Agra Development Authority Tender

Class-150 (Non Modular) brick work in 1:4 Cement and coarse sand mortar in foundation and plinth including supply of all materials, labour and T & P etc. required for proper completion of the work. As per direction of E/I.(Ch-6 Item No. S.I.No.2 SOR 2020-21)

Providing and laying D.P.C. 25mm thick with Cement concrete Consisting of One Part Cement, 1.5 Part of Coarse Sand and three part of approved 10mm grade stone grit and including water proofing material as directed by the Engineer-In-Charge in the proportion as specified by the manufacturer. (Ch-7 Item No. S.I.No.2 SOR 2020-21)

Same as Item No. (3) above but in super structure above plinth level upto floor five level (upto five stories) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cm. (Ch-6 Item No. S.I.No.2+5 SOR 2020-21)

Red sand stone work for wall lining etc. (Veneer work) 30mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) including camping jointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.(Ch-18 Item No. S.I.No. 1 SOR 2020-21)

Same as Item No. (3) above but in super structure above plinth level upto floor five level (upto five stories) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cm. (Ch-6 Item No. S.I.No.2+6 SOR 2020-21)

Mild steel of iron in heavy sizes such as trusses, built up gates record rack, roof work, gates etc. brought to required form including drilling holes revitting or welding where necessary, and also including supply of steel bolts, nuts, wastage etc. and their fixing require for proper completion of the work. (Chapter-10 SI. No.503) SOR 2020-21

Supply and fixing of flush doors, commercial quality conferming of I.S. 2202 part-1 (1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges, bolts, locks, handles, springs, fitting with necessary screws to be supplied departmentally (Chapter-9 SI. No.470(ii)) SOR 2020-21

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per (Cost of aluminium snap beading shall be paid in basic item): (ii) With float glass panes of 5.5 mm thickness (Chapter-9 SI. No.8(ii)) SOR 2020-21

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified (Chapter-12 SI. No.9 SOR 2020-21

12 mm thick cement plaster in single coat on fair side of single or half brick wall for interior plastering uoto floor two level including internal rounded angles not exceeding 80 mm in girth, chamferes and finished even and smooth. (NBO-17.58) 1 cement : 4 coarse sand (CH-13 S.I. No. 2 SOR 2020-21

Finishing walls with Putty approved brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work. (Chapter-15 SI. No. 27 New SOR 2020-21)

Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.25 Ltr/10sqm including one coat of primer applid @ 0.75Ltr/10sqm coat curing and cost of all material, labour, T&P etc. required for proper completion of work.for two coat. (CH-15 Item No. 31 NEW SOR 2020-21)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per anufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks) (Ch-12 SI No. 8 SOR 2020-21)

Sand filling in plinth excluding supply of necessary quantity of sand from a distance not exceeding 8 Kms from the side of work and including watering dressing etc. required for proper completion of work (Lead upto 30m & lift 1.5m) (labour only) (CH-4 Item No. 6 NEW SOR 2020-21)

Providing and laying cement concrete in 1:2:4 of not less than strength of M-150 Stone ballast (40 mm nominal size) approved coarse sand and cement, curing complete, Including cost of form work. In Foundation and floors. (CH-5 Item No. 6 NEW SOR 2020-21)

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade II (glass fibre base self finished bitumen felt) and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading, complete.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.(CH-24 Item No. 1 NEW SOR 2020-21)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever require: (A) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C. P. brass pillar taps (CH-24 Item No. 3a NEW SOR 2020-21)

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. Flexible pipe 40 mm dia (CH-24 Item No.8 (b)ii NEW SOR 2020-21)

HEP Nahani trap of Indian make HCI 100x75mm (CH-22 Item No.68 NEW SOR 2020-21)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931. 15 mm nominal bore (CH-23 Item No.22 NEW SOR 2020-21)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore (CH-23 Item No.26 NEW SOR 2020-21)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineerin-Charge. External work (CH-23 Item No.9 (A) (C) SOR 2020-21) 16 mm nominal outer dia pipes

25 mm nominal outer dia pipes

Providing and fixing PVC pipe conforming to IS make working pressure 6 Kg/SqCm incuding testing labour T&P and all complete fittings 75 mm diameter

110 mm diameter

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm (CH-24 Item No.23 NEW SOR 2020-21)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. (CH-14 Item No.7 NEW SOR 2020-21)

Providing and laying Vitrified tiles in floor of 500x 500mm sizes (thickness 10mm), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in desired colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, including grouting of joints. (CH-14 Item No.15 NEW SOR 2020-21)

Providing and Laying 25mm kota stone flooring over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid over jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. (CH-14 Item No.10 NEW SOR 2020-21)