Cane Development And Sugar Industry Tender

ANTITERMITE TREATMENT Providing and injecting chemical emulsion for preconstruction antitermite treatment and creating and chemical barrier under and around the columns pit, wall trenches basement excavation top surface if plinth filling junction of wall and floor along the external per meter of building expension joints surrounding of pipes and conduit etc. complete (Plinth area of the builling at ground floor only shall be measured as per I.S.6313(part ii 1981). Aldrine emulsificable concentrate of any other approved material such as hepthachlor or chlordance will be used . The rates of application of chemical emulsion shall be as follows. CHAPTER-8 NEW ITEM

Damp Proofing Coarse 4cm Thick and cement Concrete consisting of 1 part cement and 2 part approve Coarse sand and 4 parts approved 13mm(1/2inch) graded stone grit and including water proofing material as ordered by the engineer-in-charge in the proportion as specified by the manufacturer. S.O.R 361 C

PCC Work Cement concrete with 4cm gauge approved stone, ballast approved coarse sand cement in the proportion of 1:4:8 including supply of all material , labour and T&P etc. required for proper completion of the work. S.O.R-281

R.C.C In Foundation R.C.C Work with cement approved coarse sand and 2 cm gauge approved stone grit in proportion of 1:2:4 in R.C.C raft and foundation and footing with 4cm gauge stone ballast excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I Binding Wire and including necessary Centering and Shuttering etc. and supply of all Material, Labour and T&P etc. required for Proper completion of work. Binding wire to be supplied by the contractor free of cost. Including making of drip coarse. S.O.R-287

R.C.C In Lintel Beam R.C.C Work with cement approved coarse sand and 2 cm gauge approved stone grit in proportion of 1:1.5:3 in lintel of door, windows and sunshade excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I Binding Wire and including necessary Centering and Shuttering etc. and supply of all Material, Labour and T&P etc. required for Proper completion of work. Binding wire to be supplied by the contractor free of cost. Including making of drip coarse. S.O.R- 283A

R.C.C In Column Work R.C.C column in 1:1.5:3 S.O.R- 289

R.C.C In Roof Beam as item no. 283A above but in lighter beam having spans upto 6M S.O.R- 285

R.C.C In Slab R.C.C for Slab in the Proportion of 1:1.5:3 284A

Mild Steel Work Mild Steel or TMT Bars (Fe-500 D grade or Higher) or HYSD Bars or Iron in plain work such as Reinforced concrete or Reinforced brick work (when not included in an over all rate ) brough to required shape as necessary including bending for proper completion of the work and including supply of all steel. S.O.R- 504

Brick Work in Foundation First class brick work in 1:6 cement & coarse sand of 2.20 FM morter in foundation and plinth including supply of all matterial labour T&Petc.Required for proper completion of the work. As/ Analysis

230THK Brick Work in Super Structure Frist Class Brick work in 1:6 Cement & coarse sand Mortar in superstructure, including necessary cutting and moulding of brickwork as required, the wall thickness one brick thick. As/ Analysis

Plaster on Internal Wall 12mm thickplaster with cement and coarse sand of 2.20 F.M.in (1:6) labour far taking and washing.over brick work minium thickness not to be less then 10.00mmthick.including supply of all materials labour T&P etc.Required for proper completion of the work. SOR-13.4.2 LUCKNOW

Plaster on External Side 15mm Thk Cement Plaster on Rough Side of Single or Half Brick wall Mix in 1:6 (1 cement :6 Coarse sand). SOR-13.5.2 LUCKNOW

Forming Grooves of Uniform size from 12x12 and upto 25x15 in plastered surface as per approved pattern using wooden battens nailed to the under layer including removal of wooden battens, repair to the edges of plaster panel and finishing the groove complition as per specification and direction of Engineer-in-Charge. S.O.R MOD. PG 37

Putty Work Providing wall Putty on New surface with approval quality material of berger/J.K./Birla or Similar make 2 coats. S.O.R PAGE- 43

Painting Work Distempering one coat with Oil Bound distemper of approved brand and manufacture and required shade on undecorated wall surface with an even shade over and including a primer coat with cement primer of approved brand and manufecture such as of British," Shalimar asian paint after throughly brushing the surface free from mortar dropping and other foreign matter and alsoo including preparing the surface even and sand prepared smooth including cost of all materials. S.O.R- 649

As in Item No. 649 above but for every coat after the first Coat. S.O.R-650

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) S.O.R Lucknow-13.47.1

Tile Wotk Supply and fixing 6 to 8 mm thick ivory or Light shades Vitrified tiles of standard make 600 x 600 mm size in Flooring and Skirting with 1:3 approved cement and coarse sand mortar finished with in its cement color slurry, jointing and polished of approved quality complete including supply of all materials labour tools and paints etc required for proper completion of the work as per direction of engineer-in-charge. S.O.R New Item 05- page-40

Wall Tiles Supply and fixing 6mm thick China Glazed tiles of First quality on wall Laid With 1:3 approved cement and coarse sand mortar finished with white cement slurry, jointing and polishing complete including supply of all materials, labour and T&P etc. required for proper completion of the Work. S.O.R 628

Kota Stone Laying of 25mm Thick Kota Stone of size 45x45cm and above flooring over previously prepared base with 2cm thick 1:3 cement and sand mortar including filling of Joints with Cement mixed with pigment required for matching the shade of floor as per the direction of Enginner-in-Charge including cutting polishing with wax polish including supply of all materials, labour and T&P etc. required for proper completion of the work. Chapter -14 New Item 2 Page- 40

Door Frame Providing and fixing factory made uPVC door frame made of Upvc extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge Extruded section profile size 42x50 mm (Rates Without Gst and labour Cess) D.S.R 9.117.2

Upvc Windows Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to Upvc profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). (Rates Without Gst and labour Cess) S.O.R. Lucknow 9.147D2

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (Rates Without Gst and labour Cess) D.S.R. 9.20.1

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. (Rates Without Gst and labour Cess) S.O.R Lucknow 9.84

Providing and fixing brass 100 mm mortice latch and lock with 6 levers without Pair of handles for aluminium doors including necessary cutting and making good etc. complete. Addition as per S.O.R Item no. 21.12.2 Powder Coated minimum thickness 50 micron aluminium tubular handle bar S.O.R Lucknow 21.13+21.12.2

Brick Coba PROVIDING AND LAYING " Brick Coba" 12mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15mm to each other, over 20mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compond spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30cm x30cm and side wall parapet shall be rounded by brick ballast cement and coarse sand masonary Coba with acetic water proofing compound @ 2% by weight & including S/o all material , labour T&P etc, complete for proper completion of work. S.O.R- NEW ITEM NO.3

MS GRILL WORK FOR WINDOW Apply primer coat and two coats of superior synthetic enamel paint of standard make brushing to give an even shade and finished and including cleaning the surface all dirt dust and other forein matter sand paparing and stripping including cost matter and scoured with wire brushes fine steel / wood scrappers sand papering and knotting including coats of all and supply of all material labour and T&P etc. required for proper completion of work. S.O.R new item 1+2+4 page no. 42

Mild Steel or iron work of small size and section such as holding down bolts, hold fast, tie roads , gratings etc wrough to required form including of supply of steel, bolts, nuts and wastage and fixing of fabrication of grill and staircase.

WATER PROOFING Providing and laying watter proffing Treatment in Sunken portion of WS, Bathroom Etc. By applying cement Slurry Mixed with water Proofing cement compound Consisting of applying. Ist course of applying cement slurry @ 0.488 kg/sqm mixed with water proofing cement compound @0.253 Kg/Sqmt. This layer will be allowed to air cure for four Hours. second layer of slurry of cement @0.242 Kg/Sqmt mixed with water proofing cement Compound @ 0.126 kg/Sqmt. This layer will be allowed to air cure for four Hours. Followed with water curing for 48 hours. The rates includes prepration of surface, Treatment and Sealing of all joints, Corners, Junctions of Pipes and masonary with Polymer Mixed Slurry. S.O.R Lucknow 22.5

Armstrong False ceiling FALSE CEILING ARMSTRONG FALSE CEILING :-Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5mm thk tapered edge gypsum moisure resistant board 12.45.3

Collapsible Shutter Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. PWD -518

SITE DEVELOPMENT SITE CLEANING Clearing Jungle including up rooting of rank vegetation grass, bush, wood, trees and sapling of Girth upto 30 cm measured at a height of 1mt. Above ground level and removal of Rubbish Upto a distance of 50mt. Outside the periphery of area Cleared. S.O.R 259

As item No. 259 but clearance of grass (A)

EARTH FILLING Ordinary Soil & Cartage of Excavation earth from distance of 5km.(Analysis of 5.0 km carted earth) Analysis attached

Interlocking Tiles Supply & Fixing 80 mm thick Precast cement concrete I-Shape interlocking paver block a with top layer of minimum 8mm thickness having plan dimension 200x(160+120mm) of O.P. cement, Smooth high gloss finish, skid reditant. manufactured from rubber moulds through vibro-compression machanism. The compressive strength of concrere paver block shall not be less than 30MPA (M-30) and wight 5kg per no confirming to IS; 15658-2006 with a 4 cm thick layer of fine sand including cost of material, labour, T & P TAXES etc requried for proper completion of the work as directed by Enginner-in-charge.S.O.R. SL. NO.5

CONSTRUCTION OF U TYPE DRAIN AS/ATTACHED ESTIMATE FOR 30X30CM

Granular Sub-base Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Excavation Work Excavation in foudation in ordinary soil(Loam,clay or Sand) including, Lift upto 1.50M, and lead upto 30m and including filling watering and ramming of excavated earth into the tranches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-in-charge upto a distance of 30M from the foundation tenches. (Where machine can not reach/Move). For building work Only. S.O.R 251

PCC Work Cement concrete with 4cm gauge approved stone, ballast approved coarse sand cement in the proportion of 1:4:8 including supply of all material , labour and T&P etc. required for proper completion of the work. S.O.R-281

Brick Work in Foundation First class brick work in 1:6 cement & coarse sand of 2.20 FM morter in foundation and plinth including supply of all matterial labour T&Petc.Required for proper completion of the work.

Internal Water Supply & Sanitary Installations & External Sewerage & Septic etc.

Internal Electric Installations.

Adjustment for Say