Agra Development Authority Tender

Class-150 (Non Modular) brick work in 1:4 Cement and Coarse sand mortar in foundation and plinth including supply of all materials, labour and T & P etc. required for proper completion of the work. (CH-6 DSR S.I. No. 6.1 SOR-2020-21)

Reinforced cement concrete work in walls (any thickness), including attachedpilasters, buttresses, plinth and string courses, fillets, columns, pillars, plers, abutments, posts and struts etc, including cost of centering, shuttering, finishing and excluding reinforced :- 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). (CH-5 S.I. No. 5.2.2 SOR 2020-21) 5.1 upto plinth level

Above plinth level upto fifth floor lable.

RCC work Providing and laying in position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and excluding reinforcement - All work upto plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). (CH-5 S.I. No. 5.1.2 SOR 2020-21)

Reinforced cement concrete work in beams, suspended floors, roofs having balconies, shelves, chajjas, band, staircesss and spiral stair cases above plinth level upto floor five level, including the cost of centering, shuttering, finishing and reinforced, with :1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone). (CH-5 S.I. No. 5.3 SOR 2020-21)

RCC work Providing and laying in position specified grade of reinforced cement concrete, slab including the cost of centering, shuttering, finishing and excluding reinforcement - Above plinth level upto fifth floor lable: 1:1.5:3 (1 cement :1.5 coarse sand : 3 graded stone) (CH-5 S.I. No. 5.1.2 SOR 2020-21)

Reinforcement of Reinforced concrete or reinforced brick work (When not included in and an over all rates) brought to required shape as necessary including bending for proper completion of the work and including the supply of steel and its waistage Bend, hooks, Binding wire and authorized over lapping shall be measured upto floor two level. (S.I. No. 504 SOR 2020-21)

Class-150 brick work in 1:4 Cement and Coarse sand of 2.25 fineness modulous mortar in super structure above plinth level upto floor five level including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cm. (CH-6 S.I. No. 6.1.1 + 6.8A SOR-2020-21)

15mm thick Cement plaster with cement mortar in proportion of 1:4 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm. In girth and finished even and smooth. (CH-13 S.I. No. 13.5.1 SOR 2020-21) 1 cement : 4 Coarse sand

12mm Thick cement plaster in single coat on fair side of single or half brick wall for interior plastering upto floor two level including internal rounded angles not exceeding 80mm in girth, chamfers and finished even and smooth. (CH-13 S.I. No. 13.4.1. SOR-2020-21) 1 cement : 4 Coarse sand

Providing and fixing of 35mm thick ISI marked flush door shutters conforming to IS : 2202 (Part-I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked stainless steel butt hinges with necessary screws, steel handels, Siliding bolt, Door Stopper and tower bolt. (CH-9 S.I. No. 9.21.1 SOR 2020-21)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per (Cost of aluminium snap beading shall be paid in basic item): (CH-9 Item No. 7 SOR 2020-21) i) With float glass panes of 5.5 mm thickness

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (CH-9 S.I. No. 14 SOR 2020-21)

Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. The exposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardent having necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction of Engineer-in-charge. (CH-9 S.I. No. 16 SOR 2020-21)

Fixing to steel or wooden chaukhats in position. (A) Door chaukhats/window chaukhats above 1.5 Sq.m. and upto 5 Sq.M. (CH-10 S.I. No. 10(A) SOR 2017-18)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (CH-10 S.I. No. 14 SOR 2020-21)

S/F fly and mosquto proof stainless steel grade 304 wire mesh gauge with 0.50mm dia wire and 1.40mm wide aperture with matching wood beading etc complete. (CH-1 Item No. 25 (Material) SOR 2020-21)

Providing and laying integral cement based water proofing treatment BIRCK KOBA including preparation of surface as required for treatment of roofs, consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS. 2645 including adjoining walls upto 300 mm height. (b) Laying brick bats with mortar with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 to required slope including rounding of junctions of walls and slabs (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final be flooded with water for a minimum period of two weeks for curing and for final test. With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (CH-11 S.I. No. 2 SOR 2020-21)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part-1) : 2011 (Board with BIS Certification marks (CH-12 S.I. No. 12.45.1 SOR 2019-20)

Providing and laying Ceramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacture) of 1st quality conforming to IS : 15622 of apporved make in colours such as White, lvory, Grey, Fume Red Brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 Coarse sand), Jointing with grey cement slurry@3.3kg/sqm including pointing the joints with white cement and matching pigment etc, complete. (CH-14 Item No. 7 SOR 2020-21)

Providing and laying Vitrified tiles in floor with lean concrete of 600x 600mm sizes (thickness 10mm), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, including grouting of joints. including preparation of 75mm thick base with concrete 1:4:8 complete as per E/I. (CH-14 S.L. No. 15 SOR 2020-21)

Black granite Polished stone flooring with 18mm thick marble stone, as per sample of marble apporved by Engineer-in-charge, over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Black Granite Stone quality. (CH-14 Item No. 8 SOR 2020-21)

Sand filling in plinth including supply of necessary quantity of local sand from a distance not exceeding 8 Kms from the side of work and including watering dressing etc. required for proper completion of work. (CH-4 Item No. 255 SOR 2020-21)

Construction of granual sub base (GSB) by providing coarse graded material spreading in uniform layers with moter grader surface, mixing by mix in place method with rotavator at OMC & compacting with vibratory power roller to achieve the desired density, complete as per clause Table-400-2 S.N. 4.2 (C) MORT&H specification no. 401 (53mm - 26.50mm @ 35%, 26.50-4.75mm @ 45%, 2.36-mm and below @ 20%)

Supply and Laying of 100 mm (Rubber molded Coloured) I shaped precast Interlocking tiles of thickness 60 to 100mm (Compressive strength not less then 30Mpa and weight 4.50kg) Including 25mm thick local sand base levelling and dressing of surface to required level and slope, filling joints with local sand all complete work. (S.I. No. 12 New SOR-2019-20)

Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.25 Ltr/10sqm including one coat of primer applid @ 0.75Ltr/10sqm coat curing and cost of all material, labour, T&P etc. required for proper completion of work.for two coat. (CH-15 Item No. 31 SOR 2020-21)

Finishing walls with acrylic emulsion paint of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work.for two coat. (CH-15 Item No. 30 SOR 2020-21)

Finishing walls with Putty approved brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work. (CH-15 Item No. 27 SOR 2020-21)

Supply and hoisting of 500 Litre Sintex or equivalent high density polyethylene seamless of piece moulded tanks and placing the same in proper position including all taxes, labour and T&P etc. for proper completion of work. Tank should be ISI marked, Sintex or equivalent. (CH-19 S.I. No. 2 SOR 2020-21)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineerin-Charge. External work (CH-23 S.I. No. 9 SOR 2020-21) 32.1 100 mm nominal inner dia pipes

150 mm nominal inner dia pipes

50 mm nominal outer dia pipes

25 mm nominal outer dia pipes

Providing and fixing of 25 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (CH-23 S.I. No. 16 SOR 2020-21)

Providing and fixing of 25 mm nominal bore brass ferrule with C.I. mouth cover including boring and tapping the main : (CH-23 S.I. No. 17 SOR 2020-21)

Constructing masonry Chamber brick work with common burnt clay F.P.S.(non modular) bricks of class designation 150 in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar :3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design (CH-23 S.I. No. 22 SOR 2020-21) 60x60x75 cm Inside

90x90x100 cm Inside

Providing and fixing uplasticised PVC connection pipe with brass unions: (CH-23 S.I. No. 21 SOR 2020-21) 45 cm length 20 mm nominal bore

Providing and fixing of 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931. (CH-23 S.I. No. 22 SOR 2020-21)

Providing and fixing of 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (CH-23 S.I. No. 23 SOR 2020-21)

Providing and fixing of 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (CH-23 Item No. 27 SOR 2020-21)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: (CH-23 Item No. 27 SOR 2020-21)

Providing and fixing of 100mm Stainless Steel grating of approved quality and colour. (CH-23 Item No. 30 SOR 2020-21)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid (CH-24 Item No. 2 SOR 2020-21)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: (CH-24 Item No. 3 SOR 2020-21) White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: (CH-24 S.I. No. 5 SOR 2020-21) Kitchen sink with drain board i) 510x1040 mm bowl depth 250 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (CH-24 S.I. No. 7 SOR 2019-20)

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. (CH-24 S.I. No. 8 SOR 2020-21) Flexible pipe (40mm dia)

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. (CH-27 S.I. No. 1 SOR 2020-21)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (CH-27 S.I. No. 3 SOR 2020-21)

Providing and fixing of 125mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: (CH-27 Item No. 5 SOR 2019-20)

Kota stone slab 20mm thick in risers of steps, skirting dado and pillars laid on 10mm thick cement mortar 1:3 (1 cement : 3 coarse sand) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (CH-14 Item No. 11 SOR-2020-21

P/L 18mm white Agaria stone (super quality) flooring over 25mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry including rubbing and polishing complete. (CH-14 Item No. 9(b) SOR-2020-21

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc complete. (CH-12 S.No. 11(iii) SOR 2020-21)

Electric work Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash. (Code No. 138C SOR 2018)

Wiring point for two ways light with 1.5 sq. mm. F.R. PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire , GP Box and two number two way piano type switches & ceiling rose / angle / batten holder on 3 mm thick phanolic laminated backelite sheet etc., complete in all respect, as directed, including matching colour wash. (Code No. 139C SOR 2018)

Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sqmm PVC insulated single core aluminium conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 8 SWG GI earth continuity wire, piano type switch and ceiling rose on 3 mm. thick phenolic laminated backelite sheet etc, complete in all respect including matching colour wash. (Code No. 140C SOR 2018)

Wiring Point for plug with 1.5 sq. mm. PVC insulated single core aluminium conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 8 SWG GI earth continuity wire, GP Box & piano type switch and socket etc, complete in all respect including matching colour wash. (Code No. 141C SOR 2018)

Wiring Point for call bell with 1.5 sq. mm. PVC insulated single core aluminium conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 8 SWG GI earth continuity wire GP Box ,and piano type bell push or 2 pin socket etc., complete in all respect including matching colour wash. (Code No. 142C SOR 2018)

Wiring point for exhaust fan with 2.5 sq. mm. PVC insulated single core aluminium conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 8 SWG GI earth continuity wire,GP Box , 15A piano type switch & ceiling rose on 3 mm thick phenolic laminated backelite sheet etc, complete in all respect including matching colour wash. (Code No. 144C SOR 2018)

Supply and wiring of submain with two number 6 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit on surface, with one number 14 SWG copper earth continuity wire etc., complete in all respect. (Code No. 212B SOR 2018)

S&F of 63 Amp. 240 V DP metal clad rewireable type switch fuse unit on M.D.F.E.G. / Teak wood board complete in all respect. (Code No. 305 SOR 2018)

Supply and fixing of BEE 5 star rated-1200 mm. sweep ceiling fans with fan motor. (S.I. No. 1501 (i) / 2018)

Supply and fixing of fresh air fan. (S.I. No. 1501 (i) / 2018)

Supply and fixing of 20 watt LED bulb.

Supply and fixing of 22 LED metal body batten fitting complete lumens suitable mounting for on both surface & suspended with 5 years warrantee. complete in all respect. CAT-A 1980 system lumens, 90lm/watt PF0.95 THD10%, CRI80, with 2 year warrantee. (S.I. No. 1413(A) / 2018)

Supply and fixing of Down lighter 12watt.