Public Works Department Tender

Providing & installation of 76.00 mtr head water lubricated submerssible pump with 3 Ph , 415 VAC motor with star delta connection along with PVC insulated 3 core flat Copper cable conforming to relevant IS code for submerssible motor with all necessary equipments and fittings as required upto the depth of 80 ft to 100 ft by 100 mm dia GI pipe welded with GI flange in/c providing fitting fixing by necessary rubber washer, nuts & bolts, MS safety clamp etc. as per required size and making necessary electrical connection with main switch / starter with motor in/c mmissioning & trial run as per direction of the Engineer-in-charge (each pump with motor shall consist of stainless steel impeller conforming to relevant BIS code. pump make : uke/KSB/WPIL/Texmo/CRI/Calama) (Pumpset, cable, necessary fittings etc. for GI column pipes will be supplied by the agency at his cost and for GI Column pipe assembly of 100 mm dia welded with necessary GI Flanges / main switch / starter payment will be done separately).

Providing and fitting fixing of 6 feet x 4 feet x 1 inch (thickness) Gamair wood / plywood pannel board for fitting fixing of electrical items, in/c 2 nos MS angle post ( size 2 inch x 2 inch x 9 feet ), nuts & bolts etc. for irrection of the same by 1:1.5:3 cement concrete casting ( 1 feet x 1 feet x 2 feet) below the ground level and painting two or more coats & plastic paint as per specification and direction of the Engineer-in-charge.

Providing and fitting fixing steel sheet enclosed switch fuse unit (suitable for DIN fuses), triple pole with Neutral Link (TPN), 415/500 Volt, L & T / Havells / BCH make etc. complete as per specification and direction of the Engineer- in-charge. 63 Amps

Providing and fitting fixing of Fully Automatic Star Delta type Motor starter ( 3 ph. 50 Hz, 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge. i. 25 HP/18.5 kw Relay range within 13-21 + 10%

Providing and fitting fixing of moving iron type, Range 0-500 V, 96 mm x 96 mm size AC Volt meter ( L & T / AE make)with selector switch as a electrical instrument of the pannelboard as per specification and direction of the Engineer-in- charge.

Providing and fitting fixing of moving iron type, Range 0-100 A, 96mm x 96 mm size AC Amps meter direct reading type ( L & T / AEmake) with selector switch and CT coil as a electrical instrument of the pannel board as per specification and direction of the Engineer-in-charge.

Providing and fitting fixing 3 phase indicating lamp fiited with panel board with three different colour lamps with batten holder complete as per specification and direction of the Engineer-in-charge.

Providing and fitting fixing of Moulded Case Circuit Breaker(MCCB) of different Thermal release range , 415 + V, 50HzL & T, BCH, ABB make) as per specification and direction ofthe Engineer-in-charge. 25-32 Amps

Providing and fixing G.I. Bend /eIbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. 125 mm dia

Providing, fixing and laying fabricated UPVC socket / coupler conforming to IS : 10124 ( Part 2 ) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. 90 mm dia

110 mm dia

140 mm dia

160 mm dia

Providing and fixing C.I. sluice valves ( with cap ) completewith bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge. 125 mm dia PN - 1.0

150 mm dia PN - 1.0

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level: 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Local Teak Wood

Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge. Local Teak wood 35 mm thick shutters

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150 x 10 mm

Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc. complete 250 x 16 mm

Cement concrete flooring 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. all complete etc as per direction of Engineer-in-charge. 40 mm thick with 20 mm nominal size stone aggregate

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete as per direction of Engineer-in-charge. 0.63mm thick with zinc coating not less than 275gm/m2

Providing and fitting G.C.I sheet (0.63 mm thick) for walling including Vertical/curved surface fixed with galvanized steel J or L hooks 8 mm diameter, bolts and nuts with bitumen and G.I limpet washers or with G.I. limpet Washers filled with white lead and including a coat of appoved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/Verticle or curved surfaces ) excluding the cost of G.S. sheet purlins rafters and trusses and including cutting to size and shape wherever required as per direction of Engineer -in-Charge.

Providing and laying different dia rigid UPVC pipes of Working Pressure 4.0 kg/ sq.cm. complete with necessary coupler and solvent cement as per CPWD Specification & direction of Engineer-in-charge. 90 mm dia

110 mm dia

140 mm dia

160 mm dia

Providing and fitting fixing of G.I hydrant suitable for PVC pipes as per standard specification complete as per direction of Engineer-incharge (Rate excluding the cost of NTP control valve). 80X50 mm dia

Labour charge for repairing of leakage in existing UPVC distribution system including required earth cutting and fitting fixing of necessary coupler etc. complete and refilling the trench with available excavated earth as per direction of the Engineer-in-charge. (Payment of couplers, tees, reducers etc will be made separately) 250 mm dia to 110 mm dia.

90 mm dia.