Bundelkhand Institute Of Engineering And Technology Tender

Density and specific gravity Specification : i. Density as per ASTM D1250, ASTM D792, ISO 1183 and DIN 51757 ii. Specific Gravity as per ASTM D1429 - 08 iii. Reference standards : ASTM, ISO, IS, DIN iv. System Status : Digital v. Data Entry : All Data through Console vi. Capacity : 220 grams. vii. Resolution : 1 mg. viii. Accuracy : ±0.001 ix. Media of testing : "Distill Water". x. Direct result display. xi. No Manual Calculation xii. Supply : 230 VAC/50 Hz.

Flow through Fluidized bed Specification : i. A column of daimeter 48 mm and height 750 mm should be made of borosillicate glass with both end made of stainless steel 304 Grade. ii. Fluidizing/Packing material i.e. Glass beads should be provided. iii. Water circulation by FHP Pump, Crompton/Standard make, from water tank, made of stainless steel 304 Grade, 1.5 mm thick, capacity 30 Ltrs. iv. Flow measurement should be done by Rotameter. v. Pressure drop measurement should be done by differential pressure manometer. vi. All the ball Valves should be Imported. Operating temperature range should be -40°F to 302°F, working pressure of valve should be in range of 600psi & valves should be able to use in vacuum pressure up to 2x10-5 psi. viii. The whole set-up should be well designed and arranged on a rigid structure painted with industrial PU Paint.

Carbon black content apparatus Specification : i. ASTM D 1603, IS 4984 and IS 2530 ii. Furnace size : 10 x 8 x 8 inch iii. Temperature Range : Ambient to 1000 °C. iv. Temperature control system: Microcontroller based PID controller. v. Resolution : 1 °C. vi. Accuracy : ±2 °C. vii. Accessories : Desiccator, Glass U tube, Combustion tube, Rota meter, Rubber tube {1 no. each}, Glass end Caps-2 nos. and Glass traps - 3 nos. viii. compact with safe assembly for glassware's. ix. Supply: 230 VACS/50 Hz x. Power : 1.5 KW xi. Paint : Powder coated.

Pressure drop in two phase flow Specification : i. Test Section of dia 1" Length 900 mm should be made of borosilicate glass. ii. Buffer Tank of Suitable Capacity with safety valve and pressure gauge should be made of stainless steel 304 Grade. iii. Water Circulation by FHP pump, Crompton/Standard make, from water tank, made by stainless steel 304 Grade/PVC, 1.2 mm thick, Capacity 60 Ltrs. iv. Air Circulation should be done by air Compressor. v. Water and air flow rate should be measured by Rotameter. vi. Separator of compatible capacity should be made by stainless steel 304 Grade. vii. Pressure drop measurement should be done by diffrential pressure manometer. viii. All the ball Valves should be Imported. Operating temperature range should be -40°F to 302°F, working pressure of valve should be in range of 600psi & valves should be able to use in vacuum pressure up to 2x10-5 psi. ix. The whole set-up should be well designed and arranged on a rigid structure painted with industrial PU Paint. x. Air compressor of 2HP is required , 8 CFM with automatic switch.

RTD Studies in Plug Flow tubular Reactor Straight Tube Type, Compressed Air Feed System. Specification : i. reactor of OD-32 mm. ID-25 mm, length-1200 mm should be made of Borosilicate glass. ii. Feed Circulation by compressed air feed system, from feed Tank, made of Stainless Steel 304 Grade, Thickness 2 mm . Capacity-20 Ltrs and flow measured by Rotameter. iii. Pressure Regulator 0-2kg/cm² and Pressure Gauge Bourdon type 0-2kg/ cm² should be provided. iv. Piping should be of Material Stainless Steel 304 Grade and PU pipe. v. Electronic Stop watch should be provided. vi. Arrangement should be provided to inject tracer into the inlet of reactor. vii. All the ball Valves should be Imported. Operating temperature range should be -40°F to 302°F, working pressure of valve should be in range of 600psi & valves should be able to use in vacuum pressure up to 2x10-5 psi. viii. The whole set-up should be well designed and arranged on a rigid structure painted with industrial PU paint. ix. Air Compressor (1 HP), 4 CFM with automatic switch.

Rotary drier Specification : i. Drying Shell of Length 1.5 m, Dia. 110 mm should be made of Stainless Steel 304 Grade. Thickness 2.5 mm. ii. Feed Hopper and Product Receiver of Compatible Capacity should be made of Stainless steel 304 Grade, Thickness 1.5 mm. iii. Variable Rotating Action by using motor coupled with a Reduction Gear Box. iv. Hot air circulation by forced draft fan and arrangement for variable air flow rate should be provided. v. Heating Chamber of Compatible capacity should be fitted with Nichrome wire heater controlled by PID controller, 0-199.9° C. A Tray attached with Digital weighing balance, 0-1000gm. of ±1 gm resolution. vi. Temperature measurement should be done by Temperature sensors of RTD PT-100 type with Digital Temperature Indicator (0-199.9°C.) vii. The whole set-up should be well designed and arranged on a rigid structure painted with industrial PU Paint.

RTD Studies in continuous Stirred Tank Reactor Compressed AIR Feed System Specification : i. Reactor of capacity 2 Ltrs. should be made of Stainless Steel 304 Grade, Thickness 2.5 mm and fitted with Stirrer having Stainless Steel Impeller and shaft coupled with FHP motor. ii. Feed Circulation by compressed air feed system, from feed Tank, made of Stainless Steel 304 Grade & Thickness 2mm, Capacity-20 Ltrs and flow measured by Rotameter. iii. Pressure Regulator 0-2 kg/cm² and pressure Gauge Bourdon type 0-2 kg/cm² hould be provided. iv. Piping should be of Material Stainless Steel 304 Grade and PU pipe. v. Electronic Stop watch should be provided. vi. Arrangement should be provided to inject tracer into the inlet of reactor. vii. All the ball Valves should be Imported. Operating temperature range should be -40°F to 302°F, working pressure of valve should be in range of 600psi & valves should be able to use in vacuum pressure up to 2x10-5 psi. viii. The whole set-up should be well designed and arranged on a rigid structure painted with industrial PU Paint. ix. Air Compressor (1 HP), 4 CFM with automatic switch

sieve plate distillation column Specification : i. Distillation column having diameter 110 mm with seven sieve plates and shell & tube condenser made of stainless steel 304 Grade not less than 2mm thick and reflux divider. ii. Steam generator should be made of stainless steel insulated with ceramic wool cladded with aluminum foil and fitted with Bourdon type pressure gauge, 0-2 kg/cm² , level indicator, safety valve, drain and Nichrome wire heater digitally controlled by PID controller 0-199.9° C. Hydraulically tested upto 8 kg/cm². iii. Distillate tank and bottom product tank should be made of stainless steel 304 Grade, Thickness 1.5mm capacity 5 liters(each). iv. Flow rate of cold water should be measured by Rotameter. v. Reflux Divided with special arrangement to change R/D ratio automatically. vi. Temperature sensors RTD PT-100 type to measure temperature. vii. Control panel should comprising of digital Temperature Controller: PID Controller, 0-199.9° C, digital Temperature Indicator: 0-199.9° C with multi-channel switch and Reflux timer for changing R/D ratio with Standard make On/Off switch, Mains Indicator etc. viii. the whole set-up should be well designed and arranged on a rigid structure painted with industrial PU paint.

Color Comparator Specification : i. Measuring Principle: Visual comparison with permanently colored glass standards ii. Mode : Transmittance iii. Light Source: Tungsten halogen lamp, 12 volt , 20 watt iv. Illuminant: C v. Path lenght : 33mm vi. Power pack: 12 Volt ac, switchable to suit 220/110 Volt supply vii.Approvals : CE viii. Instrument housing : ABS (Acrylonitrile Butadiene Styrene) fire resistance plastic ix. Dimensions: Width 231mm, depth 273 mm, height 142 mm x.Weight : 1.5 kg

Conductivity Meter Specification : i. Range -0 to 20 ,200 µS* . 0 to 2, 20 & 200 mS* ii. Readability -0.05% of range iii. Accuracy -±1% of Range iv.Repeatability -±1% of Range v. Readout -3½ digit 7 segment LED of . 12.7 mm height. vi. Size (WxDxH) in mm-295 x 165 x 140(1) vii.Weight (in kg) -Approx .3(2) viii.Power Requirement -230 V ±10% AC, 50 Hz ,1φ, 5 VA Max ix.Operating Frequency - 1000Hz x.Temp. Compensation - 0 to 50°C Manual xi.Temp. Co-efficient - 2% xii. Cell constant 0.1, 0.5 or 1.0 (Selecteable) xiii. Output - 20 mV Full Scale into 10 kΩ Resistive Impedance. xiiii. Accessories Supplied- With Instrument - Cell Stand with cell holding clip At -Extra cost -Dip type Conductivity cells of cell constants 0.1, 0.5 and 1.0

Chemical Engineering Laboratory

Thermo Gravimetric Analyzer Specification: i. Temperature range: room temperature to 1000°C or better ii. Heating Rate: 0.2 °C/min to 100 °C/min or better iii. Temperature accuracy: ± 1°C or better iv. Temperature precision: ± 0.5 °C or better v. Cooling time: ≤ 20 min (1000 °C to 50 °C) or better vi. Furnace type: low mass platinum/ceramic/quartz vii. Furnace movement: software controlled viii. Calibartion type: Auto calibration ix. Balance load capacity: ≥ 1 g x. Balance sensitivity: ≤ 1µg xi. Weighing Precision: ± 0.01% xii. Sample pan: Platinum, ceramic or alumina of ≥ 50 µL capacity xiii. other accessories: TGA must be equiped with integrated three purge gas cylinders and regulators of Nitrogen, Oxygen and Argon gas. xiv. Vacuum: 10 mbar or better xv. Real time data display xvi. Data analysis software: user friendly must run on Windows 10. It must show online graphs such as sample weight vs temperature et., It must have capability of data files (ASCII) import and export to word, excel, pdf format xvii. Destop computer (with i5 processor): with DVD writer, keypad, digital mouse with latest version of Windows and other necessary software and colour printer must be provided xviii. Calibration Kit, Sample handling accessories must be provided xix. Gas flow controllers and connections: digital mouse flow controller with automatic gas switching, control/setting of flow rate by software xx. UPS: branded 5KVA Capacity with 3 years warranty xxi. Table/Plateform: branded table for placing/ installation the equipment and other accessories xxii. Power supply: 100 -240 VAC/ 50-60 Hz xxiii. Warranty on equipment: 3 years or more xxiv. Training and support must be provided at free of cost by the supplier xxv. Installation of the equipment with all the required accessories must be provided by the supplier and the cost must be included in the offer price xxvi. User's manual and maintenance manual must be provided

Ball Mill Specification : i. Ball Mill should be fitted on a sturdy MS frame having Dia. 275 mm, Length 350 mm & Thickness 4 mm, and drive by 1 HP motor with variable speed arrangment coupled to reduction gearbox till critical speed. ii. Feed size: 6mm (approx) and product size: 200 mesh (approx). iii. Product receiver should be of stainless steel 304 grade. iv. Discharge chute should be of suitable size. v. The set-up should be able to reduce the product size up to 200 mesh. vi. Control panel should comprises of non-contact type digital RPM indicator with proximity sensor for RPM measurement and electronic energy meter for power measurement. vii. The set-up should be fitted with required guard. viii. The whole set-up is well designed and arranged on rigid structure painted with industrial PU paint. Balls: i. Steel Balls, 40 mm dia approx.,18 nos. ii. Steel Balls, 36 mm dia approx., 25 nos. iii. Steel Balls, 30 mm dia approx.,42 nos. iv. Steel Balls, 25 mm dia approx.,75 nos. v. Steel Balls, 20 mm dia approx.,150 nos. vi. Steel Balls, 19 mm dia approx.,170 nos. vii. Steel Balls, 12.5 mm dia approx.,600 nos.