Bareilly Development Authority Tender

Providing and injecting chemical emulsion for preconstructional entitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at ground floor only shall be measured as per I.S 6313 ( Part II 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chloro Pary Phas will be used. The rate of application of chemical emulsion shall be as follows: (1) Treatment for masonary & foundation 5 liters per / 100 sqm. (2) Back fill in immediate contact with foundation 7.5 liters/100sqm. (3) Treatment of top surface of plinth filling 5 liters/ 100sqm. (4) Treatment junction of wall and the floor 7.5 liters/100sqm. (5) Treatment of soil along external perimeter of building 7.5 leters/100sqm. (6) Treatment of soil under apron along external perimter 5 liters /100 sqm. P.W.D. SOR CH- 8 New Item 1

Providing & laying cement concrete 1 : 4 : 8 ( 1 cement : 4 Coarse sand : 8 graded stone ballast 40mm nominal size) in foundation and plinth/under floors and curing complete, including cost of form work in foundations & floors. P.W.D. SOR Item No. 281

P.C.C.(1 : 2 : 4) in fixing of Hold fast on Door , Window & Ventialtor P.W.D. SOR Item No.279

R.C.C. work with cement approved coarse sand and 2 cm. (3/4") guage approved stone ballast in the proportion 1:2 : 4 (1 cement : 2 C. sand : 4 stone aggregate) in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 B WG binding wire and including necessary centering and shuttering etc. and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works strength of the concrete shall not beless than M-20. but in R.C.C Column Footing 1 : 1.5 : 3 having strength not less than M - 20 P.W.D. SOR Item No. 287+diff

As in item 7 above but in R.C.C Plinth Band 1 : 1.5 : 3 having strength not less than M - 20 P.W.D. SOR Item No. 285

As in item 7 above but in R.C.C Column 1 : 1.5 : 3 having strength not less than M - 20 P.W.D. SOR Item No. 289

As in item 7 above but in R.C.C Lintal Band 1 : 1.5 : 3 having strength not less than M - 20 P.W.D. SOR Item No. 283A

As in item 7 above but in R.C.C Beam 1 : 1.5 : 3 having strength not less than M - 20 P.W.D. SOR Item No. 286

As in item 7 above but in R.C.C. Slab in 1:1.5:3 having strength not less than M- 20. P.W.D. SOR Item No. 284A

Mild Steel or iron in plain work such as reinforced concrete or reincorced, brick work (when not included in anover all rates) wrought to requrired shape as necessary including bending for proper completion of the work and includng supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. P.W.D. SOR Item No. 504

25m thick damp proof coarse with cement concreat consistion of 1 part cement 1.5 approved coarse sand 3 part graded stone great and including water proofing material as dirated by Engr.-in- charge in the proportion as spacified by the manufacture. P.W.D. SOR Item No. 361a

Bitumen painting on D.P.C. with two coats of air blown bitumen 85/50 or 85/25 @ about 1.70 kg/ Sqm. Inclucing cost of fule if any. P.W.D. SOR New Item 1, Ch-7

Class 150 Brick work in 1:4 cement and Coarse Sand of 1.25 finentss modulusbut in Foundation plinth level including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cms. P.W.D. SOR Item No. 305

Class 150 Brick work in 1:4 cement and Coarse Sand of 1.25 finentss modulusbut in Super-structure above plinth level upto floor two level including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cms. P.W.D. SOR Item No. 305+309+310

Press steel Door chaukhats supply of M.S. steel 18 guage (1.25mm) pressed steel door Chaukhats including S/F of iron but hinges of 100 x3 mm I.S.I. mark with drilling holes for L-droop and pipes 15 x 12 mm C leats for tower bolt and 40 x6 mm hold fast 230 mm long including supply of all meterials Labour T & P carriage upto site required proper complection of work as per direction of E/I P.W.D. SOR Item No.10.14.1

Supply & fixing of Flush Doors commercial quality conforming to I.S. 2202 Part I (1983) including fixing of wooken cleats and stoppers and including fixing and adjustment of hinges, bolts, locks, handle, springs and other fittings but excluding their supply and including painting with two coats of Black Japan paint on all iron fitting if necessary 32mm thick. P.W.D. SOR Item No. 470i

Supply & fixing mann or Mahaveer or other approved (ISI- marked) Z- section double leaf openable shutters steel window with required shish bars including supply and fixing of approved heavy quality M.S. hinges , handles 30 cm long stays, and hold fast etc, complete wrought to required form including drilling holes , rivetting welding where necessary & also including supply of steel fitting bolts , nuts , wastage and labour etc. and their fixing required for proper completon of the work. P.W.D. SOR Item No. 502b

Providing & Fixing of Glass Pannes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). D.S.R. Item No. 9.7.7.2

S/F of M.S. Hold fast P.W.D. SOR Item No 502a

P/L 12 mm thick plaster 1 : 4 (1cement : 4 fine sand 1.25 F.M.) Mortar in Fair face of wall P.W.D. SOR Item No 584+587

P/L 15 mm thick plaster 1 : 4 (1cement : 4 fine sand 1.25 F.M.) Mortar in Rough face of wall P.W.D. SOR Item No 584+596

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. D.S.R. Item No. 11.41.1

S/F 5 mm thick china white glazed tiles in skirting or dado laid with 1 : 3 cement & approved coarse sand mortar finished with white cement slurry tointing and polishing materials labour and tools & plants etc. required for proer compeltion of the work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. D.S.R. Item No. 13.80

Finishing walls with Acrylic Smooth Exterior Paint required shade on undecorated wall surfaces (two coat) overone and including one coat white cement primer to give an even shade after thoroughly brushing the surface to powdered materials including curing and cost of all materials. P.W.D. SOR Item No. 13.46.1

Making & Fixing M.S. Iron main Door P.W.D. SOR Item No. 502b

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) D.S.R. Item No. 5.14

Extra for shuttering in circular work (20% of respective centering and shuttering items) 20% for Cornices and mouldings in circular columns D.S.R. Item No.5.9.14

Painting Two coat over priming coat (but including cost of priming coat) on steel and other matal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10 sqm in area white superior synthetic enamel of BURGER , NEROLEC brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. P.W.D. SOR Item No. 1b+2+3(ii)

Providing and laying pressed clay tiles (as per approved pattern 20mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete. D.S.R. Item No. 12.20

Supply and fixing of hexagonal fan box with hexagonal side of approximate 80mm in length fabrication from 16 SWG M.S sheet in corporate 10mm sheet in corporate 10mm and M.S round bar dully bent for supporting fan hanger etc all complete. SI No 1149/elctrical SOR 2018

Providing and fixing almunium sliding door bolts ISI mark Anodised(Anodic coating not less than great ac10 as per IS:1868 transparent are dyed to required colour are shade with nuts and screws etc complete 300 x 16 mm long D.S.R. Item No. 9.96.1

Providing and fixing almunium sliding door bolts ISI mark Anodised(Anodic coating not less than great ac10 as per IS:1868 transparent are dyed to required colour are shade with nuts and screws etc complete 250 x 16 mm long D.S.R. Item No. 9.96.2

Providing and fixing almunium tower bolts ISI mark Anodised(Anodic coating not less than great ac10 as per IS:1868 transparent are dyed to required colour are shade with nuts and screws etc complete 300 x 10 mm long D.S.R. Item No. 9.97.1

Providing and fixing almunium tower bolts ISI mark Anodised(Anodic coating not less than great ac10 as per IS:1868 transparent are dyed to required colour are shade with nuts and screws etc complete 250 x 10 mm long D.S.R. Item No. 9.97.2

Providing and fixing almunium handle ISI mark Anodised(Anodic coating not less than great ac10 as per IS:1868 transparent are dyed to required colour are shade with nuts and screws etc complete125 mm long D.S.R. Item No. 9.100.1

Providing and fixing almunium handle ISI mark Anodised(Anodic coating not less than great ac10 as per IS:1868 transparent are dyed to required colour are shade with nuts and screws etc complete100 mm long D.S.R. Item No. 9.100.2

Supply and fixing and concealing of 20 mm dia. 2mm thick PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc required for proper completion of the work as per directions and to the satisfaction of Engineer in charge. SI No 148(A)/elctrical SOR 2018

Supply and fixing of 2/3/4 ways round Steel junction box confirming to ISS for 20mm dia 16 gauge conduit concealed in wall, keeping its level upto plaster duly provided with proper size cover, screwed as directed at site by the Engineer I/C with supply of all material labour and T&P required for proper completion of work. SI No 154/elctrical SOR 2018