Indian Army Tender

Bed Stead Iron Hospital TP , Bed Stead Iron Hospital Dimesions 1980 mm length x 910 mm width x 600mm height Over all description Two section Mechanically operated fixed height with back rest adjustment Mechanism of action Handle wound mechanicall operatd fixed height Raw meterial Tubular Mild and Machine pressed steel of CRCA quality Main frame Strong and sturdy frame of mild steel with perforated 2 section top of 18 swg 1 point 25mm Thickness and corner buffers Head and Foot bows both side MDF board of 20mm thickness Panels framed in 31mm dia detachable 350mm high stainless steel Head and Foot bows Back Nee Rest Handle at foot end to wound lever operated backrest Handle to fold inwards when not is use Range 0 to 80 deg Base Non trolly type base on legs with rubber feet or trolley type on castors as required Tubular steel with 32mm dia Castors 100mm dia castors with brakes on opposite Corners Finish Pre treated 7 stages with epoxy powder coated oven baked Colour Ivory white white warm grayAttachments One Epoxy coated IV Rod wtih 4 IV Rod location points and Mosquito net road

Board Notice 8 FEET x 4 FEET FD 99 M , Board Notice 8 FEET x 4 FEET All as shown on drawing Overall size shall be 2400x1200x750mm top and bottom shall be of first class teakwood frame 75x75mm of in section made to shape as shown on drawing green baize cloth of best quality shall be fixed on 12mm thick soft board fixed on 6mm thick commercial plywood irrespective of what is shown on drawing Front shall have two shutters openable hinged on sides front frame of shutter sahll have styles and rails of 45mm wide and 25mm thick teakwood Two horizantal stiffners 19mm x 25mm in section shall be provided at equal spacing as shown on drawing One vetical stiffner 19mm x 25mm shall be provided in the centre Glass for glazing iron front shutters shall be 5mm thick fixed with 10mm x 10mm teak wood beads 75mm long hinges two in numbers to each shutter shall be provided 40mm x 25mm x 3mm thick key plates shall be provided all as shown drawing all wood surfaces exposed to view when placed in position shall be French polished with high gloss finish Steel and iron surfaces shall be given two coast of paint overa coat of primer All as directed by Engr in Charge

Book Case Steel FD 1028 , Book Case Steel DIMENSION Over all size shall be of 840 mm long 310 mm wide and 1675 mm high DESCRIPTION All sheet shall be mild steel sheet 1 mm thick back sides bottom top and shelves The book case shall be provided with four compartments of equal size The shutters of each compartment shall open towards top and slide into the depth of the book case Transparent glass 4mm thick shall be provided to front shutters Two steel handles of 100 mm long shall be provided to each shutter of the compartment The locking device shall be provided to each compartment with duplicate key and each shutter shall be provided with decorative key plate FINISH All steel surfaces internally and externally shall be painted with two coats of silver powder coated paint over a coat of primer with spray machine after preparation of surfaces All as directed by Engr in Charge

Chair Revolving Executive TP , Chair Revolving Executive Chair Revolving Executive high back with foot rest Nylon base gass lift and seat Tapety

Chair Revolving Steel Regency TP , Chair Revolving Steel Regency DIMENSION The Base pedestal assembly of chair computer shall be of dia 700mm and 1060mm high DESCRIPTION The pedestal assembly shall be provided with injection molded in black 30 percent glass filled nylon A 10 point 5mm dia forged bright Zinc plated MS Castor Pin is of press fitted into each prong for holding the castors The seat and back of the chair revolving HB shall be made of 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam The back form shall be designed with contour lumber support for extra comfort with PVC lipping allround The back rest shall be adjustable and consist of drop lift mechanism and shall be adjusted in the insert It shall be scratch and weather resistant Rest all as per drg and as per sample approved by BSO GE All as directed by Engr in Charge FINISH Pre treated with epoxy powder coated oven baked with ivory white color white warm grey

Chair Revolving Mid Back TP , Chair Revolving Medium back PP Arms Nylon base gas lift Net back and seat fabric Tapesty

Chair Visitor TP , Chair Visitor DIMENSION The overall size of the chair shall approx be 950mm high 500mmwide DESCRIPTION It shall be of trade pattern and of one make and model as described The size dimensions of the chair shall meet the overall specification as described The frame of the chair shall be of MS tubular frame powder coated cantilever type of size 25mmx10mm in section Back form shall be designed with contoured lumber support for extra comfort 120mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping alround shall be provided at seat and back Arm rest shall be of black integral skin poly urethane with shore A hardness and reinforced with MS insert It shall be scratch and wheather resistant Both hand rest section shall have inner and outer dia of 210mm and 230mm respectively and have slope towards front All as directed by Engr in Charge FINISH Pre treated with epoxy powder caoted oven baked with ivory white colour white warmgrey

Charpoy IP Hard Top Steel FD MAP II 01 , Charpoy IP Hard Top Steel DIMENSION Overall size shall be 1980mm long 900mm wide and 440mm high DESCRIPTION Two long rails and two short rails shall be of 25mmx65mmx16 guage MS rectangular pipe The legs shall be of size 32mmx32mmx16 guage welded to long and short rails as shown on drg Two stiffeners of size 25mmx25mmx16 guage shall be provided in equidistant between two opposite long rails Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply Two stiffeners joining legs of size 25mmx25mmx16 guage shall be provided at 150mm from ground level 12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt PVC hard rubber shoes shall be fixed at bottom of each legs All as directed by Engr in Charge FINISH All steel surfaces shall be Pre treated with epoxy powder caoted oven baked with black colour

Couch Examination FD 122 M , Couch Examination All as shown on drawing Overall size shallbe 1800 mm long 900mm wide 760mm high Frame and legs shall be 25mm squre steel tube of wall thickness 1 point 6mm Top shall have eleven rows of 100 mm dia copper coated springs 100mm high containing six springs in each row fixed on 12mm thick teak wood planks at equal distances Marking cloth of 120 GSM and good quality shall be provided over the spring over which 25mm thick layer of coir to be provided on sides and top of marking cloth The coir is sandwitched with another marking cloth 25mm thick and 12mm thick cotton layer is spread over the Hessaan cloth 25mm thick 32 Density foam shall be provided over cotton layer and upholstered with leatherite to give uniform smooth surface 25mm x 25mm teak wood fillets alround shall be provided over 12mm thick plank to give support to springs coir and cotton A drawer of 380mm 600mm shall be provided on left side of couch examination Above the drawwer a shelf shall be provided as shown on drawing All steel surfaces shall given two coats of enamel powder coated paint over a coat o Red oxide primer after preparation of surfaces All as directed by Engr in Charge

Display Board Wall mounted white sunmica glazed of size 5 feet x 3 feet x 160mm with aluminium channel TP , Display Board Wall mounted white sunmica glazed of size 5 feet x 3 feet x 160mm with aluminium channel All as shown on drawing Overall size shall be 1500x900x160mm top and bottom shall be of first class teakwood frame 75x75mm of in section made to shape as shown on drawing green baize cloth of best quality shall be fixed on 12mm thick soft board fixed on 6mm thick commercial plywood irrespective of what is shown on drawing Front shall have two shuttersopenable hinged on sides front frame of shutter sahll have styles and rails of 45mm wide and 25mm thick teakwood Two horizantal stiffners 19mm x 25mm in section shall be provided at equal spacing as shown on drawing One vetical stiffner 19mm x 25mm shall be provided in the centre Glass for glazing ion front shutters shall be 3mm thick fixed with10mmx10mm teak wood beads 75mm long hinges two in numbers to each shutter shall be provided 40mm x 25mmx 3mm thick key plates shall be provided all as shown drawing all wood surfaces exposed to view when placed in position shall be French polished with high gloss finish Steel and iron surfaces shall be given two coast of paint powder coated over a coat of primer All as directed by Engr in Charge

Foam with Back fd 78 m , Foam with Back DIMENSION Over all size shall be of 1800X510X900MM DESCRIPTION wooden seat shall be of teak wood in one piece and of size 1800mm long 255mm wide and 25 mm thick bolted to frame with 3 mm dia GI nut bolt and washers Steel frame shall be 1500mm long in such a way that teak wood seat shall project 150mm from frame on each side Back rest shall be of teak wood and 1800mm long 150mm wide and 19mm thick The back rest shall be 1800mm long the width is 300mm at bottom and 255 mm at top of wooden plank Legs shall be 25mm MS tube of wall thickness 1 point 6mm Steel frame shall be provided with 25mm square MS tube 16 gauge All Dimensions shape and size shall be followed as per drg All as directed by Engr in Charge FINISH All wooden expose surfaces shall be french polished two coats after preparation of surfaces and steel portion shall be painted with synthetic enamel black paint

Hat Stand with Mirror fd 1110 , Hat Stand with Mirror Overall size shall be 1000mm long 710mm high 25mmx37mm teak wood frame shall be provided alround the Hat stand 19mm thick MDF Board of size 1000mmx710mm shall be provided as back of hat stant Copper anodized aluminium peges four on the left side of mirror and three below the mirror shall be provided as shown on drawing and as directed by Engineer in charge 5mm thick mirror of Goldfish of Modiguard or Atul shall be provided The size of mirror shall be 300mmx460mm made to shape as shown on drawing shall provided with in 18mmx25mm teak wood edging all around the mirror mild steel key plate shall be provided at both top corners of the hat stand all teak wood surfaces shall be given high gloss French polish with lacquer finish All steel surfaces shall be painted with two coats of enamel paint over a coat of primer All as directed by Engr in Charge

Ladder for Loft FD 44 M , Ladder for Loft DIMENSION Overall size shall be of 2310mm long and 363 point 5mm wide DESCRIPTION The ladder shall be of Aluminium having wall thickness 3 point 18mm Each rung shall be of 23mm dia aluminium pipe with wall thickness not less than 2 point 43mm and shall be eight in nos at equidistant space of 300mm in between as shown in drgThe stringer of ladder shall be 31 point 75mm wide and 3 point 18mm thick Each alumnium pipe rung of 23 mm dia shall be fitted inside the stringer with end bend to shape and each rung on both sides shall be provided with hard rubber cap Hard rubber caps shoes shall be fixed at the ends of aluminium rungs and stringers as shown on drawing with screws All as directed by Engr in Charge

Locker Steel FD 1029 , Locker Steel DIMENSION Overall size shall be 760mm long 600mm wide and 1100mm high DESCRIPTION The locker shall be made of mild steel sheet 1mm thick 20 mm dia conduit pipe shall be chrome plated with wall thickness of 1 point 6 mm shall be fixed with side sockets Two handles chromium plated 100mm long shall be fixed to shutters with necessary riveting One hasp and staple 75mm long shall also be fixed to shutters with riveting The left shutters shall be provided with 100mm long tower bolt inside at upper and lower ends also The locker shall be provided with compartments as shown in drgs made of 1mm MS sheet FINISH All steel surface internally and externally exposed to view when placed in position shall be given two coats of green hammer paint internally and externally after properly smoothened the surface with sand paper and applying putty Powder coated Painting shall be done with spray machine All as directed by Engr in Charge

Rack 6 Tiers FD 1038 , Rack 6 Tiers DIMENSION Overall size shall be 915mm long 610mm wide and 1905mm high DESCRIPTION The entire rack shall be made of 1mm mild steel sheet The sides shall be provided with 40x40x4mm angle iron welded to 1mm thick MS sheet 75x75x3mm thick Flat iron cut to shape shall be welded at front corner All partitions shall also be made of 1mm thick mild steel sheet and shall be riveted to side of rack All Dimensions shape and size shall be followed as per drg All joints fixing shallbe done in accordance with standard specifications Rest all as shown on drg FINISH All steel surfaces exposed to view when placed in position shall be powder coated painted with two coats of silver grey paint internally and extrenally with spray machine after preparation of surfaces Painting shall be done with spray machine All as directed by Engr in Charge

Rack Laundary TP , Rack Laundary DIMENSION Over all size shall be of 900 mm long 310 mm wide and 1200mm high All wood shall be of first class teak wood The shutters of each compartment shall open towards top and slide into the depth of the rack laundary Three shelves equally spaced making four compartments shall be provided Two steel handles of 100 mm long shall be provided to each shutter of the compartment The locking device shall be provided to each compartment with duplicate key and each shutter shall be provided with decorative key plate FINISH All wood surface exposed to view when placed in position shall be French polished with lacquer finish rest All as directed by Engr in Charge

Recepticale with Bucket large FD 1044 , Recepticale with Bucket large Overall size shall be 420mm dia and 510mm high The body shall be of 1mm thick GI Galvanized Iron circular sheet of 405 mm dia Bottom of circular sheet body shall have 25mmX4mm flat iron band welded to 1mm thick circular sheet 95mmX50mm dia foot rest 3mm thick cut to shape shall be welded to 25mmX4mm flat iron lever whose fulcrum shall be in the centre of circular body supported by 25mmX3mm flat iron made to V shape and welded to circular sheet body in such a way that 6mm dia loose rivet shall be provided in centre to hold and support fulcrum The other end of lever shall be fixed to 25mmX4mm vertical lever hinged at bottom and top with 3 dia pin The top end of vertical lever shall be attached to mild steel reinforcement sheet of 175mmX100mm welded to cover to enable cover to open when the pressure shall be put on the top of foot rest at bottom lever Top cover shall be of 1mm thick GI sheet cover 420mm dia and bend inside cover 3mm dia wire alround the cover Two numbers brackets made to shape out of 3mm thick mild steel sheet as reinforcementsheet welded to cover enables the cover to open Bucket shall be made of 1mm thick GI sheet 340mm dia at top and 210mm dia at bottom Top of bucket shall have 2 numbers bracket 50mmX65mmX3mm thick flat iron welded to bucket for holding 10mm dia mild steel bar handle 40X3mm mild steel flat iron ring shall be provided at bottom of bucket 10mm dia mild steel bar handle shall be provided to bucket All steel surfaced except galvanized iron surfaces shall be given two coats of aluminium paint over a coat of primer after preparation of surfaces All as directed by Engr in Charge

Screen Movable with castor Wheel FD 83 M , Screen Movable with castor Wheel All as shown on drawing Screen movable shall be of three fold Middle span shall be 1200mm wide and the sides shall be equally spaced Over all size shall be 1650mm high and 2400mm wide frame shall be made out of 25mm dia conduct with wall thickness 1 point 6mm Six numbers ball bearing rubber castors of 50mm dia shall be provided at bottom as shown n drawing The frame shall be 50mm dia shall be provided at bottom as shown on drawing The frame shall be provided with hooks and wire springs for curtains Curtains shalbe cotton 180GSM and good quality shall be provided to screen movable All steel and iron surfaces exposed to view when placed in position shall be given two coats of enamel paint of white colour, over a coat of primer after preparation of surfaces as directed by GE painting shall be done with spary machine All as directed by Engr in Charge

Side Rack With Trays FD 1023 , Side Rack With Trays DIMENSION Overall size shall be 840mm long 355mm wide and 810mm high DESCRIPTION Four mild steel angle iron 40mmx40mmx3mm shall be provided as legs and shall be 810mm high The middle shelf shall be equally spaced between top and bottom shelves The thickness of sheet shall be 1mmTop shelf shall have three compartments or spaces equally spaced with 50mm high partition and back covering with mild steel sheet 1mm thick FINISH All steel surfaces exposed to view when placedin position shall be given two coast of powder coated paint over a coat of primer after preparation of surfaces Painting shall be done with spray machine All as directed by Engr in Charge

Sofa Set 4 Seater FD 281 , Sofa Set 4 Seater All as show on drawing DIMENSION Overall size of one Seat shall be 670mm long and 745 mm wide and 530mm high up to arm rest level DESCRIPTION The sofa set four seater shall consist of four single seats All wood shall be of first class teak wood MP Legs of sofa set shall be 70mm x35mm in section teak wood Front legs shall be jointed by 100mm x 35mm in section wooden rail in front Front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides 100mm thick seat cushion and back cushions shall be of size 530mm x 560mm one numbers in seat and one numbers in the back The cushion shall be of cool foam or any other superior quality foam of 40 density as approved by Engineer in charge Cushion shall be covered with approved color tapestry cloth approved by GE not less than Rs 450 meter or as directed by Engineer in charge FINISH All wood surface exposed to view when placed in position shall be French polished with lacquer finish

Sofa Set 5 Seater FD 281 , Sofa Set 5 Seater DIMENSION Overall size of three seat piece shall be 1730mm long 745mm wide and 530mm high up to arm rest level Overall size of one piece shall be 670mm long and 745 mm wide and 530mm high up to arm rest level DESCRIPTION The sofa set to seat five shall consist of one large three seat piece and two small one seat pieces All wood shall be of first class teak wood MP legs of sofa set shall be 70mm x35mm in section teak wood Front legs shall be jointed by 100mm x 35mm in section wooden rail in front Front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides 100mm thick seat cushion and back cushions shall be of size 530mm x 560mm three numbers in seat and three numbers in the back for the large seat In one seat sofa chair the cushion shall be one in back and one in seat of size 530mm x 560mm The cushion shall be of cool foam or any other superior quality foam of 32 density as approved by Engineer in charge Cushion shall be covered with approved color tapestry cloth approved by GE not less than Rs 450 meter or as directed by Engineer in charge FINISH All wood surface exposed to view when placed in position shall be French polished with lacquer finish rest All as directed by Engr in Charge

Stool Steel 3 feet high FD 81 , Stool Steel 3 feet high DIMENSION The overall height of the stool shall be 900mm after lift DESCRIPTION It shall be of revoloving type with 360 degree swivel The frame shall be of round pipe 1 inch dia and the frame and base shall be of chrome plated The stool shall have gas lift and consist of foot rest The seat shall be of soft cushion 50 mm thick fitted with best quality tapestry leatherite cloth All as directed by Engr in Charge

Stool Steel adjustable Revolving D 1026 , Stool Steel adjustable Revolving All as shown on drawing Overall size shall be 455mm dia and 600mm high four legs of 25mm dia mild steel sheet pipe legs made to shap of thickness 1 point 6mm irrespective of what is shown on drawing 12mm dia mild steel bar ring shall be provided at 150mm from bottom joining four legs as showon drawing Two cast iron discs shall be provided at top of legs and at 100mm top of legs as shown on drawing and fixed to legs with 6mm dia bolt 25mm dia threaded steel bolt 255mm long fixed with 6mm thick steel plate 100mm dia and top of 25mm dia threaded bolt shall be provided as shown on drawing the padded seat shall be fixed on 6mm thick 100mm dia steel plate with scren for which four nubmber holes are provided in steel plate Padded seat shall be 38mm dia The bottom of padded seat shall be 30mm soft wood over which a layer of coir shall be provided to give proper shape as shown on drawing Hessian cloth shall be provided to cover the layer of coir and under the soft wood padded seat A layer of cotton shall be provided and covered with Rexene cover alround the top and bottom to form the padded seat All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer after preparation of surfaces Hard rubberPVC toes shall be provided to the bottom of legs

Table 3 feet x 2 feet with Drawer FD 283 , Table 3 feet x 2 feet with Drawer All as shown on drawing Overall size shall be 900x600x760mm Steel frame shall be 800mmx500mmx742mm Four legs shall be of 25 SQ mild steel tube of wall thickness 1 point 6mm top of Legs shall be joined together with 25mm squre mild steel tube of wall thickness 1 pont 6mm top rails on long and short sides Two short stiffner joining legs in short sides at 100mm from bottom shall be provided in the middle of short stiffner joining short stiffners with 25mm squre mild steel tube of wall thickness 1 point 6mm at 100mm from bottom of legs A drawer on left side of table near top stiffner shall be provided of size 350mmx130mm and 500mm deep with locking arrangement and recessed handle Mild sttel sheet used for drawer shall be of 1mm thick top of table shall be of 18mm thick pre laminated particle board with teak veneer shade of 6mm teak wood edging al round the top of table irrespective of what is shown and specified on drawing PVC Hard rubber toes shall be provided to the bottom of legs All steel surfaces exposed to view when placed in position shall be paited with two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces

Table Center Brass with Glasss Top FD 375 , Table Center Brass with Glasss Top Overall size shall be 1200mm long 600mm wide and 400mm high Legs shall be of 40mm dia anodized brass legs four in number in one piece The legs shall be joined in short and long sides with two number 25mm dia brass pipes of wall thickness 2mm The top pipe shall be fixed 150mm from top and the lower pipe shall be at 100 from bottom of top pipe The brass frame shall be 900mm long and 450mm wide Vaacuum rubber sho shall be provided at top of legs which shall be closed with brass sheet 1 point 6mm thick The bottom of legs shall be covered with brass sheet of 1 point 6mm thick sheet The bottom of legs shall have PVC shoes The top shall be 10mm thick plate tinted glass white colour with corners rounded as shown drawing the edges of top of table shall be rounded off All as directed by Engr in Charge

Table Center 2 tire FD 393 , Table Center 2 tire DIMENSION Overall size shall be 900mm long 450mm wide and 400mm high DESCRIPTION All wood shall be of teak wood Top of the table shall be of 18mm thick MDF board of approved shade with 4mm thick teak wood beading all round the edges of top Legs shall be made out of 60mmx30mm in section teak wood and 356 mm high Bottom rail of teak wood of 20mmx50mm in section and 420mm long shall be provided between legs widthwise at 100mm above the bottom of legs The bottom tier shall be fixed on the top of bottom side rails with 50mm long screwss The bottom tier shall be of 18mm thick MDF board exterior grade of approved shade with 4mm thick teak wood beading allround the edges of both the tops 25mm dia hard rubber PVC rings shall be fixed to the bottom of all legs fixed with 30mm long screws All as directed by Engr in Charge FINISH All wood surfaces shall be French polished with high gloss finish

Table Office Clerk Steel FD 1004 , Table Office Clerk Steel DIMENSION Overall size shall be 1200mm long 610mm wide and 760mm high DESCRIPTION Steel frame shall be of size 1160x570x742mm four legs of 25mm mild steel tube of 1 point 6mm wall thickness shall be provided Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1 point 6mm in long and short sides Two short stiffeners of same size shall be provided at 130mm from bottom of legs One long stiffener shall also be provided to the middle of short stiffeners Three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deepThe top of table shall be provided with MDF board of 18 to 19mm thick with teak veener shade and 4mm thick teak wood edging alround the table Hard rubber PVC toes shall be provided to the legs Locking device shall be provided to drawers FINISH All steel surfaces exposed to view when placed in position shall be powder coated painted with two coats of silver grey paint internally and extrenally with spray machine after preparation of surfaces Painting shall be done with spray machine All as directed by Engr in Charge

Table Computer MAP FD E6 MAP 03 , Table Computer MAP DIMENSION Overall size of top shall be 900mm long 561 point 20 mm wide and 750mm high DESCRIPTION All MDF board used in manufacturing of top shelves drawers tray shall be of 18mm thick MDF board The frame of table shall be of 25MM square pipe of wall thickness not lss than 1 point 6mmThe top of table shall be provided with 4mm thick teak wood beading The legs shall be made out of 25mmx50mm MS rectangular CR pipe of 18 guage Each leg shall be provided with rectangular PVC cover made to shape on front sides only The drawers shall be provided with telescopic channel 300mm long The legs shall also be provided with nylon buffers FINISH All wood surfaces shall be French polished with high gloss finish All as directed by Engr in Charge

Table Office Officer Stee FD 1003 , Table Office Officer Steel DIMENSION Over all size shall be of 1680x870 x760mm DESCRIPTION 25 mm MS square tube 1 point 6 mm thick shall be provide to frame 1 mm thick MS sheet nominal all around for drawer Top shall be of 18mm thick MDF board ISI mark exterior gde one side decorative finish approved by GE and 4 mm thick teak wood edging all around shall be provided for top Three drawers shall be provided on right hand sides of table A cupboard with front openable door shall be provided on the left side of the table A shelf shall aslo be provided at the middle of cupbaord All sheet for drawers shelf and cupboard and back covering shall be 1mm thick Hard rubber shoes shall also be provided to the bottom of legs Rest all as per drgs FINISH All steel surfaces exposed to view when placed in position shall be powder coated painted with two coats of silver grey paint internally and extrenally with spray machine after preparation of surfaces Painting shall be done with spray machine All as directed by Engr in Charge

Table office executive desk TP , Table office executive desk Table office executive desk over all size 1350x750x750mm ERU 1200x450x750mm Back unit 750x425x750mm Mobile pedestal 390x435x529mm All as directed by Engr in Charge

Table Peg FD 384 , Table Peg DIMENSION Overall size shall be 450mm long 300mm wide and 380mm high DESCRIPTION Legs shall be of teak wood of section 30mmx50mm The legs shall be 362mm high 5mmx5mm in section groove shall be provided on the top of legs which shall be visible when placed in position Two nos top rails of section 20mmx40mm of teak wood shall be provided connecting legs Two bottom rails of size 20mmx40mm shall be fixed between the legs A centre stiffeners of size 20x40mm shall be provided at centre of side bottom rails for extra support irrespective of what is shown on drg Top of the table shall be of 18mm thick MDF board with 4mm teak wood edging all round the top of table FINISH All wood surfaces exposed to view when placed in position shall be french polished with high lacquer finish All as directed by Engr in Charge

Table Stainless Steel FD 131 M , Table Stainless Steel All as shown on drawing Overall size shall be 2100mm long 900mm wide and 760mm high Steel frame shall be of 2000mm x 800mmx759mm Six legs shall be of 25mm square mild steel tube of wall thickness 1 point 6mm joined together at top with top rails in long sides with 25mm square mild steel tube of wall thickness 1 point 6mm Three flat iron equally spaced shall be of 50mmx3mm and shall be welded to top rails as shown on drawing Three short stiffeners at bottom at 100mm from bottom shall be provided joinng legs in short sides Long stiffener joing short stiffeners in the middle shall be provided at 100mm from bottom with 25mm square mild steel tube of wall thickness 1 point 6mm Hard rubber PVC toes shall be provided to the bottom of legs Top of table shall have 1mm thick stainless steel sheet at top made to shape all as shown on drawing All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of surfaces except on stainless steel surfaces All as directed by Engr in Charge