabricated from 18 SWG M.S. sheet duly painted with red oxide primer followed by two coats of synthetic enamel paint complete with necessary conduit entry and DP/TPN; fixing arrangement and provision for compartment for loose wires, openable housing on the top and hold fast etc. including supply of all material, labour and T & P etc. required for proper completion of the work.As per S.I. No. 1147 600x480x200 mm. size

Supply and fixing of surface/ flush mounting 6 way TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer Incharge.As per S.I. No. 1027 (A) CAT A

Supply & fixing of Sheet Steel Enclosure Surface/ Flush Mounting fitted With 20/32 Amp. 2Pin and earth metal clad scraping earth plug and socket complete in all respects as per direction and satisfaction of engineer-in-charge.As per S.I. No. 1031

PART B - ROAD WORK Clearing jungle including uprooting of rank vegetations grass,bush,,wood trees and saplings of girth upto 30cm. Measured at a height of 1meter above ground level & removal of rubbish upto a distance of 50 meters outside the peripheri of area cleaned./SI No.259

Earth work in cutting or in filling in ordinary soil, excavation tto be in the form of regular pits not exceeding 1/2 meter (20") in depth and earthwork in embankment to be in 20 cm (8") layers, including ramming & dressing the surface to required levels and slops and also including 1.50 meter(5fts) lifts and 30 m. (100 fts) lead. the earth from cutting to be used in making filling or to be deposited as spoil banks withinn 30 metrs (100 fts) distance as directed by ingineer-in-charge.(Rate including royalty)/SI No.2

Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material within all lifts and lead upto 1km (by mechanical means)./Analysed Rate

Construction of granular sub-base by providing course graded material spreading in uniform layers with moter grader on prepared surface mixing by mix in place method with rotovator at omc and compacting with vibratory roller to achieve the desired density complete as per clause 401.Analysed Rate

providing and applying Tack Caot with bitumen VG-10 using Bitumen pressure distributor at the rate of 0.35 kg per sqm on the prepared granular surface cleaned with mechincal broom.

Providing and laying Bitumenous concrete with 100.120 TPH batch type HMP producing an average output of 75 tones per hour using crushed aggregate of spacified grading premixed with bitumenous binder 5.40 percent by weight of total mix and filler transporting the hot mix to work site laying with hydrostatics paver finisher with senser control to the required grade level and aligment rolling with smooth wheeled vibratory and tendem rollers to achiev the desired compaction as per MORTH spacification clause no.508 SI no.509 complete in all respects./Analysed Rate

Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications./JDA Approved Rate

Supply and fixing of pavement maker (Cat Eye) Type X-ASTMD-4956-04 Avery Dennison /3-M (USA Maker) consisting of ASA plastic housing fitted with lightly adherent plotting componud. The housing shall contain prismatic two glass covered prismatic reflective face to reflect incident light i/c all tax. /JDA approved Rate

Providing and laying of 80mm interlocking concrete block pavement laid in in stone dust base and fill joint with fine sandjoint filled after leveling and dressing baseincluding supply of all materials labour T&P etc required for proper completion of the work . SI No.New item no 14.43 new item 3 SI No14.43 new item 3