Banaras Hindu University Tender
If you're a registered bidder for etender UP and want to inquire about any e-tender UP government has posted, this is your stop. No need to enter every detail on the website of <a href="https://etender.up.nic.in">etender.up.nic.in</a> - BidAssist filters will help you find the exact UP etender you're looking for. Read to learn how to search & bid for etender UP.
Banaras Hindu University - BHU Tender
Electrical and Electronics
Electrical Works
Eprocure
Opening Date24 Jun 2024
Closing Date1 Jul 2024
Tender Amount₹ 1,72,43,462
Costs
EMD
₹ 3,44,869Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_BHU_813204_1Bid Award Id
ViewTender No
UWD/2024/24062024-1Tender Authority
Banaras Hindu University ViewPurchaser Address
-Website
http://http://www.bhu.ac.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Construction of Central Hindu School on First Floor (Phase-II) including electrical installation work at RGSC, Barkachha, BHU
BOQ Items
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) (4.1.8)
4
24624
6156.08
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. (4.17)
146
95326
652.92
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
Cement mortar 1:6 (1 cement : 6 coarse sand) (6.1.2)
9
58924
6547.22
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
In cement mortar (15.7.4)
25
39073
1562.94
Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
G.S. Sheet (15.28.1)
42
5444
129.62
Demolishing thatch roofing including mats, bamboo, jaffari etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. (15.32)
921
40441
43.91
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (15.60)
49
7234
147.64
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
Cement mortar 1:6 (1 cement : 6 coarse sand) (6.4.2)
381
3075024
8070.93
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) (6.13.2)
70
69377
991.1
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). (5.3)
246
2553935
10381.85
Centering and shuttering including strutting, propping etc. and removal of form for :
Lintels, beams, plinth beams, girders, bressumers and
cantilevers (5.9.5)
303
177857
586.99
Centering and shuttering including strutting, propping etc. and removal of form for :
Suspended floors, roofs, landings, balconies and access
platform (5.9.3)
944
695652
736.92
Centering and shuttering including strutting, propping etc. and removal of form for :
Edges of slabs and breaks in floors and walls
Under 20 cm wide (5.9.16.1)
46
8474
184.22
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more. (5.22A.6)
21250
1886787
88.79
Finishing walls with Acrylic Smooth exterior paint of required shade :
New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) (13.46.1)
984
172327
175.13
Finishing walls with Acrylic Smooth exterior paint of required shade :
Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm)
on existing cement paint surface (13.111.1)
920
97722
106.22
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :
New work (two or more coats) over and including water thinnable priming coat with cement primer (13.41.1)
2480
404636
163.16
Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats) (13.90.1)
2480
143195
57.74
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (13.80)
3400
416296
122.44
12 mm cement plaster of mix :
1:6 (1 cement: 6 coarse sand) (13.4.2)
2919
817991
280.23
6 mm cement plaster of mix :
1:3 (1 cement : 3 fine sand) (13.16.1)
870
210313
241.74
Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.
Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (10.15.1)
3930
573740
145.99
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.
Fixed to steel windows by welding (9.48.1)
505
88758
175.76
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.
M.S. tube (10.26.1)
310
48009
154.87
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (9.21.1 )
43
86263
2006.13
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (9.21.2)
13
25154
1934.99
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). (9.23)
56
23901
426.81
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :
300x16 mm (9.96.1)
26
7109
273.43
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
200x10 mm (9.97.3)
44
4210
95.7
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
125 mm (9.100.1)
78
4947
63.43
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
Twin rubber stopper (9.101.2)
30
1979
65.98
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
Two or more coats on new work (13.61.1)
280
36187
129.24
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) (4.1.3)
29
209331
7218.32
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :
One or more coats on old work (13.99.1)
280
23802
85.01
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :
4.0 mm thick glass panes (10.30.1)
44
42132
957.55
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
25 mm thick (11.26.1)
1100
1791702
1628.82
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.(11.27)
77
148196
1924.63
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (8.31)
73
79972
1095.52
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. (11.38)
35
37092
1059.79
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Granite of any colour and shade
Area of slab over 0.50 sqm (8.2.2.2)
36
153407
4261.33
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.
Granite Stone of approved shade (8.10.2)
1.5
5130
3420.53
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:
White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (17.1.1)
4
23058
5764.68
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :
W.C. pan with ISI marked white solid plastic seat and lid (17.2.1)
2
11187
5593.97
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap (17.7.2)
5
14627
2925.46
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :
Single half stall urinal with 5 litre P.V.C. automatic flushing cistern (17.5.1)
4
39812
9953.13
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
Semi rigid pipe
40 mm dia ( 17.28.1.2)
5
523
104.63
Providing and fixing 100 mm sand cast Iron grating for gully trap. (17.29)
5
237
47.42
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (17.31)
5
6821
1364.27
Providing and fixing soil, waste and vent pipes :
100 mm dia
Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 (17.35.1.2)
33
38324
1161.34
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc.:
For 100 mm dia pipe (17.37.1)
10
3056
305.65
Providing and fixing plain bend of required degree.
100 mm dia
Sand cast iron S&S as per IS : 3989 (17.39.1.2 )
10
4154
415.48
Providing and fixing single equal plain junction of required degree:
100x100x100 mm
Sand cast iron S&S as per IS - 3989 (17.44.1.2)
5
3549
709.97
Providing and fixing collar :
100 mm
Sand cast iron S&S as per IS - 3989 (17.57.1.2 )
7
3047
435.37
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :
100 mm (17.58.1)
15
7678
511.93
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
100 mm inlet and 100 mm outlet
Sand cast iron S&S as per IS: 3989 (17.60.1.1)
8
12866
1608.29
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
25 mm dia nominal bore (18.10.3)
50
23286
465.73
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
15 mm dia nominal bore (18.10.1)
60
18175
302.93
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
25 to 40 mm nominal bore (18.13.1)
1
716
716.08
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
25 mm nominal bore (18.17.1)
2
1057
528.62
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
25 mm nominal bore (18.18.3)
2
837
418.94
Providing and fixing uplasticised PVC connection pipe with brass unions :
45 cm length
15 mm nominal bore (18.21.2.1)
10
882
88.25
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (18.33.1)
2
19752
9876.36
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :
15 mm nominal bore (18.46.1)
4
1002
250.67
6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. (13.17)
35
11225
320.74
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
15 mm nominal bore (18.51.1)
5
2936
587.31
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
15mm nominal bore (18.53.1)
5
2828
565.68
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
15 mm nominal bore (18.52.1)
14
9024
644.63
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,
(i) Single socketed pipes.
110 mm diameter (12.41.2)
75
24327
324.36
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
Bend 87.5°
110 mm bend (12.42.5.2 )
10
1380
138.07
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
Shoe (Plain)
110 mm Shoe (12.42.6.2 )
10
1210
121
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm, hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
110 mm (12.43.2)
80
24566
307.08
Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (10.1)
250
22875
91.5
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (12.50)
45
30027
667.27
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:
(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by ngineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.
(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.
(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge.
(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.
(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (22.7.1)
863
1283306
1487.03
Electrical Work
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Make- for switch-legrand/ Anchor/L&T/Havells) (Make for -Wire -Polycab/Havells/Finolex/ RR Kabel).
Group C (1.10.3)
215
226324
1052.67
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Make for -Wire -Polycab/ Havells/Finolex/RR Kabel).
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (1.14.1)
180
27943
155.24
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Make for -Wire -Polycab/ Havells/Finolex/RR Kabel).
2 X 4 sq. mm + 1 X 4 sq. mm earth wire (1.14.3)
280
59544
212.66
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Make for -Wire -Polycab/ Havells/Finolex/RR Kabel).
2 X 6 sq. mm + 1 X 6 sq. mm earth wire (1.14.4)
40
10590
264.76
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Make for -Wire -Polycab/ Havells/Finolex/RR Kabel).
4 X 6 sq. mm + 2 X 6 sq. mm earth wire (1.14.9)
120
50272
418.94
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Make for -Wire -Polycab/ Havells/Finolex/RR Kabel).
4 X 10 sq. mm + 2 X 6 sq. mm earth wire (1.14.10)
150
86605
577.37
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (Make for -Wire -Polycab/ Havells/Finolex/RR Kabel).
4 X 16 sq. mm + 2 X 6 sq. mm earth wire (1.14.11)
30
23988
799.6
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required (Make- AKG/Surya/Polycab/KT)
25 mm (1.21.2)
450
43065
95.7
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. (Make- D-Link/ C2G/ frontech/Polycab/Legrand).
1 run of cable (1.53.1)
450
23445
52.1
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Make-legrand/Anchor/ L&T/Havells).
5/6 amps switch (1.24.1)
30
2711
90.38
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Make-legrand/Anchor/ L&T/Havells).
15/16 A switch (1.24.3)
15
2105
140.36
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Make-legrand/Anchor/ L&T/Havells).
3 pin 5/6 A socket outlet (1.24.4)
30
3540
118.03
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(Make-legrand/Anchor/ L&T/Havells).
6 pin 15/16 A socket outlet (1.24.5)
15
2791
186.08
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (Make-legrand/Anchor/L&T/Havells) (1.25)
51
18546
363.65
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required (Make-Legrand/Achor/L&T/ havells ) (1.26)
10
340
34.03
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. (Make-legrand/ Anchor/L&T/Havells).
1 or 2 Module (75mmX75mm) (1.27.1)
30
7751
258.38
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. (Make-legrand/ Anchor/L&T/Havells).
12 Module (200mmX150mm (1.27.6)
15
4258
283.9
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1 nos - 6 pin 5/6 & 15/16 A modular socket outlet and 1 Nos-15/16 A modular switch, connections etc. as required.(Make- legrand/Anchor/L&T/Havells) (1.32)
12
6315
526.33
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.(Make-Ridder/Anchor/ Kinjal/Havells). (1.33)
10
691
69.11
Supplying and fixing PVC batten/ angle holder including connections etc. as required (Make-Phillips/Anchor/Havells /Kinjal) (1.58)
2
191
95.7
Providing and fixing plain 16/0.20mm (0.50sqmm) twin circular flexible FRLS PVC insulated, PVC sheathed copper conductor cable direct on the wall with PVC clips etc. as required (1.40)
5
111
22.33
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings (Make-legrand/Anchor/L&T/ Havells) (1.56)
11
6807
618.84
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required (Make-legrand/Anchor/L&T/Havells) (1.57)
2
1358
679.45
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required. (Make-legrand/ABB/Schineder/ Siemen/ L&T/ Havells).
4 way (4 + 12), Double door (2.5.1)
1
6008
6008.71
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
125 A, 36 KA,FPMCCB (2.2.14)
1
7979
7979
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) .(Make-legrand/ABB/Schineder/ Siemens/ L&T/Havells)
4 way (4 + 12), Double door (2.4.1)
2
6524
3262.2
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
8 way , Double door (2.3.2)
4
7485
1871.41
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required .(Make-legrand/ABB/Schineder/Siemen/L&T/Havells).
Single pole (2.10.1)
52
11003
211.6
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required .(Make-legrand/ABB/Schineder/Siemen/L&T/Havells).
Double pole (2.10.3)
4
2364
591.19
Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. (Make-legrand/ABB/Schineder/ Siemen/L&T/Havells)
For 4 way, Double door TPN MCBDB (2.24.1)
2
1922
961.22
Supplying and fixing Cable End Box (Loose Wire Box) suitable fortriple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required. (Make-legrand/ABB/Schineder/ Siemen/L&T/Havells). (2.25)
1
812
812.36
Supplying and fixing cable end box (Loose wire box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240Volts, on surface/ recess, complete with testing and commissioning etc. as required.
For 8 way, Double door SPN MCBDB. (2.23.2)
4
3109
777.27
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. (Make-Rex/duraline/Gemini).
90 mm dia (OD-90 mm & ID-76 mm nominal) (14.16.2)
86
22769
264.76
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ X 70 sq. mm (38 mm) (9.1.23)
1
391
391.29
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.(Make-B class-Jindal/TATA/QST). (5.2)
2
11288
5644
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm). (5.9)
16
2228
139.29
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable trench etc as required. (5.18)
20
786
39.34
Supplying and fixing of light class G.I. pipe of 50 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required. (Make-Jindal/TATA/QST). (12.37)
2
3502
1751.26
Supplying and fixing of 32mm dia x 2.0 Metres long G.I. pipe (medium class) bracket for mounting LED fittings/HPMV/ HPSV street light fitting on pole including bending the pipe to the required shape, 2 Nos. 40mm x 3mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.(12.34)
11
11836
1076
Supplying and fixing 63 A, 10 KA rating, triple pole, 415 V, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make-legrand/ABB/Schineder/Siemen/L&T/Havells). (MR)
2
3864
1932
Supplying, Installation, Testing and commissioning of surface/wall/Pendent mounted 20 watt LED batten light of 4 feet long with minimum lumen output 2000 lumen made of extruded Aluminium housing and shall have polycarbonate diffuser including connection with 1.5 Sq mm FRLS PVC insulated copper conductor single core cable with earthing and suitable for 230 volt 50Hz ,single phase AC supply complete etc as required. (Make-Crompton Model No CCS-100-20-65 HL2-DP-NWHor equivalent specification of Wipro/Havells/Bajaj/ Phillips).(MR)
123
74907
609
Supplying, Installation, Testing and commissioning of wall mounted mirror light of 10 watt LED batten light of 2 feet long with minimum lumen output 1000 lumen made of extruded Aluminium housing and shall have polycarbonate diffuser including connection with 1.5 Sq mm FRLS PVC insulated copper conductor single core cable with earthing and suitable for 230 volt 50Hz ,single phase AC supply complete etc as required. (Make-Crompton Model No CCS-100-20-65 HL2-DP-NWHor equivalent specification of Wipro/Havells/Bajaj/Phillips) (MR)
2
924
462
Supplying, Installation, Testing and commissioning of Surface mounted round LED downlight with AL die-cast body, finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation LED down light 18 watt to 20 watt LED with minimum lumen output 1800 lumen including making hanging arrangement using metallic chain wherever required or fixing with fastener on ceiling and connection with 1.5 Sq mm FRLS PVC insulated copper conductor single core cable with earthing and suitable for 230 volt 50Hz ,single phase AC supply complete etc as required. . (Make:-Make- Bajaj Model No BGSLOSLEEK SURFACE 18 W WHRD or equivalent specification of Crompton/Havells/ Wipro/ Phillips). (MR)
25
44750
1790
Supplying, Insttalation, testing and commissioning of 1200 mm sweep Electrical ceiling fan with 3 nos blades , 30 cm long down rod, 2 nos canopies, shacket kit ,copper winding and service value minimun 4 ,air delivery 210 CMM ,350 RPM (tolrance as per IS:374-2019) suitable for 230 volt 50Hz ,single phase AC supply with earthing connection including connection with FRLS 3 core wire etc complete as required at site. (Make-Havells Model No FHCSV1SWHT48 or equivalent specification in Crompton/Usha/Bajaj). (MR)
44
120032
2728
Supplying, Insttalation, testing and commissioning of 1400 mm sweep Electrical ceiling fan with 3 nos. blades , 30 cm long down rod, 2 nos canopies,shacket kit ,copper winding and service value minimun 4 ,air delivery 210 CMM ,350 RPM (tolrance as per IS:374-2019) suitable for 230 volt 50Hz ,single phase AC supply with earthing connection including connection with FRLS 3 core wire etc complete as required at site. (Make-Havells Model No FHCSV1SWHT48 or equivalent specification in Crompton/Usha/Bajaj). (MR)
7
20958
2994
Supplying, Insttalation, testing and commissioning of 300 mm impelled dia 900 RPM heavy duty industrial exhaust fan metallic body & motor suitable for 230 volt, 50 Hz., single phase AC supply with earthing connection on existing opening including connection with FRLS 3 core wire etc. complete with louvers/shutters as etc. required at site. (Make :- Crompton/ Havells/Usha/Haitan/Orient). (MR)
3
11010
3670
Supplying and fixing 63 A , 10 KA rating, Four pole, 415 V, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make-Legrand/ABB/Schineder/Siemen/L&T/Havells).(MR)
2
4830
2415
Supplying, installation, testing and commissioning of 45 to 50 watt LED street light luminaire designed for weather proof condition with excellent thermal management made of pressure die casting housing with toughened glass and high power LED with secondary optics and IP 66 protection with minimum lumen output 4500 lumen including fixing of G.I. wall bracket of 40-50 mm dia upto 1.00 meter long with 2 Nos. C clamp with suitable size fastener, connection with 1.5 Sqmm. FRLS PVC insulated copper ocnductor single core cable with earthing and suitable for 230Volt 50Hz. single phase AC supply complete etc. as required. (Make :- Crompton/Wipro/ Havells/ Phillips). (MR)
11
50193
4563
Supplying and fixing of internet socket outlet (RJ-45) on modular plate including connection etc complete as required at site (Make :- D-Link/ Cisco/Ubiquiti/Fedus/Roacool/Legrand). (MR)
30
23040
768
Supplying and laying of one number PVC insulated and PVC shaethed/ XLPE power cable of 1.1 KV grade of following size UG cable size direct in the existing RCC/HUME/Metal pipe/DWC pipe as required and refilling the trench etc as required.(Make-Polycab/Universal/Grandlay/ Gloster)
3½ X 70 sq. mm (MR)
86
72154
839
Supplying and laying of one number PVC insulated and PVC shaethed/ XLPE power cable of 1.1 KV grade of 3.5x35 Sqmm. UG cable size direct on wall surface etc. (clamped with 1mm thick saddle) as required. (Make-Polycab/ Universal/Grandlay/ Gloster)
3½ X 70 sq. mm (MR)
6
5400
900
Supplying and laying of one number PVC insulated and PVC shaethed/ XLPE power cable of 1.1 KV grade of following size in loose for connection etc. as required. (Make-Polycab/ Universal/Grandlay/ Gloster)
3½ X 70 sq. mm (MR)
4
3156
789
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements