Irrigation Department Tender

Dismantling existing old plaster on brick masonry including disposal of refuse with in distance of 60M as per direction of E/I charge.

Dismantling old brick work in cement mortar and including stacking of material within a distance of 60M as per direction of E/I charge.

Class M-150 Brick work in (1:6) CM using (2.0 Bag of cement per Cu.M of Brick work) i/c cost of all Material, Labour, T&P etc With Complete work as per direction of E/I charge.

Centring and Shuttring i/c cost of all Material, Labour, T&P etc With Complete work as per direction of E/I charge.

R.C.C. work with cement approved coarse sand and 2cm (3/4") gauge approved stone ballast in the proportion of 1 :1.5: 3 in Foundation and footing of Coulmn, T-beam, slab and also including supply of all materials, labour T&P etc. required for proper completion of work as per direction of E/I charge.

Reinforcement for R.C.C. and R.B. work including cost of reinforcement and its binding but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including necessary centering and shuttering etc. and also including cost of all materials, labour T&P etc. required for proper completion of work as per direction of E/I charge.

12.5mm Cement plaster in 1:4 cement mortar ratio in brick wall with cement & coarse sand including cost of material, labour T&P etc.with proper complection of work as per direction of E/I charge.

Providing and fixing (Door panneling) with Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS: 3087 marked, with one side decorative and other side balancing lamination Grade 1, Type II exterior grade IS: 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick Door panneling as per direction of E/I charge. (For Door Pannaling)

Providing and fixing (Doors) with Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS: 3087 marked, with one side decorative and other side balancing lamination Grade 1, Type II exterior grade IS: 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 35 mm thick as per direction of E/I charge. (For Fixing Door)

Providing and fixing (Doors Assessories) including Cost of all materials ISI Mark, labour T&P etc. required for proper completion of work as per direction of E/I charge.

P/F Door Closer in Meeting Hall, Attached W/C Kitchen, Main Door W/C

P/F Door Closer in Common Bathroom Doors

P/F Doors lock

P/F Tower Bolt in doors

P/F Stopper in doors

P/F Buffer in doors

P/F Hinge in doors

Providing and fixing factory made UPVC glazed/wire mesh windows/ doors comprising of lead free UPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, UPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all comers, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.[Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly+A8 screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre)Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m).] Material used fenesta make or its equivalent.

Providing and laying PCC with approved stone ballast, approved coarse sand and cement in the proportion of 1 : 2 : 4 including supply of all materials, labour and T&P etc. required for proper completion of the work as per direction of E/I charge.

Providing and laying PCC with approved stone ballast, approved coarse sand and cement in the proportion of 1 : 3 : 6 including supply of all materials, labour and T&P etc. required for proper completion of the work as per direction of E/I charge.

Providing and laying Vitrified tiles in sizes 1200x600mm (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to I.S. 15622, of approved make in all colours & shade, in skirting, riser of steps, over Avg 20mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), joining with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete as per direction of E/I charge.

Scraping old white or colour wash including disposal of refuse material as per direction of E/I charge.

Providing and applying white cement based putty of Avg. thickness 1mm of approved Brand and manufacturor over the plastered wall surface to prepare the surface even and smooth including cost of material, Labour and T & P etc. complete as per direction of E/I charge.

Finishing wall with water proofing cement paint of approved manufacturers on uncoated wall surface(two coat) over one coat white cement primer including cost of curing , Labour, Material, T&P etc. for proper completion of work as per direction of E/I charge.

Wall Panelling in (meeting hall) with providing and fixing in position wall panels of one side laminated phenol formaldehyde synthetic resin tiles over kail wood frame and provision for providing switch board fixtures etc.as per drawing complete with polishing and fining with French/wax polish aas per direction of E/I charge.

Providing and fixing (False Ceilling) with Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer- in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60 (including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels. 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm cóc, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with )[Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer- in-charge and as per manufacturer's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60]

Wring point for H.P.M.V./H.P.S.V. LAMP with 2.5 sq. mm P.V.C./V.I.R. insulated single core cable in heavy gauge rigid steel conduit pipe on surface complete with 8 SWG G.I. Earth continuity wire with 15 Amp.metal clad /S.P.N. switch etc. complete in all respect (a) 16 Amp Points

Providing & Fixing Wring point for light and fan with 1.5 mm² P.V.C./V.LR. insulated single core cable in heavy gauge rigid steel conduit pipe on surface complete with 8SWG G.I. Earth continuity wire and piano type switch etc. complete in all respect (b) 5 Amp Points

For Plug

For Fan

For Exaust Fan (Ceiling or wallFan)

For Fresh Air Fan

For Light

For call well

For Internet Eathernet Cable

C.C. TV Camera Cable (Cad 3 Cabel)

Intercom Cable

Providing and fixing of 32A 240V D.P. metal clad Rewireable type switch fuse unit on teak wood board complete in all respect.

Providing and fixing of 36 Watt to 46 watt surface mounting LED Square fitting having powder coated die cast alluminium housing body with extended heat sink and diffuser of polycarbonate material and driver set Complete in all respect (ISI Mark)

Providing and fixing of 12 Watt to 15 watt indoor rescess mounting LED Square fitting for Armstrong celling having powder coated ie cast alluminium housing body with extended heat sink and diffuser of polycarbonate material and driver set Complete in all respect (ISI Mark)

Providing and fixing of Profile light i/c Cost Of Material labour T&P etc with complete work (ISI Mark) as per direction of E/I charge.

Sanitary Fittings (ISI Mark) i/c Cost Of Material labour T&P etc with complete work as per direction of E/I charge.

(a) P/F 12mm dia. CPVC pipe of 6m length

(b) P/F 25mm dia. CPVC pipe of 6m length

(c) P/F 20mm dia. CPVC pipe of 6m length

(d) P/F 100 mm dia. CPVC pipe of 6m length

(e) P/F Water Storage Tank capacity of 500 Ltr.

(f) Providing and Fixing Wash Basin with fittings

(g) Providing and Fixing Sink in Kitchen with fittings

(h) P/F C.P. Pillar Cock

(i) P/F C.P. Bib Cock

(j) P/F C.P. Stop Cock

(k) P/F Urinals

(l) P/F Mixer Tap in Kitchen, Bathroom

(m) P/F Shower rose with Tap

(n) P/F T- Socket

(o) P/F Elbow

(p) P/F Socket

(q) P/F Union

(r) P/F W.C Pan (Western Type) with Accessories in ACEO W/C & Meeting Hall W/C

(s) P/F W.C Pan (Western Type) with Accessories in Comman Wathroom W/C

(u) P/F W.C. Trap

(v) P/F Floor Trap

(w) P/F Gully Trap

(x) P/F Hand Touble Rail

(y) P/F Soap Stand(Stain Less Steel)

(z) P/F water tank ball cock valve