Agra Development Authority Tender

AMPLIFIER:- Professional Four channel Power amplifier for Speakers, Class H with toroidal power supply, Usable as 4/3/2 ch amplifier, Power output 4x 800W @ 8 ohms, 4 x 1250W @ 4 ohms, 4 x 1500W @ 2 ohms, Bridge Output - 2 x 2500W @ 8 ohm, 2 x 3000W @ 4 ohm, Frequency Response - 20- 20000Hz, Sensitivity - 0.77 / 1 / 1.44 Vrms, Damping Factor: 600, Complete protection circuitry inbuilt. (Make : Celto Acoustique / Martin Audio / d&b audiotechnic/ Lab Gruppen / VAL audio).

AMLIFIER:- Professional Class D Dual channel Power amplifier for Subwoofers, Linear Power supply, Power 2x 1300W @ 8 ohms, 2 x 2500W @ 4 ohms, Frequency Response - 10- 25000Hz, Sensitivity - 1.8Vrms Input Impedance - 20K, Crosstalk - 70dB, S/ N ratio - 110dB, Damping Factor 800, THD - 0.05%. (Make : Celto Acoustique / Martin Audio / d&b audiotechnic/ Lab Gruppen / VAL audio).

DSP:- High-end 4 In x 8 Out Networkable Loudspeaker Management System , High precision 32-bit floating point Top of the line SHARC DSP (96kHz sampling rate), Each output: Routing, Delay, Gain, HPF and LPF filters (up to 48dB/oct), 16 filters (PEQ, Notch and Shelving), 2 Dynamic EQ per channel and 1024 tap FIR filters, Peak Stop and pure RMS Compressor / Limiter (Threshold, Attack, Release, Ratio) (Make : CELTO / MArtin Audio / Analog device / Symetrix).

64 x 64 networked audio channels; Eight on-board channels and GPIO; 8 x AEC (acoustic echo cancellation) processors; USB AV bridging (8 x 8 audio) (Make : CELTO / VAL audio / Martin audio / Lab Gruppen or equivavent).

UCI Deployment license (Make : Customised).

8" or more Touch Screen (Make : Apple/ Dell /Microsoft).

24in / 24out Audio Interface / Sound Card with 8 x Mic Preamps, 2 x JFET Instrument Inputs, 2 x Independent Headphone Outputs, 8 x Line Outputs, 2 x Optical Inputs, 2 x Optical Outputs, Multi-Channel Smart gain, Programmable Function Button, Ultra-Low Latency Software Mixer, Monitor Control, Audio Loop-back, Word Clock Output, Standalone Mode, USB2.0 (USB-C Connection), 24bit / 96kHz, (Make : RME / Biamp / Motu / Audient).

Installation, Programming, Tuning and system alignment charges along with Cables & connectors; SPEAKER CABLE:- Speaker Lines: 2-Core, 2.5 Sq. mm copper conductor Multistranded, PVC insulated in PVC jacket on wall surface/in pipe complete with connection, testing MICROPHONE CABLE:- Microphone lines high grade, professional low noise, 2 core high conductivity PVC insulated in PVC jacket, shielded copper cable with Di- electric insulator both end with XLR m/f connector (Make : Customised).

B - GOBO & LASER PROJECTION SYSTEM SITC of Moving Head Animation Laser : Source - Laser Diode : 30w RGB/RGBY, Power Consumption ≤ 1200w, Scanner - 30kpps, Scan Angle - ±30°, Linearity DIstotion 2%, Beam Diameter And Divergence : 9x6.5mm, 1.2mrad, Rotation : X Axis 540° / Y Axis 270° ,Control modes - Integrated Hardware to Support Animation Software Over ILDA or CAT6 ,Ingress Protection - IP65 . (Make : MARTIN/ LBT / KVANT / ARCTIK / CAMEO).

Laser Programming Software. (Make : LBT / KVANT / Pangolin).

C - PATHWAY & PALACE ILLUMINATION SITC of Outdoor featured customised mini bollard light with FRP housing with the same texture as that of the Fort Stone, embedded with light. Design to be approved by the department. Luminaire Wattage 15-20W (max), Well designed thermal management system with aluminium heat sink Operating Voltage of AC 165-270V 50HZ with universal electronic driver, Light colour should be iny range of 2700-4000K, Mean rated service life L70(tq 25 °C) = 50,000 h.Ingress protection rating (DIN EN 60529): IP65,The luminaire should be provided with Electrical safety class I. Operating Temperature 0 deg to +50 deg The work also includes all the accessories , connections in main LT panel box and of all wires, cable, earthing and MCCB/MCBs as per Engineer-in-Charge with proper metal cages for lights protections. (Make : Customised).

SITC of high quality long through DMX controlled RGBW wash light, Protection Rating : IP66 & IK08, complying to BIS standard IS . Mounting Structure : Additional wall mount yoke arrangements for fixing the lights. Rotation view : Inbuilt body rotating angle in degrees for uniform rotation angle to get the desired effect. Power consumption : 35-40W, (max) CCT : Tunable, (as per the design approval) Beam Angle - as per site requirement, Control : Manual/ON/OFF, Body : Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC 110-230V, 50Hz . Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement) Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass sealed above the glare free unit. Painting : 7 tank processed chemical treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , lifetime should be at least 50,000 burning hours at L70 at 25 degree centigrade with total protection class of IP 66 & IK08 . Luminaire is inclusive of Integral male/female waterproof connectors , driver, accessories for fixing ( nut , bolt , clamps etc ) with structures in pre wired conditions as per IS. The work also includes all the accessories , connections in main LT panel box and of all wires, cable, earthing and MCCB/MCBs as per Engineer-in-Charge with proper metal cages for lights protections. DMX Controlled LED Floodlight Luminaire 75W (DSR & AOR (E&M) ITEMS FOR FAÇADE LIGHTING / 1.8/ Pg1) (Make : Martin/ Traxon/ ColourKinetics/ Arctik / LT/ Jaquar/ Panasonic/Ligman/ iGuzzini/ Cameo / ROXX lighting).

SITC of high quality long throw DMX controlled RGBW wash light, Protection Rating : IP66 & IK08, complying to BIS standard IS . Mounting Structure : Additional wall mount yoke arrangements for fixing the lights. Rotation view : Inbuilt body rotating angle in degrees for uniform rotation angle to get the desired effect. Power consumption : 70-80W (max), CCT : Tunable, (as per the design approval) Beam Angle - as per site requirement, Control : Manual/ON/OFF, Body : Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC 110-230V, 50Hz . Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement) Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass sealed above the glare free unit. Painting : 7 tank processed chemical treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , lifetime should be at least 50,000 burning hours at L70 at 25 degree centigrade with total protection class of IP 66 & IK08 . Luminaire is inclusive of Integral male/female waterproof connectors , driver, accessories for fixing ( nut , bolt , clamps etc ) with structures in pre wired conditions as per IS. The work also includes all the accessories , connections in main LT panel box and of all wires, cable, earthing and MCCB/MCBs as per Engineer-in-Charge with proper metal cages for lights protections. DMX Controlled LED Floodlight Luminaire 75W (DSR & AOR (E&M) ITEMS FOR FAÇADE LIGHTING / 1.8/ Pg1) (Make : Martin/ Traxon/ ColourKinetics/ Arctik / LT/ Jaquar/ Panasonic/Ligman/ iGuzzini/ Cameo / ROXX lighting).

SITC of high quality long throw DMX controlled RGBW linear wash light, Protection Rating : IP65, complying to BIS standard, Mounting Structure : Additional wall mount yoke arrangements for fixing the lights. Rotation view : Inbuilt body rotating angle in degrees for uniform rotation angle to get the desired effect. Power consumption : 40-50W (max), CCT : Tunable, (as per the design approval) Beam Angle - as per site requirement, Control : Manual/ON/OFF, Body : Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC 110-230V, 50Hz , Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement) Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass sealed above the glare free unit. Painting : 7 tank processed chemical treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , lifetime should be at least 50,000 burning hours at L70 at 25 degree centigrade with total protection class of IP 66 & IK08. Luminaire is inclusive of Integral male/female waterproof connectors , driver, accessories for fixing ( nut , bolt , clamps etc ) with structures in pre wired conditions as per IS.LED Driver, IP65 or higher, IK05 or higher etc. The work also includes all the accessories , connections in main LT panel box and of all wires, cable, earthing and MCCB/MCBs as per Engineer-in-Charge with proper metal cages for lights protections. DMX Controlled LED Linear Wallwasher light 40W (DSR & AOR (E&M) ITEMS FOR FAÇADE LIGHTING / 1.10/ Pg1) (Make : Martin/ Traxon/ ColourKinetics/ Arctik / LT/ Jaquar/ Panasonic/Ligman/ iGuzzini/ Cameo / ROXX lighting).

Stand Alone DMX controller with Zone management and 16-bit channel management. RDM Enabled. Extensive external triggering operations via Dry Contact ports, TCP/UDP along with Calendar Triggers. Ethernet Integration. IOS/Android APP based wireless control. 1024 DMX channel control with an option to get a paid upgrade to 2048 channels. DC5-5.5V Input via external adaptor. Up to 32BG memory. Using light show authoring software to select from standard 10 effects, adjust effect settings such as color, speed, and brightness. (Make : Arctik / Cameo /Claypacky / Avolite / Enttec/ Madrix).

SITC of CAT6 To DMX Converter Or Artnet: 2 Universe, Supports RDM and DMX 512, IP20, Tray Mounting Available. (Make : Arctik / Cameo /Claypacky / Avolite / Enttec/ Madrix).

Signal Amplifier and Splitter: 8 Channel, Supports RDM and DMX 512, IP20, Tray Mounting Available. (Make : Arctik / Cameo /Claypacky / Avolite / Enttec/ Madrix).

D - ELECTRICAL ITEMS SITC of customised waterproof power junction box /power cable terminal box, IP65 made up of rugged, non-corrosive, high impact polycarbonate, moulded nylon encases connectors that use screw compression to secure the wires, protection against water jets and dust from all directions, with bus bar and MCB 10A. (Make : customized).

SITC of DC power driver for the above Lights, Power : 200W, Input : AC 110-240V AC, 50Hz, Output : DC 12/24V, Protection rating, IP65, Surge protection : LL 4KV, LE 6KV (Make : Meanwell/ GE/ Osram/ Cree).

SITC of MS Fabricated IP 65 driver Box having IP67 glands for incoming and outgoing power connections as per the project requirement. Wall mounting arrangements with the clamps. Easy of driver mounting, termination having fixing arrangements and door with rubber gasket & locking system (Make : customized).

Supply & Erection of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entries Electrical control panel with TPN ACB(65 KA,4Pole Elect draw out , Micro processer Release IPR2 ) and TPN MCCB's (Four Pole 36 KA with thermal magnetic release) Switches and instrument chamber etc. Complete in all respects. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses, current transformer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/ DMC support with detachable side covers and shall be suitable for extension on the sides. The switches entry boxes shall be complete with suitable cable end boxes reverse. Incoming 630 Amp /415Volt ACB- 1 No, Outgoing 100 Amp.MCCB-5 Nos., & 63 Amp.MCCB-1No,Cat. A.Pannel Cubicle Type, SOR (821(a) (Make : MDS, Standard, Indo Asian, Havell's, HPL, Legrand, Cona, Bentec, Polycab).

The Job includes the grouting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above Will be provided with Amp Metre, current transformers and selector switches etc and instrument fuse. The switch board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2mm. Cubicle type switch board shall be of cat A & B Only. (Make : customized).

True on-line 60 kVA or higher UPS with 3 Ph double Conversion - 3 ph. input/3 ph. output with 20/25/30 kVA hot swappable modules with suitable capacity sealed maintenance free 12 V batteries, with a 15 mins backup time on full load with MS open MS Battery rack and Nyvin cable. (Make : Delta/ Schneider/ Vertiv).

Supply & Installation of Stone fitments, in buff sandstone to match with the existing texture of the monument, with special adhesive for Luminaire installations. Size: length between 15cm to 30cm, width between 10 cm to 20cm & height of approx 5cm or as per site requirement & to be verified by Engineer-in-charge. (Make : customized).

Supply & Installation of Stone fitments, in buff sandstone to match with the existing texture of the monument, with special adhesive for Luminaire installations. Size: length between 50cm to 1.2m, width between 10 cm to 20cm & height of approx 5cm or as per site requirement & to be verified by Engineer-in-charge. (Make : customized).

Supply & Installation of 4 nos. 25 sq mm FRLSH PVC insulated copper conductor cable. (Make : Polycab/ Finolex/ Havells).

3C X 4 Sq.mm. PVC insulated, PVC sheathed, armoured/unarmoured, and stranded copper conductor cable 1100V grade, of ISI Marked as required. (Make : Polycab/ Finolex/ Havells).

PVC conduit with one number 1.5 sq. mm. multistrand copper conductor cable as earth continuity wire drawn in conduit. (Make : Polycab/ Finolex/ Havells).

Laying of ISI Marked Aluminium Armoured PVC insulated and PVC sheathed / XLPE power cable of 1.1KW grade of above mentioned size direct in ground or pipe or trench as required including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Excavation Works for laying of cables.(As per actuals depending upon the site condition).

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth (As per actuals depending upon the site condition) (Make : Polycab/ Finolex/ Havells)

Supply and fixing 25mm MS grey box conduit ISI marked FRLS along with the accessories in concealed system etc. as required. The colour to be matched with the monument texture. (Make : Polycab/ Finolex/ Havells).

Supply installation testing and Commissioning of DMX Wire 2Core Shielded cable Network wiring consists of a shielded twisted pair, with a characteristic impedance of 120 ohms, with a termination resist or at the end of the cable farthest from the controller to absorb signal reflections. (Make : Extron/ D'Link/ Kramer).

CAT 6 Shielded Twisted Pair cable for signal & data transmission. 24 AWG twisted pair conductors inside an overall braid and foil shield. Shielded Twisted Pair cable should provide added protection from outside interference and ensures high quality signal transmission. (Make : Extron/ D'Link/ Kramer).

Installation, programming & Commissioning of the Illumination system in the non-intrusive manner. This shall include Scaffolding/ mounting arrangements & all the necessary accessories required for connections & installations viz. cables/ junctions boxes, connectors etc.

E - Operation & Maintenance charges Operation & Maintenance charges for 1st year (@0% of cost)

Operation & Maintenance charges for 2nd year (@1.5% of cost)

Operation & Maintenance charges for 3rd year (@2.5% of cost)