Directorate Of Urban Local Bodies Tender

Disposal of earth up to 8.00 Km from site including etc. all complete work. S.I.N0-231(A)

Earth Work in Embankment (lead upto 8 km) in ordinary soil excavation to be in the form of regular pits not exceeding 0.50 m in depth earth work in embenkment to in 20 cm layers including remming and dressing the surface to required levels and slops also including 1.50 m lift and 30 m lead. The earth form cutting to be used in making in embekment or to be disposited and spoil banks with in 30 M. distance as directed by the engineer in charge etc all complete as per the direction of engineer in charge. RMR

M-150 Brick work in 1:4 one cement and four course sand mortar in foundation and plinth Including suppy of all material labour,T&P etc required for proper completion of the work S.I No 305(a) SOR-2022

S/L 12 mm thcik plaster (1:4) with cement & coarse sand including all materials,labour,tools, & plant etc all completed as per the direction of engineer -in - charge.SOR 2022 S.I N0-584 New item

S/L of 22.4 to 53 mm gauge stone ballast with stacking for measurement etc all complete as per direction of engineer in charge.( As per PWD SOR 2020 RMR)

Consolidation stone aggregates of 45-63mm/22.4-53mm size to water bound macadam,specification including spreading in uniform thickness hand packing rolling with three wheel 80-100 KN static roller in stages to proper grade and camber applying and brooming crushable screening to fill-up the interstices of coarse aggregate,watering and compacting to the required density Grading 2/3 as per Technical Specification Clause 405.SOR 2022 Page N0-51 (752)

S/L P:C:C ( 1:4:8) with 40 mm size stone ballast coarse sand & cement etc all complete as the direction of engineer in charge (AS PER PWD SOR 2022 PAGE NO 18 SI NO 5.11 ITEM NO 281.)

Construction of un-reinforced dowl jointed at expansion and construction join only plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M 30(Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 jmm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and construction joints, applying debonding strips, primer, sealant, approaches near to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days,using Curing compound (where specified) and water finishing to lines and grade as per drawing and finished with Power Trowel Cum Floter-Trimix Flooring Machine.Technical Specification Clause1501

Supply & laying 80mm thick precase cement concrete i-sape interlocking paver block (Grey color) with top layer of minimum 8mm thickness having plan dimension 200x(160+120mm) of O.P cement smoothing gloss finish,skid resistant manufacture from rubber moulds through vibro-compression mechanism, the compressive strength of concrete paver block shall not be less than 30mpa (M-30) and weight 5kg. per no. confirming to IS:15658-2006 including cost of material, labour,t&P etc. required for proper completion of the work as directed by Engineer-in-charge RMR

RCC work with cement, approved coarse sand and 2 cm gauge stone grit in proportions of 1:1.5:3 in slab wall etc excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 BWG G.I.binding wire and including necessary centering and shuttering etc and supply of all materials, labour and tool & plants etc. required for proper completion of the work including cost of binding wire. The rate excludes making of drip course which shall be paid extra. But for Slabs (As per S.I.No. 283 a) SOR-2022 New item

S/F M:S (tor steel or plain) in plain work such as R:C:C or R:B work including bending for proper shape as necessary including bending for proper complition of the work and including supply of all steel & wasteage, bend, hooks, and authorised overlappinf shall be measured etc(Labour rate only but including cost of binding wire) all complete S.I.No. 502 SOR 2022

P/F in position pre-cast R.C.C.manhole cover and frame of required shape and approved Quality and Circular shape 560mm internal diameter

GST