Telangana State Seeds Development Corporation Limited Tender

AS PER TENDER DOCUMENT;Misc. i.e. floor trap jallis, sanitary/water supply fixtures, cement, sand & other unforeseen, Labour charges for plumber, tiles dismantling, lifting charges of 2nd floor removal of debries from site, cleaning of site after post completion of works etc complete for finished item of work.

AS PER TENDER DOCUMENT;Supplying and fixing of 25.4mm dia , 609.6mm long aluminium anodized towel rods with brackets and aluminium screws including cost and conveyance of all materials, labour charges etc., complete for finished item of work.

AS PER TENDER DOCUMENT;S&F of 15mm dia PVC connection with brass union nut CP coated complete finished item of work

AS PER TENDER DOCUMENT;Supplying and fixing Indian make Flat Back Wash Hand Basin (HSW/Parryware/ Neycer) 1st quality conforming to IS:2556-Part-4:1972 of size 550mm x 400mm with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams Seiko/ Esso or equivalent complete with standard CI brackets including wooden block ,1 No.12.70mm PVC connection with brass union nuts CP coated , 1 No.12.70mm NP bib tap 300 gms Seiko or equivalent including cost and conveyance of all materials to site, labour charges etc. complete for finished item of work

AS PER TENDER DOCUMENT;S&F of Chromium plated finish brass body quarter turn Bibcock cum Health Faucet with 1m long tubeand wall hook with 10 yearswarranty

AS PER TENDER DOCUMENT;S&F of Indian make stop cock/valve complete finished item of work.

AS PER TENDER DOCUMENT;S&F of 15 mm premium variety Chromium plated finish brass body wall mixer with hand shower with a provision for over head shower with 115 mm long bend pipe on upper side, connecting legs & wall flanges conforming to IS 8931 with 10 years warranty

AS PER TENDER DOCUMENT;S&F CP finishe shower complete finish item of works(MR)

AS PER TENDER DOCUMENT;Supplying and fixing CP finish brass soap dish of approved make ISI quality with NP screws etc., complete including cost and conveyance of all materials, labour charges for fixing etc., complete for finished item of work in all floors as per ssr item no 598.

AS PER TENDER DOCUMENT;Supply, Installation and commissioning approved make wash down wall mounted EWC conforming to IS:2556 (Part 16)-2002 with 'P' or 'S' trap with concealed flush cistern fixed in wall with all internal parts of dual flush cistern, ultra solid seat cover of approved make with rubber buffer and cap all of approved make etc. complete for finished item of work in all respects: White colour

AS PER TENDER DOCUMENT;Flooring with Non-skid red suitable or white full body Ceramic floor tiles of size 300 x 300 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs set over a base coat of CM (1:8) prop. 12mm thick including neat cement slurry of honey like consistancy spread at the rate of 3.3kg per sqm and filling the joints with white cement mixed with pigment of matching shade to match the shade of tiles over a bed of C.C. or R.C.C. slab, including cost and conveyance of all materials like cement, sand, water, ceramic tiles, white cement etc., to site (excluding cost of C.C. bed) excluding seigniorage charges on all materials but including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer-in-charge curing etc., including overheads and contractor profit complete for finished item of work. (APSS No.707 & 701)

AS PER TENDER DOCUMENT;Cost, supply and laying of specified and required wiring for light fixtures, AC's etc and providing of switches, switch boards, sockets etc including cost of material, transportation, taxes, labour for laying etc complete finished item of work

AS PER TENDER DOCUMENT;Labour charges for removal, refixing and gas updating of old AC's 4 Nos.

AS PER TENDER DOCUMENT;Cost, supply and fixing of LED tube lights(20 Watts) fixture

AS PER TENDER DOCUMENT;Supply and Transportation of 36W Edge lit 2' x2' (600mm x 600mm) Slim panel LED luminaire Square Housing Made of Aluminum alloy with corrosion resistant powder coat CROMTON make with warranty(As per quotation).

AS PER TENDER DOCUMENT;Cost, supply and fixing of LED lights(15 Watts) for ceiling of size 1'x1'

AS PER TENDER DOCUMENT;Supplying and fixing Gyp Board Fine Line Grid false ceiling (GS-FLC-4.6 as per India Gypsum) in size 600 mm x 600 mm using Gypsum Board tiles /Bison board 8mm thick of size not less than 0.595 M x 0.595 M of 12.5 mm thick as per IS 2095 -1992 fixing to Gyp steel precoated GI wall angle of size 25 mm x 25 mm x of 0.70 mm thick along the perimeter of ceiling screw fixed to brick work/ partition at 610 mm c/c and suspending the frame work using precoated GI Tee section (24 mm x 38 mm x 0.7 mm) from soffit at 1220 mm c/c fixed with GI Soffit Cleat, rawl plugs and steel expansion fasteners & connecting clip to the GI T section with 4 mm dia GI Rod with galvanised spring steel level clip of PVC unversal holding clips system at 1200 mm c/c and fixing the 12.5 mm / 9.5 mm Gypboard Sheet tiles of size 595 mm x 595 mm or 595 mm x 1195 mm and finishing two coats of drywall topcoat complete for finished item of work as per India Gypsum Ltd specification including Overheads & Contractors profit complete for finished item of work in all floors. With cement bounded particle board (Bison panel)/'V' nex + (FCB) or its equivalent

AS PER TENDER DOCUMENT;Supplying and fixing Gyp Board Fine Line Grid false ceiling (GS-FLC-4.6 as per India Gypsum) in size 600 mm x 600 mm using Gypsum Board tiles /Bison board 8mm thick of size not less than 0.595 M x 0.595 M of 12.5 mm thick as per IS 2095 -1992 fixing to Gyp steel precoated GI wall angle of size 25 mm x 25 mm x of 0.70 mm thick along the perimeter of ceiling screw fixed to brick work/ partition at 610 mm c/c and suspending the frame work using precoated GI Tee section (24 mm x 38 mm x 0.7 mm) from soffit at 1220 mm c/c fixed with GI Soffit Cleat, rawl plugs and steel expansion fasteners & connecting clip to the GI T section with 4 mm dia GI Rod with galvanised spring steel level clip of PVC unversal holding clips system at 1200 mm c/c and fixing the 12.5 mm / 9.5 mm Gypboard Sheet tiles of size 595 mm x 595 mm or 595 mm x 1195 mm and finishing two coats of drywall topcoat complete for finished item of work as per India Gypsum Ltd specification including Overheads & Contractors profit complete for finished item of work in all floors.

AS PER TENDER DOCUMENT;Painting to iron/wooden works with 2 coats of ready mixed Synthetic Enamel paints in all shades Grade - I having VOC (Volatile Organic Compound) content less than 50 grams/ literof approved brand and shade over 1 coat of Red Oxide Primer Paint for iron works of Grade -1 of approved brand to give an even shade after thoroughly cleaning and sand papering the surface to remove all dirt and remains , including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. including overheads & contractors profit complete for finished item of work for:-Painting to Iron work - Synthetic enamel paint to wood/Iron Work - 2 coats + 1 coat primer

AS PER TENDER DOCUMENT;Painting to new internal walls with 2 coats of Acrylic emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and shade over a base coat of approved water based Cement Primer of Interior Grade- 1 making 3 coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete and cost of overheads & contractors profit for finished item of work as per SS 912.

AS PER TENDER DOCUMENT;Providing and applying wall putty of White Cement or Polymer or Cement based of average 2 to 3 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, Sand the surface, clean & wipe off loose dust, applying putty/ texture paint filler by putty knife / muslin pad, air dry for 2 - 3 hrs for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc.. including overheads & contractors profit complete for finished item of work for External walls for:-EXternal Colouring - Providing Putty to External walls including scaffolding charges