Jhansi Development Authority Tender

LT CABLE Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (a) 16 Sqmm 2 CorePS No. MR

(b) 35 Sqmm 3.5 CorePS No. MR

(c) 150 Sqmm 3.5 CorePS No. MR

(d) 185 Sqmm 3.5 CorePS No. MR

(e) 240 Sqmm 3.5 CorePS No. MR

VCB & TRANSFORMER HT VCB 11 KV 1200 Ampere 1 Incoming 5 Outgoing Complete as Per Direction of Engineer in Charge PS No. MR

SITC of 33 /11 KV , 3 MVA DYN 11 Copper Wound Delta Star , Outdoor Type Transformer with onload Transformer with on load tap changer having losses IE . No Load Loss 7 KW and full Load Loss 50 KW with oil level indicator , breather , thermometer conservator with Bochhalz relay vent pipe to IS Confirming to IS 2026 Part 1 & 4 including Loading unloading and Cartage complete in all respects as per direction of Engineer in Charge .PS No. MR

Transformer 11/0.433 Copper Wound Capacity 400 KVA as Per Direction of Engineer in Charge PS No. MR

Construction of Plinth upto Height 4 Ft for Transformer 11/0.433 Copper Wound Capacity 250 KVA Complete as Per Direction of Engineer in Charge PS No. MR

Work of Fencing of Transformer & VCB Complete as per Direction of Engineer in Charge PS No. MR

S/F of double pole structure with 2 Nos. Bottom Galvanzed S.T. pole 410 S.P-55 in 1:3:6 C.C foundation 1/6 of pole length below G.L 20cm thick around the pole with 1Nos, channel 100mmx50mm 1 Nos channel 75mmx40mm Necessary nuts bolts complete with painting etc., as per direction of E/InchPS No. MR

Supply and fixing of 11 KV.T.P.M.O set complete in all respects,PS No. MR

Supply and fixing of 11 K.V.D.O fuse set complete in all respects.PS No. MR

Supply and erection of lightening arrestor set (3Nos) suitable for mounting on steel 30 support complete with all material labour T&P etc. required for properPS No. MR

Supply and fixing of 33 K.V pin insulator with G.I pin and nut bolt on main Terminal gantry and makin other connection.PS No. MR

Supply and fixing of 33 K.V disc insulator (B&S type suitable for 7000 Kn) including gun fitting on cross arm/clamps fixed on poles complete in all respects as per direction of E.IPS No. MR

Supply and fixing of 33 K.V. 800 Amp Bus type isolator of approved quality and make with all necessary material required labour T&P etc. required for proper fixing on structure including all material for proper completion of work.PS No. MR

Supply and fixing of 33 K.V. 800 Amp line type isolator of approved quality and make with all necessary material required for proper fixing on structure including all material LabT&P etc. for proper completion of work.PS No. MR

Supply and fixing of 33 K.V-10 K.V. lightening arrestor set (3 Nos. of approved quality and make with all necessary material labour T&P etc. for proper fixing onstructure and completion of work.PS No. MR

Supply and fixing of 33 K.V CT of 400/200/1 Amp of approved quality and make with all necessary material labour T&P etc. for proper fixing and completion of work.PS No. MR

LT PANELS Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN ACB(65 KA,4Pole Elect draw out , Micor processer Release IPR2 ) and TPN MCCB's (Four Pole 36 KA with thermal magnatic release) Switches and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, istrument fuses, current transormer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/ DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches entry boxes shall be complete with suitable cable end boxes reverse.The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above Will be provided with Amp Metre, current transfonners and selector switches etc and insurtrment fuse. The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6 mm/2mm. (a) Incoming - 630 Ampere ACB - 1 No (b) Outgoing - 250 Ampere MCCB = 03 Nos. & 100 Ampere MCCB = 03 Nos

Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB's (Four Pole 36 KA with thermal magnatic release)Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters(KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB's shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. PS No. MR (a) Incoming - 250 Ampere MCCB = 01 Nos. (b) Outgoing - 100 Ampere MCCB = 04 Nos

Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control Bus Bar panel Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters(KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The Bus Bar Panel shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc.The Job includes the grounting of the board as per directions of Engineer-in charge. . The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. PS No. MR (a) 150 Ampere Aluminium Busbar Suitable for 12 Nos Outgoings

Supply and burring of Safe Earthing Electrode T-39 (Hot-Dip Galvanized), Length up to 3000mm, outer pipe 76mm inner Dia 38mm terminal Dia 12 mm ,outer GI pipe of 16 SWG and inner GI pipe of 12 SWG with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 X 3 GI. Strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. CertifiedPS No. PWD SOR - 725 (D )

Supply and laying of 32mm x 6mm copper strip from earth electrode directly in the ground as required complete in all respectPS No. PWD SOR 718

Supply & Fixing following capacity of Automatic street light cubicle control panel painted with anti corrosive Alakil and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses , isolating switch metering instrument & Instrument box with CT's etc in case of 40 Amp TPN , complete in all respect ( SOR No. -807(F))PS No. PWD SOR -807 - f

Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.PS No. PWD SOR -645

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 Watt. Confirming to IP 66 and above Protection complete in all respect. CAT- AAAPS No. PWD SOR -1423

Supply & fixing of 12.5 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect.PS No. PWD SOR -651

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 Watt. Confirming to IP 66 protection complete in all respect. CAT- AAAPS No. PWD SOR -1455

Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. CertifiedPS No. PWD SOR -725 ( A )

Supply and fixing of decorative 40 to 45 Watt LED Post top indirect light luminaire having Pressure die cast aluminium body and Clear glass with driver set confirming to IP 65 and above protection complete in all respect. CAT-AAAPS No. PWD SOR 1443

Supplying & Fixing GI Pipe 50 mm dia B Class 4 M Long with grouting including all material labour and t&P etc as per direction of Engineer incharge at sitePS No. MR

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. (a) 63 mm Dia (OD-63mm & ID-51 mm Nominal )PS No. DSR - 14.16.1

(b) 200 mm Dia (OD - 200 mm & ID - 175 mm Nominal )PS No. DSR - 14.16.5

Supply and wiring of submains with 2 nos. 2.5 sq mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing PVC conduit complete, including supply of all material, labour and T & P etc. required for proper completion of the work as directed by Engineer in charge. PS No. MR