Public Works Department Tender

Tack coat:-( iii ) Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface treated with primer & cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503.

Tack coat:-( i ) Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503.

Bituminous Concrete: Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.40 Percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects. B. Grading II, i). With Viscosity Graded Bitumen of VG-30.

Traffic Signs (using jhama brick aggregate in CC/ PCC) A. Retro-reflectorised Traffic Signs 1) Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide MoRD technical specification Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete (using jhama brick aggregate) 450 mm x 450 mm x 600 mm,600 mm below ground level as per approved drawings and MoRD Technical Specification Clause 801. (i ) with 900 mm equilateral triangle aluminium sheeting

(iii ) with 600 mm circular aluminium sheeting

Direction and Place Identification signs upto 0.9 sqm size board (using jhama brick aggregate in CC / PCC) ( B ) Semi Reflective Traffic Signs:-Providing and erecting and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm thick M.S. sheet duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 70 mm width and required message, letters and figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47 mm x 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete (using jhama brick aggregate) 450mm x 450 mm x 600 mm, 600 mm bellow ground level as per approved drawings and MoRD Technical Specification Clause

Road Safety Convex Mirror Providing and fixing pole mounting (50 mm dia steel pole of standard height) 800 mm dia strong unbreakabale highly reflective road safety convex mirror body made up of poly carbonate having large viewing angle from standard distance (minimum 6 m) firmly fixed to the gound by means of properly designed foundation with M-15 grade cement concrete 450mm x 45mm x 600 mm as per IRC guideline/ MoRT&H Technical Specification Clause 801.

Painting lines, Dashes, Arrows, etc. on Road in Two Coats on New Work:-Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and MoRD Technical Specification Clause 1702.

80 mm thick factory made c.c. interlocking paver block of M-35 Grade:-Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern.

Earthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 including settingout, constructionof shoring&bracing, removal of stumps & other deleterious material and disposal upto a lead of 50m,dressing of sides & bottom and back filling in trenches with excavated suitable material.I Ordinary Soil (i) Upto 3 m depth

Filling in foundation trenches as per drawing &MoRD technical specification Clause 305.3.9, 1200. I Sand filling

Providing concrete for plain/reinforced concrete in open foundationscomplete including form work as per drawings &MoRD technical specifications Clauses 802, 803, 900, 1202 and1203. (including centering, shuttering, staging etc. but excluding reinforcement). I P.C.C grade M 10 ,(i) Nominal mix 1:3:6

Providing concrete for plain/reinforced concrete in open foundationscomplete including form work as per drawings &MoRD technical specifications Clauses 802, 803, 900, 1202 and1203. (including centering, shuttering, staging etc. but excluding reinforcement). III P.C.C grade M 20 ,(i) Nominal mix 1:2:4

Supplying, fitting&placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in foundation complete as per drawings &MoRD technical specifications Clauses 1000 & 1202.

Road Markers/Road Stud with Lense Reflector:- Providing and fixing of road stud 100 x 100 mm, die-cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973

Road side Pucca Drains:- Construction of road side pucca drain with M10 (1:3:6 with jhama brick aggregate) to specified lines, grades, levels and dimensions as per approved design and MoRD Technical Specification Clause 307, 1606. Excavated material to be used in embankment at site. (including centering, shuttering, etc. but excluding reinforcement) C. Trapezoidal drain (top clear width 600 mm, bottom clear width 300 mm and clear depth of 600 mm) I. In Ordinary Soil