Agra Development Authority Tender

Racking out joints of brick work in cement or lime mortar to depth of 1cm (3/8") including disposal of refuse as directed by the distance of 60 meters (200 feet) (CH-17 S.I. No. 707 SOR 2020-21)

RCC work Providing and laying in position specified grade of reinforced cement concrete, slab including the cost of centering, shuttering, finishing and excluding reinforcement - Above plinth level upto fifth floor lable: 1:1.5:3 (1 cement :1.5 coarse sand : 3 graded stone) (CH-5 S.I. No. 5.1.2 SOR 2020-21)

Reinforcement of Reinforced concrete or reinforced brick work (When not included in and an over all rates) brought to required shape as necessary including bending for proper completion of the work and including the supply of steel and its waistage Bend, hooks, Binding wire and authorized over lapping shall be measured upto floor two level. (S.I. No. 504 SOR 2020-21)

Mild steel and iron work of small size and section such as holding down Bolts, hold fasts, tierods, grating, etc. (When not included in and over all rates) brought to required form including supply of steel and its wastage including cost of bolts, nuts if required for proper completion of work including fabrication of holes in door chaukhats and nosing. (CH-10 S.I. No. 502 SOR 2020-21) Fabrication of grill/stairs case railing

Providing and laying integral cement based water proofing treatment BIRCK KOBA including preparation of surface as required for treatment of roofs, consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS. 2645 including adjoining walls upto 300 mm height. (b) Laying brick bats with mortar with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 to required slope including rounding of junctions of walls and slabs (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final be flooded with water for a minimum period of two weeks for curing and for final test. With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (CH-11 S.I. No. 2 SOR 2020-21)

15mm thick Cement plaster with cement mortar in proportion of 1:4 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm. In girth and finished even and smooth. (CH-13 S.I. No. 13.5.1 SOR 2020-21) 1 cement : 4 Coarse sand

12mm Thick cement plaster in single coat on fair side of single or half brick wall for interior plastering upto floor two level including internal rounded angles not exceeding 80mm in girth, chamfers and finished even and smooth. (CH-13 S.I. No. 13.4.1. SOR-2020-21) 1 cement : 4 Coarse sand

Finishing walls with Putty approved brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work. (CH-15 Item No. 27 SOR 2020-21)

Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.25 Ltr/10sqm including one coat of primer applid @ 0.75Ltr/10sqm coat curing and cost of all material, labour, T&P etc. required for proper completion of work.for two coat. (CH-15 Item No. 31 SOR 2020-21)

Finishing walls with acrylic emulsion paint of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work.for two coat. (CH-15 Item No. 30 SOR 2019-20)

Providing and laying cement concrete in 4:2:1 of not less than strength of M-150 stone ballast (20 mm nominal size), approved coarse sand and cement, curing complete including of cost of form work in foundation and floors-completion of the work as per direction of the E / I. (CH-5 S.I. No. 4.1.3 SOR-2020-21)

Class-150 brick work in 1:4 Cement and Coarse sand of 2.25 fineness modulous mortar in super structure above plinth level upto floor five level including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cm. (CH-6 S.I. No. 6.1.1 + 6.8A SOR-2020-21)

Kota stone slab flooring over 20mm thick (average) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 Coarse sand) 25mm thick. (CH-14 S.I. No. 10 New Item SOR 2020-21)

Kota stone slab 20mm thick in risers of steps, skirting dado and pillars laid on 10mm thick cement mortar 1:3 (1 cement : 3 coarse sand) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (CH-14 Item No. 11 SOR-2020-21

Providing and fixing of 35mm thick ISI marked flush door shutters conforming to IS : 2202 (Part-I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked stainless steel butt hinges with necessary screws, steel handels, Siliding bolt, Door Stopper and tower bolt. (CH-9 S.I. No. 9.21.1 SOR 2020-21)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per (Cost of aluminium snap beading shall be paid in basic item): (CH-9 Item No. 7 SOR 2020-21) i) With float glass panes of 4.0 mm thickness

Providing and laying Ceramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacture) of 1st quality conforming to IS : 15622 of apporved make in colours such as White, lvory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 Coarse sand), Jointing with grey cement slurry@3.3kg/sqm including pointing the joints with white cement and matching pigment etc, complete. (CH-14 Item No. 7 SOR 2020-21)

Supply and hoisting of 500 Litre Sintex or equivalent high density polyethylene seamless of piece moulded tanks and placing the same in proper position including all taxes, labour and T&P etc. for proper completion of work. Tank should be ISI marked, Sintex or equivalent. (CH-19 S.I. No. 2 SOR 2020-21)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid (CH-24 Item No. 2 SOR 2020-21)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: (CH-24 Item No. 3 SOR 2020-21) White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: (CH-24 S.I. No. 5 SOR 2020-21) Kitchen sink with drain board i) 510x1040 mm bowl depth 250 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (CH-24 S.I. No. 7 SOR 2019-20)

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. (CH-24 S.I. No. 8 SOR 2020-21) Flexible pipe (40mm dia)

Providing and fixing of 25 mm nominal outer dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (CH-23 S.I. No. 7 SOR 2020-21)

Providing and fixing of 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931. (CH-23 S.I. No. 22 SOR 2020-21)

Providing and fixing of 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (CH-23 S.I. No. 23 SOR 2020-21)

Providing and fixing of 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved quality conforming to IS:8931 (CH-23 Item No. 27 SOR 2020-21)

Providing and fixing of 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (CH-23 Item No. 27 SOR 2020-21)

Black granite Polished stone flooring with 18mm thick marble stone, as per sample of marble apporved by Engineer-in-charge, over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Black Granite Stone quality. (CH-14 Item No. 8 SOR 2020-21)

Electric work Supply and fixing and concealing of 25 mm dia. 2mm thick PVC conduit pipe with ISI mark embossed and with PVC accessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid, plastering with cement sand mortar finished to the level with matching colour wash including cost of all material labour and T&P etc required for proper completion of the work as per directions and to the satisfaction of Engineer in charge. (S.I. No. 149(A) / 2018)

Supply and fixing of BEE 5 star rated-1200 mm. sweep ceiling fans with fan motor. (S.I. No. 1501 (i) / 2018)

Supply and fixing of 22 LED metal body batten fitting complete lumens suitable mounting for on both surface & suspended with 5 years warrantee. complete in all respect. CAT-A 1980 system lumens, 90lm/watt PF0.95 THD10%, CRI80, with 2 year warrantee. (S.I. No. 1413(A) / 2018)

Supply and fixing of 20 watt LED bulb.

Supply and fixing of fresh air fan. (S.I. No. 1501 (i) / 2018)

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. (Code No. 1.23 DSR-2018) Supply and fixing of 5 Amp. Socket. etc. as required. (Code No. 1.23.1 DSR-2018)

Supply and fixing of 15 Amp. Socket. etc. as required. (Code No. 1.23.5 DSR-2018)

Supply and fixing of 5 Amp. Switch. etc. as required. (Code No. 1.23.1 DSR-2018)

Supply and fixing of 5 Amp. Two way Switch. etc. as required. (Code No. 1.23.2 DSR-2018)

Supply and fixing of 15 Amp. Switch. etc. as required. (Code No. 1.23.3 DSR-2018)

Supply and fixing of copper cable 1 core 4mm sqm. (Code No. 1103 DSR-2018)

Supply and fixing of copper cable 1 core 2.5mm sqm. (Code No. 1102 DSR-2018)

Supply and fixing of copper cable 1 core 1.5mm sqm. (Code No. 1101 DSR-2018)

Supply and fixing of copper cable 1 core 1.0mm sqm. (Code No. 1101 DSR-2018)

Supply and fixing of G.I. Box. Modular GI box for 2 module (Code No. 1300 DSR-2018)

Modular GI box for 3 module (Code No. 1301 DSR-2018)

Modular GI box for 4 module (Code No. 1302 DSR-2018)