Roads And Buildings Department Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Roads And Buildings Department Tender
Civil And Construction
Road Construction
Opening Date19 Aug 2023
Closing Date25 Aug 2023
Tender Amount₹ 4,19,258
Costs
EMD
Refer DocumentsDocument Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
449984Bid Award Id
ViewTender No
DB/HD/04/2023-24/01, Dt: 14.08.2023Tender Authority
Roads And Buildings Department ViewPurchaser Address
-Website
http://http://www.rnbgujarat.org/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Providing Road safety Interventions;Supplying & fixing of Molded Shanks Raised Pavement Markers made of plastic body moulded from HIPS (HI-impact polysterene) or ABS or ASA(Acrylic strene Acrylonirite) and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall suppport a load of 16000 Kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No. RW/NH/33023/10-97-DO III, Dt: 11.06.1997. The height, width and length shall not exceed 50mm, 100mm and with minimum reflective area of 13 SqCm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks.(of diameter not less than 19 +/- 2 mm and height not less than 30 +/- 2mm) from the body is to be a minimum value of 700 Kgs. fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the Engineer-in-Charge
48
399
19152
... More
Providing Road safety Interventions;Providing Rumble Strips in 6 transverse bar with Hot Applied Thermo-plastic compound with 5mm/7.5mm/15mm thick in multiple layers of 2.5mm thick each and 200mm/300mm width including reflectorising glass beads @ 250gms per sqm for top layer on Bituminous surface and top layer thickness of 2.5mm is exclusive of surface applied glass beads as per IRC : 35, the material should be of BERGER Company/ BERGER Equivalent/ Equivalent brand and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference The applied panel 7/8 number must be submitted for checking up the white index in the department lab In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS 3262, Part-1, 1989 and should pass at the range of 'O' degree centigrade to '-10' degree centigrade D) Adhesion : Strong E) Softening point: 102 degree centigrade F) Dried film finish : Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1981 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-2015. The finished surface to be level, uniform and free from streaks and holes etc, complete for finished item of work (with all lifts and leads)
21
4177
87717
... More
Providing Road safety Interventions;Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqmarea, thicknessof 2.5mm is exclusive of surface applied glass bead as per MORTH Section 803.4 and IRC: 35-2015, the material should satisfy the requirements as per MORTH specifications 803.4 and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied productsat site against the approved panel. In case of anymajor deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0' degree centigrade to '-10' degree centigrade D) Adhesion:StrongE)Softeningpoint:102 degreecentigrade F)Dried filmfinish: Smoothanduniform G)Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-2015 and MORTH Section 803.4
15
728
10920
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements