Public Works Department Tender

Providing and laying flat brick brick soling layer on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering and rolling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412.

Providing and laying brick edging laid lengthwise on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering and rolling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412.

1) WBM Grading 3 Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading- 3 as per MoRD Technical Specification Clause 405.. A. By Manual Means

Patch repairing/Maintenance of bituminous surface road using Jhama brick aggregate & Viscosity Graded bitumen (VG-30) Repairing pot holes and making up small depressions with ramming or power rolling after removal / disposal of disintegrated materials within a lead of 50 m, cutting pot holes to regular shapes with vertical edges and levelling the bottom, cleaning the same with compressed air or any appropriate method including screening, cleaning of aggregates; annd filling up with jhama chips using bitumen of VG-30 @ 54 Kg per cum of loose volume of jhama brick chips, after applying tack coat of bitumen on sides and bottom @ 0.75 kg/sqm and finishing the top of required surface levelled with adjoining area in proper grade and camber including spreading of sand @ 0.006 cum/sqm of prepared road surface as per direction of the Engineer-in-charge and all as per MoRD technical specification Clauses 1900,502,503,504.

Tack coat using hot straight run bitumen of grade VG30 on WBM Providing and applying tack coat using hot straight run bitumen of grade VG30 including heating the bitumen , spraying the bitumen, cleaning and preparing the existing road surface the existing road surface as per specification on WBM @ 0.75 kg / sqm

Tack coat using hot straight run bitumen of grade VG30 on Bituminous surface Providing and applying tack coat using hot straight run bitumen of grade VG30 including heating the bitumen , spraying the bitumen, cleaning and preparing the existing road surface the existing road surface as per specification on Bituminous surface @ 0.50 kg / sqm

Providing , laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base , including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 508. Case - I: By Manual Means i) Bitumen (60/70 Grade)VG-30

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 510 A. By Manual Means Case - IV : Type D (premix with fine sand) i) Bitumen (60/70 Grade)VG-30

Single bamboo palasiding/walling of whole 2nd class bamboo (Jati or Bethua) 65 to 75 mm dia and closely packed and driven @150 mm c/c including fitting fixing with half bamboo kamis horizontally in three rows with cane or tying with wire complete and struts 1.5 m apart longitudinally and providing bitumen drum sheet walling fixed with nails as per drawing and MoRD technical specification Clause 1302.5 A) Driven atleast 900 mm below ground and 1200 mm above ground on average

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification Clause 301.5

Providing and placing gunny / polythene (of minimum wall thickness of 500 micron) bags filled with sand (of minimum qty of 0.034 cum) and properly manually stitched to avoid any leakage of sand as per specificartion.