The Singareni Collieries Company Limited Tender

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Conveyance charges of Earth for 3 KM lead.

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Earth work excavation for foundations and depositing on bank for all lifts and with an initial lead up to 50m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting, etc. complete for finished item of work as per SS - 20 B (APSS 308) - Ordinary soils-Mechanical Means -Up to 3 m depth

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Providing and Laying of Hot applied Thermoplastic compound 2.5mm thick including Reflectorising Glass Beads @ 250 gms per Sqm area, thickness of 2.5mm (exclusive of surface applied glass beads) as per IRC : 35. The finished Surface to be level, uniform and free from streaks and holes. (as per Technical specification 803 of MoRTH) (Make and Paint : BERGER/ASIAN/KATALINE/AUTOMARK, etc., ) Note:- 1). A Sealing primer may be applied in advance on Cement Concrete pavement to ensure proper bonding. Any laitance and / or curing compound to be removed where paint is required to be applied on New concrete surface 2). The contractor shall guarantee the road marking performance for 2 years

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Supplying and Fixing of Moulded Shanks Raised Pavement Markers (Road Studs) made of plastic body moulded from HIPS (HI Impact Polystyrene) or ABS or ASA and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 â?? DO III Dt 11.06. 1997. The height and width shall not exceed 20 mm and 130 mm with minimum reflective area of 13 Sq.Cm on Each side and the slope to the base shall be 35 +/- 5 degree. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturerâ??s recommendation and complete as directed by the engineer (Make: M/s. 3M India Ltd., Ms. Avery Dennison Pvt. Ltd., etc.,) Note:- The contractor should produce 2 years in field performance certificate from manufacturer.

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Supply of Separation Membrane of impermeable plastic sheeting 150 micron thick

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Filling of pot holes in BT road by cutting the road surface up to 75mm depth and to the rectangular or square shape, laying tack coat of Bitumen VG-10, spreading 40mm metal, spraying bitumen over metal, spreading 10mm metal at 0.13 Cu.m/ 10Sqm, rolling, spreading sand including supply of metal and sand etc., as directed by the Engineer-in-charge. (Excluding Cost of Bitumen). Material required per Sqm :- Bitumen VG-10 : 2.28Kg , 40mm Metal: 0.08125Cum, 10mm metal : 0.013 Cum, Sand: 0.006Cum

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Conveyance charges of Bitumen - Bulk Note:- For calculating Kilometres, Round the trip i.e., to and fro distance is to be considered.

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Providing and laying bituminous concrete 30mm to 40mm thick using VG-30 Bitumen with hot mix plant using crushed granite aggregates of 13.2mm nominal aggregate size grading -II as per Table 500-17 of MORTH, premixed with bituminous binder @ 5.4 per cent of mix and filler, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per Technical specification 507 of MoRTH complete in all respects (Excluding Cost of Bitumen) (Material required per Cum : Bitumen-127.225Kg, 13.2mm to 10mm - 0.4458Cum, 10mm to 5mm - 0.3715Cum, 5mm and below - 0.6389Cum, filler - 0.02972Cum)

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Providing and laying dense graded bituminous macadam 50mm to 75mm thick using VG-30 Bitumen with hot mix plant using crushed aggregates of grading-II nominal aggregate size 26.5mm as per Table 500-10 of MORTH, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per Technical specification 505 of MoRTH complete in all respects. (Excluding Cost of Bitumen) (Material required per Cum : Bitumen- 103.85Kg, 25mm to 10mm - 0.4408Cum, 10mm to 5mm - 0.4114Cum, 5mm and below - 0.5877Cum, filler - 0.0294Cum)

BOQ 2 Repairs to road by providing renewal coat from Post office to Central workshop;Laying of tack coat with VG-10 bitumen @ 2 kg/10 Sqm on Bituminous surface including heating of bitumen to the appropriate range with self heating arrangements and spraying tar with nozzles and applying uniformly with aid of bitumen pressure distributor including labour charges, hire and operational charges of T and P and all other operational and contingent charges necessary to complete the finished item of work to the specifications including cleaning of existing surface with mechanical broom as per Technical specification No. 503 of MORTH and as directed by the Engineer-in-charge. (Excluding Cost of Bitumen)

Internal roads at Kothagudem Corporate;Supply of Bitumen 60/70 (VG-30)(Bulk) as on 16.12.2024 (Inclusive of 13.615% CPoH)

Internal roads at Kothagudem Corporate;Supply of Bitumen 80/100 (VG-10)(Bulk) as on 16.12.2024 (Inclusive of 13.615% CP and OH)

Internal roads at Kothagudem Corporate;Laying of tack coat with VG-10 bitumen @ 2.50 kg/10 Sqm on Granular surface including heating of bitumen to the appropriate range with self heating arrangements and spraying tar with nozzles and applied uniformly with aid of bitumen pressure distributor including labour charges, hire and operational charges of T and P and all other operational and contingent charges necessary to complete the finished item of work to the specifications including cleaning of existing surface with mechanical broom as per Technical specification No. 503 of MORTH and as directed by the Engineer-in-charge. (Excluding Cost of Bitumen)

Internal roads at Kothagudem Corporate;Construction of Granular sub-base by providing HBG material confirming to Grading - VI of MoRTandH Table 400-1 including cost and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavator / approved means at OMC and compacting with vibratory roller to achieve the desired density etc., complete for finished item of work as per Technical specification 401 of MORT and H and as directed by the Engineer-in-charge. (Material required per Cum : 53mm to 9.5mm metal -0.448cum; 9.5mm to 2.36mm metal - 0.608cum; 2.36mm and below metal - 0.224Cum)

Internal roads at Kothagudem Corporate;Earth work excavation for foundations and depositing on bank for all lifts and with an initial lead up to 50m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting, etc. complete for finished item of work as per SS - 20 B (APSS 308) - Ordinary soils-Mechanical Means -Up to 3 m depth

Internal roads at Kothagudem Corporate;Providing and Laying of Hot applied Thermoplastic compound 2.5mm thick including Reflectorising Glass Beads @ 250 gms per Sqm area, thickness of 2.5mm (exclusive of surface applied glass beads) as per IRC : 35. The finished Surface to be level, uniform and free from streaks and holes. (as per Technical specification 803 of MoRTH) (Make and Paint : BERGER/ASIAN/KATALINE/AUTOMARK, etc., ) Note:- 1). A Sealing primer may be applied in advance on Cement Concrete pavement to ensure proper bonding. Any laitance and / or curing compound to be removed where paint is required to be applied on New concrete surface 2). The contractor shall guarantee the road marking performance for 2 years

Internal roads at Kothagudem Corporate;Supplying and Fixing of Moulded Shanks Raised Pavement Markers (Road Studs) made of plastic body moulded from HIPS (HI Impact Polystyrene) or ABS or ASA and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 â?? DO III Dt 11.06. 1997. The height and width shall not exceed 20 mm and 130 mm with minimum reflective area of 13 Sq.Cm on Each side and the slope to the base shall be 35 +/- 5 degree. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturerâ??s recommendation and complete as directed by the engineer (Make: M/s. 3M India Ltd., Ms. Avery Dennison Pvt. Ltd., etc.,) Note:- The contractor should produce 2 years in field performance certificate from manufacturer.

Internal roads at Kothagudem Corporate;Conveyance charges of Bitumen - Bulk Note:- For calculating Kilometres, Round the trip i.e., to and fro distance is to be considered.

Internal roads at Kothagudem Corporate;Providing and laying dense graded bituminous macadam 50mm to 75mm thick using VG-30 Bitumen with hot mix plant using crushed aggregates of grading-II nominal aggregate size 26.5mm as per Table 500-10 of MORTH, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per Technical specification 505 of MoRTH complete in all respects. (Excluding Cost of Bitumen) (Material required per Cum : Bitumen- 103.85Kg, 25mm to 10mm - 0.4408Cum, 10mm to 5mm - 0.4114Cum, 5mm and below - 0.5877Cum, filler - 0.0294Cum)

Internal roads at Kothagudem Corporate;Providing and laying bituminous concrete 30mm to 40mm thick using VG-30 Bitumen with hot mix plant using crushed granite aggregates of 13.2mm nominal aggregate size grading -II as per Table 500-17 of MORTH, premixed with bituminous binder @ 5.4 per cent of mix and filler, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per Technical specification 507 of MoRTH complete in all respects (Excluding Cost of Bitumen) (Material required per Cum : Bitumen-127.225Kg, 13.2mm to 10mm - 0.4458Cum, 10mm to 5mm - 0.3715Cum, 5mm and below - 0.6389Cum, filler - 0.02972Cum)

Internal roads at Kothagudem Corporate;Filling of pot holes in BT road by cutting the road surface up to 75mm depth and to the rectangular or square shape, laying tack coat of Bitumen VG-10, spreading 40mm metal, spraying bitumen over metal, spreading 10mm metal at 0.13 Cu.m/ 10Sqm, rolling, spreading sand including supply of metal and sand etc., as directed by the Engineer-in-charge. (Excluding Cost of Bitumen). Material required per Sqm :- Bitumen VG-10 : 2.28Kg , 40mm Metal: 0.08125Cum, 10mm metal : 0.013 Cum, Sand: 0.006Cum

Internal roads at Kothagudem Corporate;Laying of tack coat with VG-10 bitumen @ 2 kg/10 Sqm on Bituminous surface including heating of bitumen to the appropriate range with self heating arrangements and spraying tar with nozzles and applying uniformly with aid of bitumen pressure distributor including labour charges, hire and operational charges of T and P and all other operational and contingent charges necessary to complete the finished item of work to the specifications including cleaning of existing surface with mechanical broom as per Technical specification No. 503 of MORTH and as directed by the Engineer-in-charge. (Excluding Cost of Bitumen)