Telangana State Education Women And Infrastructure Development Corporation Tender

Building work;Supply, delivery and assembling at site Slotted Angle Racks of size 1800x900 x 450mm. The Panels shall be of size 900x450mm. Each Panel shall withstand a load of 100 kg/sqmt UDL. The Angles of size 40x40x2mm shall be in a single piece of length 6', without joints and shall confirm to IS: 5986 (ST 42). Open racks with Side straps on two sides(Left and Right), 150mm heigh. The Panels shall be made up of mild steel sheets, not less than 0.8 mm thick and shall confim to IS 513 D. Epoxy Polyester powder coating of BS Grey colour and shade shall be applied to all components with an average dry film thickness of not less than 35 microns.The total cost of Unit shall include cost of all materials, manufacture, transportation to site, assembling at site including loading, unloading and assembling charges at different floor levels of the building, etc.complete for finished item of work. The item shall carry a warranty period of 3 Years ( 36 months) from the date of supply.

Building work;Supply, delivery and assembling at site Almariahs (Plain model Storewell) of size: 1980x900x450 mm, as shown in the drawing with the following specifications: Store well shall be 4 nos. Fixed shelves of inside shelves size 878 x 420 top bottom LH and RH side and back all parts CR sheet 1 mm thickness with mounting. Die cast recess type handle with 3-way locking mechanism should be provided with levelers. Mild steel as raw material should be used, cold rolled close annealed steel used for thickess 0.6 to 1.2 mm range as per IS ? 513 1994( reaffirmed in 1998). Grade ?D? or ?DD? quality. Chemical composition, tensile properties, bend rest, surface, flatness, hardness as per IS-513 1994. Hot rolled steel used for thickness 2.0 to 3.15mm range as per IS-1079 1994 ?D?quality or IS-10748 1995 Grade-II. Chemical composition, tensile properties, bend rest, surface flaws, roll mark, dent & lines etc. Painting shall be epoxy powder coated paint 55 microns. The total cost of unit shall include cost of all materials, manufacture, transportation to site, assembling at site including loading, unloading and assembling charges at different floor levels of the building, etc., complete for finished item of work. The item shall carry a warranty period of 3 Years (36 months) from the date of supply

Building work;Supply, delivery and assembling at site Staff/Office Table with the following specifications: The over all dimension should be 1200 mm x 590 mm x 750 mm. The table top should be 18mm thick with Pre-Laminated Board (PLB), of approved quality and shade, Grade II Type II conforming to IS:12823. The edges should be sealed with 2mm thick hot preessesd PVC beading. The understructure should be top frame C section 40 x 40 mm 1 mm thickness supported alround tubular frame of CR Round tube of 25.4 mm , 1.2mm thick confirming to IS 513. The tubular frame should be made of CR Round Tube of Dia 25.4mm, 1.2mm thick. For storage, the Table should have 3 drawer unit the overall dimention 350 (w)x 430(H)x 560(D) mm in which the shell and drawer tray shall be 0.5 mm thick CRCA MS, drawer front of 0.8 mm thick CRCA MS sheet, provided with 6 Lever Cam Lock and in built plastic handles. Steel should undergo pre treatment process viz, degreasing, pickling, phosphating etc for rust resistance and durability as per IS std 3618 1996.Epoxy polyster powder coating as per IS101. The total cost of Unit shall include cost of all materials, manufacture, transportation to site assembling at site including loading, unloading and assembling charges at different floor levels of the building,etc.complete for finished item of work. The item shall carry a warranty period of 3 Years ( 36 months) from the date of supply.