Directorate Of Urban Local Bodies Tender

CCMS PANEL - Supply & Fixing of CCMS Panel is suitable for Outdoor application with IP65 protection made up of MS 16 gauge for outdoor type Distribution Panel for 415V, 1 Phase, 4Wire 50 Hz AC. CCMS panels offer Group ON/OFF Control, Metering "The Smart Lighting Control Panel is capable to capture (a record) and provide the following parameters: Voltages Current Power Factor Active Power (kW) Apparent Power (kVA) Metering kwh " Number of hours the power supply was unavailable The lighting Control Panel can switch ON and OFF the lights of a particular switching point remotely or automatically throughout the year on basis of sunrise and sunset time. "Smart Lighting Control Panel is capable to generate alert SMS for: Phase-wise currents on crossing threshold values Phase-wise voltages on crossing threshold values MCB trips Theft alerts Group failure of lights No output supply" "The system monitors all the following from the Smart Lighting Control Panel: Voltages each phase Current each phase PF each phase Metering kwh A further system is able to indicate various faults Failure of contactor High /low voltage Overload on the phases" Settable data update interval from 1 minute to 15 minutes. Communication Protocol - RTU supports RS485/RS232 MODBUS communication RTU Schedule the CCMS on/off based on the remote configuration from the software. Flexible control options to configure on-off schedule as, o Instant Mode – Immediate ON-OFF with software and mobile application Instant Auto Mode – Immediate ON-OFF with software and mobile application up to next auto time. Fixed Mode – User defined ON and OFF timing Astronomical Mode – Automatic scheduling based on sunset and sunrise timing UV (Under Voltage) – OV (Over Voltage) Protection is required. The device will turn off all relays when the input voltage is less than the UV threshold or greater than the OV threshold. UV, and OV thresholds will be configurable from software. Electrical parameters to be synced with software as per user-defined sampling time. Electrical parameter sampling timing to be configurable from 1 minute to 30 minutes via user interface. The device will have the ability to store electrical parameter data for last 6 weeks at interval time of 1 hour and sync it with software. However, interval time to store data in device memory while no network condition will be configurable from software. The device will store events like power-up & relay on-off and sync it with software. The device will have the provision to connect to the internet via GPRS technology. The device will be designed modular in such a way that it can be upgraded to 4G or higher technology without complete replacement. For GPRS connectivity device will have an easily accessible sim card slot and antenna connector. (Sim & 5 Year recharge) Provision to update device firmware remotely through software. The device shall have provision to connect the door switch. Cluster Meter along with Remote Terminal Unit (At Central Control Panel Unit) "The metering unit should support the following measurements for the cluster (circuit) a. Voltage b. Current c. Active Power d. Apparent Power e. Cumulative KWh f. Cumulative KVAh g. Power Failure On/ OFF events Record Following Events occurrence and restoration a. Over Voltage in each Phase b. Under Voltage in each Phase c. Over Current / Over Load in each phase d. Door Open The threshold value can be configured from Central Management Software controller unit shall capable to switch ON/OFF lamps phase-wise after getting command from the central control station instantaneously OR Automatically throughout the year on basis of the astronomical clock OR As per Pre Defined scheduler" Cluster Energy Meter shall measure the consumption of cluster irrespective of maintenance or actual lighting cycle. Cloud System: All The data from the Real Time System will be stored in the Cloud System in every 1-60 min, which can be adjustable by the user. By using the web server and the connection with Cloud, all the data will be seen by the user at any point of time. We can remove the data from the cloud server as per our usage, we can take the backup from the Server to our HDD to save the cost of storage in the cloud ENERGY METER The lighting Control Panel have a 3- phase meter display for measuring all the parameters , Complying IS 13779, Energy meter is required to get the electrical parameter and RTU fetch the same data which is accessible on Web UI. • Class 1.0 • phase 4 wire whole current type • 10-60 A • 50 Hz

Chapter -2 / Earthing - Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 microns filled with the crystalline conductive mixture (CCM) having anti-corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with a good mixture of retaining capacity and one earthing lead of 25mm x 5mm G.I. strip up toto switchboard (from the apron to switchboard, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing. The result of earthing should not be more than one Ω (ohm). Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. (UPPWD SOR ; 2018-725(B)

Supply and laying 25 mm x 3 mm GI Strip on the surface or in recess for connection up to CCMS panel (UPPWD SOR ; 2018-716)