Jhansi Development Authority Tender

Earth work in filling plinth with cartage earth with a lead of 10.00 Km from the site of work including, loading, unloading, filling, leveling, watering compacting and dressing as per required at site.As per S.I. No. 253+231 (A)

Concrete with 40mm gauge stone ballast, C/sand in 8:4:1 in foundation including supply of all materials labour and tools and plants etc. required for proper completion of work.As per S.I. No. 281

Providing & injecting chemical emulsion for pre-constructional antitermite treatment and creating a chemical barrior under and around the column pits wall trenches basement excavation top surface if plinth junction of wall and floor, along the external perimeter of binding expaction joints, surriunding of pipes and cinduit etc., complete (plinth area of the building at ground floor only shall be measured as per IS-6313 Part II 1981)Aldrine emulisifiable concrete or any other approved material such as Hepthachlor or Chordance will be used. The rate of application of chemical emulsion shall be as follows- (i) Treatment for masonary & foundation 5 Ltr. Per Sqm. (ii) Back fill in immediate contact with foundation 5 ltr. Per sqm. (iii) Treatment of top surface of plinth filling 5 ltr. Per sqm. (iv) Treatment of soil along external peri meter of building 7.50 Ltr. Per Sqm. (v) Treatment of soil under apron along external peri meter 5 Ltr. Per Sqm. As per S.O.R. Chapter - 18 SI No. 1

R.C.C. Work with cement approved coarse sand and 2cm gauge stone girt (Dala) in the propotion of 1:1.5:3 (M-20) in column footing excluding supply of reinforcement and its bending but including fixing and bending the same with 24 B.W.G.G.I. banding wire and including necessary centering and shuttering etc. & also including for proper complrtion of work.As per S.I. No. 287(1)

R.C.C. work with cement approved coarse sand and 20mm gauge (nominal size) dalla stone aggregate in the proporation of 1:1.5:3 M-20 in R.C.C. column excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and as required supply of all materials, labour centering and shuttering and removal of the same after completion of work.AS per S.I. No. 288(1)

R.C.C. work with cement approved coarse sand and 20mm gauge stone aggrigate with M-20 nominal mix 1:2:4 in Plinth Beam & excluding the supply of reinforcement and its bending but including its fixing and binding with 24 BWGGI binding wire, centering and shuttering, supply of all materials, labour and tools and plants etc. required for proper completion of work .As per S.I. No. 285

Mild Steel or Iron work in plain work such as reinforced cement concrete (when not included in over all rate) wrought to required shape as necessary including bending for proper completion of work, supply of steel, all labour etc. required and including wastage bend, hooks and authorised over lapping shall be measured. As per S.I. No. 504

M-150 brick work in 1:4 cement and C/sand mortar in foundation and plinth including supply of all materials, labour and tools and plants etc. required for proper completion of work.As per S.I. No. 305

12mm thick plaster with cement mortor inproportion of 1:4 cement and C/Sand over brick work minium thickness not be less than 10mm including supply of all materials, labour and T&P etc. required for proper, comletion of work.As per S.I. No. 17.58(II) Exterior rough face of wall

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.As per D.S.R. 13.80

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).As per D.S.R. No. 13.47.1 Exterior rough face of wall

Supply & laying of Black cotton soil including all labour, material & T&P etc all complete.(Approved Rate)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).As per D.S.R. No.10.28

Gate Work Dismantling reinforcement cement concrete or reinforcement brick work, including stacking of materials as directed by Engineer-in-Charge.As per S.I. No. 694

R.C.C. work with cement approved coarse sand and 20mm gauge (nominal size) dalla stone aggregate in the proportion of 1:1.5:3 M-20 in R.C.C. column excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and as required supply of all materials, labour centering and shuttering and removal of the same after completion of work.AS per S.I. No. 288(1)

R.C.C. work with cement approved coarse sand and 2cm (3/4") gauge approved stone ballast in the proportion of 1:1.5:3 in heavier beams excluding supply of reinforced and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour & T&P etc. required for proper completion of the work. Binding wire cost being including in the item.As per S.I. No. 286(1)

Mild Steel or Iron work in plain work such as reinforced cement concrete (when not included in over all rate) wrought to required shape as necessary including bending for proper completion of work, supply of steel, all labour etc. required and including wastage bend, hooks and authorised over lapping shall be measured. As per S.I. No. 504

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.As per D.S.R. 13.80

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).As per D.S.R. No. 13.47.1 Exterior rough face of wall

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.As per D.S.R. No. 8.32

Providing and fixing aluminum U beading of required size to Pre-laminated/wall frame(internal/external), including fixing etc. complete as per direction of Engineer-in-charge.As per D.S.R. No. 9.132