Gorakhpur Development Authority Tender

Concrete with 4.00cm gauge brick ballast, fine sand of 1.25 fineness modulus and cement in the proportion 8:4:1 in foundation and under floors including supply of all materials, labour and tools and plants etc. required for the proper completion of the work. (S.I.No-275)

M-150 class brick work in 1:4 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. (S.I.No-305+309+310)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm (D.S.R. No-11.41.2)

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. (DSR NO -8.9.1.1)

Supply and fixing of flush Doors commercial quality conforming to I.S. 2202 Part I (1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts locks handles springs fitting with necessary screws to be supplied departmentally. (ii) 35 mm thick

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) INCLUDING SHUTTRING AND CENTERING

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars (D.S.R. No-5.22.1)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m²

Mild steel or iron work in heavy sizes such as trusses,builup gates, record racks etc. wrought to required from including drilling holes, rivetting or welding where necessary, and also including supply of steel, bolts, nuts, etc and their fixing required for proper completion of work

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

SS KITCHEN SINK

New Toilet Block &Urinals

Construction of urinals for 3 as per standard including supply of all materials, labour and T&P etc. required for proper comPletion of the work with tiling upto height 1.5m As per CPWD as on 01.04.2021

Internal water supply & sanitary installation including supply of all materials, labour and T&P etc. required for proper comletion of the work. @10%plinth area rate.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR NO-19.32.1

Boundary Wall & Gate

Apply priming coat over new steel and other metal surface after and including preparing the surface throughly cleaning oil grease dirt and other foreign matter and soured with wire brushes, fine steel/ wood scrapper sand papering and knotting including cost of all materials, labour and T & P etc. required for proper complition of work.

GATE 1

GATE 2

GRILL

Apply painting first coat over primimg coat on steel and other metal surface after and including preparing the surface throughly cleaning oil grease dirt and other foreign matter and soured with wire brushes, fine steel/ wood scrapper sand papering and knotting including cost of all materials, labour and T & P etc. required for proper complition of work. SOR-2 (PAINTING NEW ITEM)

GATE 1

GATE 2

GRILL

Mild steel or iron work of small sizes and sections such as door frame holding down bolts, hold fasts, Tie rods gratings etc. (when not including in over all rates) wrought of required from including supply of steel bolts and nuts, and wastage etc. and their fixing labour and Tools and plants required for the proper completion of the work.

Interlocking

Providing and laying of 1 Shaped mechanically compressed Interlocking cement Concrete block pavement having thickness 80mm Manufactured by high pressure & controlled vibration machine of OPC cement mixed with 25% marble powder with minimum 5mm thicktopping, having compressive strength not less them 30MPa including cost of all material, labour, T&P leveling and dressing of surface to required level and slope, spreading and, moisting 30mm, thick local sand including filling joints for proper completion of the work including all type of taxes, T.T. etc. as per drawing and Technical specification,

Dismentaling

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm DSR-15.23.1

Dismantaling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the engineer incharge within distance of 60 mtr. SOR -692

Dismantaling door & window, including chowkhats, with hold fast & including stacking of materials as directed by the engineer incharge within distance of 60 mtr. SOR- 703

Dismantaling Exsisting plaster including stacking of materials as directed by the engineer incharge within distance of 60 mtr. SOR- 706

Dismantaling RCC & RBC including stacking of materials as directed by the engineer incharge within distance of 60 mtr. SOR- 694

Landscaping (Approx)

Electrical

Wiring for light point/ exhaust fan point/ call bell point with 1.5 sq. mm.FRLSH PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq. mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group A, (D.S.R. No-1.8.1)

supply and fixing following piano type Switch/Socket on the existing switch box/cover including connection etc.., as required.

3 pin 5/6A Socket outlet (D.S.R. No-1.23.4)

6 pin 15/16A Socket outlet (D.S.R. No-1.23.5)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate as required. (D.S.R. No-1.25)

Supplying and fixing following way, single pole and neutral, Sheet steel, MCB distribution board, 240V on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar,din bar, interconnections, powder pointed including earthing etc as required.( But without MCB/RCCB/isolator)8 way, Double door (D.S.R. No-2.3.2)

Supplying and fixing 5A to 32A rating 240/415V, 10KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc.., as required.Double pole, 32A (D.S.R. No-2.10.3)

30 W LED Light - Tube light (Phillips/Havels/Wipro) (MR)

FAN - Celing (48 Inch High Speed) (MR)

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 Watt. Confirming to IP 66 protection complete in all respect. CAT- AA (S.O.R. No-1421)

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required. (D.S.R. No-2.1)

32A TP&N(D.S.R. No-2.1.1)

2X2 FALSE CEILING LIGHT (MR)