Hapur Pilakhua Development Authority Tender

S/E of over head line with suitable size ACSR conductor on pole including binding etc all complete. (i) ACSR Racoon SOR NO.-627/18

B-LT

S/E of 8.5 mt. long PCC pole support grouted in 1:4:8 (cement fine sand CC) including 30 cm high plinthing from ground level with the cost of all material lab. T&P etc required for proper completion of work or as direction of E/I. (A.R. 2022)

S/E of strud stay with 8.5 mtr. Long PCC pole grouted in 1:4:8 cement fine sand & OBB mixture etc all complete. (A.R. 2022)

Supply and erection of stay set at least 3.5 metres away from the pole complete with galvanised 19mm dia. x 1.80 meter long stay rod, 30cm x 30cmx6.3 mm anchor plat, thimble stay clamps, stay insulator, 19mm x 600mm double serew tightener, 7/3.15 mm G.I. stay wire etc. in 1:3:6 cement concrete in all respect of E/I. SOR.No-631/18

S/F of suspension clamp suitable for hanging of various size ABC conductor on pole etc all complete as required. (A.R./2018)

S/E of 150sqmm X 3 C + 1 x 120 sqmm + 1 x 16sqmm XLPE insulated ABC bare messenger wire etc complete as per direction and approved by E/I. (A.R. 2018)

S/Fof pole mounted type CMS TPN distribution box Sintex size 400 X 300 X 190 MM & 4 Nos. 40 X 50 mm aluminium bus bar with ingress protection to IS 8623 cable entry from bottom & /or sides shockproof & rustproof, suitable for polluted atmostpheres were high working tempreture & higher arc resisteance witherproof & maintenance free complete with supporting clamp i/c locking arrangement & painting etc complete as per direction of E/I. (A.R. 2022)

S/F of 2.5mt. long 20mm dia MS earth rod with 6 SWG GI earth wire, nut, bolt & washer etc all complete.(A.R. 2022)

(C) Sub Station

S/E of Double pole stucture ( FOR POLE / PLINTH MOUNTED TRANSFORMER TYPE SUBSTATION )12mt. long 410 SP-62 ST pole (259 Kg) support grouted in 1:3:6 (cement coarse sand 6 graded stone aggregate 40 mm nominal size) including 30 cm high plinthing from ground level with the cost of 3 no 100 x 50 x 6mm 2.24 Mr long Chanel and 3 no. 75 x 40 x 6mm 2.24 Mtr lon Chanel and With D.O. Fuse set , T.P.M.O. switch , anticlimbing device and paintig of pole Complete with all material lab. T&P etc required for proper completion of work or as direction of E/I. (A.R. 2022)

Const. of T/F plinth size 1.5x1.5 & height over all 1.30 mt. made of 1st class B/W in 1:4 ( 1 cement & 4 coarese sand ) in foundation 100 PCC in 10:5:1 & top of the plinth 100 mm PCC in ratio 1:2:4 ( 1 cement 4 coarse sand & 4 stone ballast agreegate 4cm ) complete with 12mm Plaster all side and white Wash etc as per direction of E/I (A.R. 2022)

Const. of feeder pillar plinth size 1.50 x 0.58 mt & Height 0.45 mt with 1st class B/W in 1:4 in foundatio 100mm PCC ratio 10:5:1 and on top 100m PCC in ratio 1:2:4 ( 1 cement 4 coarse sand & 4 stone ballast agreegate 4cm ) including plaster & white wash etc all complete. (A.R. 2022)

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at a depth of 750 mm. below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. SOR/2018 ( make- gloster / havells / universal / polycab )

(i) 400 sq mm 3.5 core 501(t) (1X2X30)

(iii) 185 sq mm 3.5 core SIN-501(q)

(vi) 10 sq mm2 core SIN-501(i)

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge.PWD SOR 504/2018

400 sq. mm

185 sq. mm

10 sq. mm

Supplying and fixing of light class G.I. pipe of 100 mm dia.(nominal) 3 metres length along the pole for protection of under ground cable as required. DSR 2022/SI NO. 12.39 (4907-16.16%= 4114)

Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel out door type TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and nstrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in- Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fusesetc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board (Out door type) shall be destal type for Cat-B and C only. SOR NO, 805 - 2 x 1017, 181390 - 2620 = 178770 /2018 (C) Incoming 630 AMP TPN -1 No.

Outgoing (I) 200 AMP TPN-2 NO., 100 AMP TPN -1 NO.

Supply and fixing of 2 metres high cage fabricated with 3 mm thick expanded metal fixed on 50 mm x 50 mm x 6 mm angle iron frame having vertical members spaced at 1 to 1.25 mts. and horizontal members spaced at 1mt. The vertical members shall be grouted in floor and horizontal members in the wall to a depth of 300 mm with ends forked. The cage shall have 2000mm x 1000mm size one leaf door with locking device having door frame fabricated with 35mm x 35mm x 6mm angle iron and 3mm expanded metal duly fixed with the cage member with hinge etc. the cage shall be painted with red oxide primer and synthetic enamel paint. The job includes all materials, labour T & P etc. for proper completion of work. complete as per direction of E/I.SOR.No-1142/18

Const. of fencing plinth clear inner size 4.5 x 7.0 x 0.45 mt. in 1st class B/W including plaster & providing M -150 Brick on edge floor laid dry joint sand filing including perpration base to proper slope..all complete in open space or as direction of E/I. . (A.R. 2022)

Supply and burying earth electrode for lightning conductor of 900mm x 900mm x 6.0 mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia. G. I. pipe for watering funnel, 30 cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal / coke and salt at least 150 mm thick alround etc. as per directions of E./Ic. complete in all respect. SOR NO.-707/18

S/F of PG clamp/connector suitable for connecting of various sizes ABC cable including insulating cap etc complete as per direction of E/I.. (A.R. 2018)

Supply, Installation, Testing and commissioning of 400KVA 11/0.433kv Aiuminium/copper wound distribution T/F Level-1or 2 Rating complete as per UPPCL specification etc all complete (A.R. 2023)

S&F of 32 Amp. 240 V DP metal clad rewireable type switch fuse unit on M.D.F.E.G. / Teak wood board complete in all respect.PWD SOR 305/2018 ( make - L&T / siemens / havells )

Supply and fixing of LED street light fitting having die cast aluminium body and diffuser/reflector with driver set suitable for 45 watt. Confirming to IP 66 protection complete in all respect. SOR No. 1421 CAT - AAA /2018 ( make - philips/ crompton/ bajaj / havells)