Roads And Buildings Department Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Costs
EMD
₹ 15,63,100Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Formation Of New Four Lane Cc Road From Yadadri Thermal Power Station To Narketpally - Addanki - Medarmetla Road (state Highway-2) Bypassing Tallaverappagudem
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
567559Tender No
CE(R&B) SR & CRN NIT No. 1606-13/DCE(R)/EE-R/DEE-III/AEE-V/2024-25/NLG/1, Dt. 07.01.2025Tender Authority
Roads And Buildings Department ViewPurchaser Address
-Website
http://http://www.rnbgujarat.org/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Road work;Filling in between Reinforced Soil walls with Selected soil meeting approved design parameters in layers (Angle of internal friction not less than 35 deg.) including all leads & lifts, depositing the selected earth between walls, spreading, sectioning, grading and consolidtion with 8 to 10 Tonnes vibratory road Roller @ OMC and with plate compactor/small vibrator for 1.5 m width from facia to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P and seigniorage charges, complete for finished item of work as per MoRT&H specification 305 &2200 (5th Rivision) (Payment will be made based on level for finished item of work) as per approved drawing and as per the directions of the Engineer charge. using selected material (granular) for Railway portion (obligatory) ROB at 1+400
8939.54
452
4040672
... More
Road work;Supplying, fabrication, assembling, riveting, welding where ever required with contractors rivet material, Weld materilas, bolts, sservice bolts rerection and launching of steel Girders as per RDSO Dwg.No.-RDSO/B-11758R with contractors own mild steel confirming to IS2062-1992.All structural steel shall confirm to Grade E-350 (B0) confirming Fe 490B/490 specification except for Rolled sections(Angles, Channels,I -sections).For Rolled section grade "A" Steel may be used and rivets, nuts and Bolts, welding etc, including Contractors own material, Fabrication machinery, Templates, Fixures, Equipments, Tools and Plants approved quality paint, Transportation skilled/Unskilled labours, excise duty, Octroi, sales tax and other taxes, all lead, lift etc. complete.The rates are inclusive of transportation of Fabricated Girder parts to site by contractors own means at his own cost.The rate shall also be inclusive of Cold Straightening of deormed and bent Girder parts before their assembling and other ancillary steel structures where ever necessary for proper level and Alignment. The rate shall be inclusive of Supply, Erection and dismantling of staging and scaffolding and other temporary arrangemnetswhere ever required for the purpose of assembly, erection and Launching of Girders.the Launching has to be done as per scheme supplied by the contractor and approved by Railway with the help of contractor's Road cranes of suitable capacity /Launching nose etc.as approved by Railway during traffic block.The contractor has to bring all the materials after doing primming coat i.e one coat of etch primer( as per IS:5666)one coat of Zinc chrome primer(as per IS:104) to the site.After transportation, assembling and erection at site two coats of finishing coat with aluminium paint as per IS:2339 to be applied after touching of the primming coat if damaged in transit except the floors system which will be metallized.(Painting specification is given in the special conditions.The payment of the Painting ,primming and metatizing will be made as per relevant Items of USSOR 20-10 as per the R.D.S.O./B-11758/R for Railway portion (obligatory) ROB at 1+400
434
184014
79862076
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Substructure for Railway portion (obligatory) ROB at 1+400
166.2
82946
13785625
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Pile Cap Reinforcement for Railway portion (obligatory) ROB at 1+400
22.6
82566
1865992
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Pile Reinforcement for Railway portion (obligatory) ROB at 1+400
30.54
82566
2521566
... More
Road work;Providing weep holes in plain / reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V : 20H towards drawing face, complete as per drawing and technical specifications of MORTH 5th Revison and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
250.15
444
111067
... More
Road work;Providing and laying of filter media behind walls of abutment, retaining wall etc. with granular materials / stone crushed aggregates satisfying the requirements laid down in MoRTH to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
434.73
3808
1655452
... More
Road work;Providing and fixing PVC Pipe 100 mm downtake runner pipes from drainage spout outlet including all accessories complete as per drawings and technical specifications and as directed by the engineer incharge for Railway portion (obligatory) ROB at 1+400
517.5
190
98325
... More
Road work;Providing and fixing of drainage spouts along with drain pipes complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
60
1428
85680
... More
Road work;Providing and laying of strip seal expansion joint catering to maximum horizontal movement up to 40mm, complete as per approved drawing and standard specifications to be installed by manufacturer/supplier or their authorized representative ensuring compliances to the manufacturer's instructions for installations for Railway portion (obligatory) ROB at 1+400
108
7136
770688
... More
Road work;Providing RCC M20 parapet (15 cm x 60 cm) with cast in situ panels as per the drawings including reinforcement, scaffolding, formwork, compacting, finishing, and curing etc. complete for Railway portion (obligatory) ROB at 1+400
175.48
745
130733
... More
Road work;Providing and constructing footpath / paved separator including precast tiles of 25mm thick, preparation of base, drain pipes all complete as per drawing and technical specifications for Railway portion (obligatory) ROB at 1+400
237
1354
320898
... More
Road work;Providing and constructing RCC M40 crash barrier including centering, and shuttering etc. all complete as per technical specificationsas per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
350.96
3010
1056390
... More
Road work;Providing & laying concrete in approach slab including shuttering and reinforcement complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M30 for Railway portion (obligatory) ROB at 1+400
56.7
7767
440389
... More
Road work;Providing & laying concrete in approach slab including shuttering and reinforcement complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - PCC M15 for Railway portion (obligatory) ROB at 1+400
28.35
7138
202362
... More
Road work;Providing and laying 25 mm thick mastic asphalt with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated finegrained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces is not less than 100 deg, protruding 1 mm to 4 mm over mastic surface, complete as per technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
1659
805
1335495
... More
Road work;Providing and laying bituminous wearing coat comprising 40 mm thickness using crushed aggregates of grading-I, premixed with bituminous binder and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction all complete as per technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
66.36
12751
846156
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. Guided bearings- (250 Tonnes capacity) for Railway portion (obligatory) ROB at 1+400
8
39804
318432
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. Free bearings- (250 Tonnes capacity) for Railway portion (obligatory) ROB at 1+400
8
39804
318432
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. Fixed bearings- (250 Tonnes capacity) for Railway portion (obligatory) ROB at 1+400
16
39804
636864
... More
Road work;Providing and laying pedestal concrete, seismic restrainer etc. including centering and shuttering but excluding cost of reinforcement, all complete as per drawing and technical specifications and as directed by the engineer incharge. - RCC M35 - 5m-10m for Railway portion (obligatory) ROB at 1+400
5.63
8668
48801
... More
Road work;Providing & laying cap concrete for abt-cap, piercap dirtwall, bracket, corbells, etc. including formwork, machinery and workmanship complete as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M35 - 5m-10m for Railway portion (obligatory) ROB at 1+400
338.51
8668
2934205
... More
Road work;Providing & laying substructure concrete for piers, abutments, columns, shafts portal, stems, counterforts etc. including formwork, machinery and workmanship complete as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M35 upto 5m for Railway portion (obligatory) ROB at 1+400
279.78
8483
2373374
... More
Road work;Providing & laying foundation concrete for piers, abutments, wing walls, retaining walls etc. including formwork, machinery and workmanship complete as per drawing and technical of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M30 for Railway portion (obligatory) ROB at 1+400
332.43
7881
2619881
... More
Road work;Providing and laying RCC M35 pilecaps mechanically mixed including centering and shuttering but excluding cost of reinforcement, all complete as per drawing and technical specifications and as directed by the engineer incharge for Railway portion (obligatory) ROB at 1+400
226.01
8145
1840851
... More
Road work;Providing and laying in position RCC M35 bored cast in situ piles excluding cost of reinforcement as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Pile Diameter - 1200mm for Railway portion (obligatory) ROB at 1+400
300
15713
4713900
... More
Road work;Providing steel liner for piles including fabricating and setting out as per detailed approved drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
51.48
109224
5622852
... More
Road work;Providing & laying concrete for retaining strucutres like wing-return, curtain wall, toe wall, head wall etc. including formwork, excluding reinforcement complete as per drawing, technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge.-Foundation - RCC M30 for Railway portion (obligatory) ROB at 1+400
497.94
7881
3924265
... More
Road work;Providing & laying levelling course in PCC M15 for foundations complete as per drawings and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for Railway portion (obligatory) ROB at 1+400
107.35
7138
766264
... More
Road work;Earth work in excavation for foundation of structures as per drawings and technical specifications, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom dewatering including all lifts and leads as per the technical specifications of MORT&H 5th Revison and as directed by the Engineer-In-Charge i) All types of soil, including backfilling up to ground level with approved material as directed by Engineer-in-Charge for Railway portion (obligatory) ROB at 1+400
1671.28
143
238993
... More
Road work;Construction of Pavement Quality Concrete un-reinforced, dowel jointed plain Cement concrete pavement of grade M40 with minimum flexural strength of 4.5 MPa at 28 days over a prepared sub base , as per approved mix design including production, transportation to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip/backup rod as per drawing, dowel bar, tie rod, micro fibers,admixtures as approved, curing compound, finishing to lines and grades etc.complete as per specification and drawings. for approaches to ROB 1+400
4070
8634
35140380
... More
Road work;Construction of Dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per Table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing and as directed by the Engineer-in-Charge for below CC Pavement DLC Concrte for approaches to ROB 1+400
2028
4869
9874332
... More
Road work;Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701MORD. Painting of Crash Barrier+ Kerb for approaches to ROB 1+400
2080
106
220480
... More
Road work;Construction of Granular sub-base by providing Grade VI coarse graded material with a minimum CBR Value of 30, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 MORTH. for approaches to ROB 1+400
2892
3745
10830540
... More
Road work;Construction of subgrade with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303 MORD / 305 MORTH, by using machinery. for approaches to ROB 1+400
6760
532
3596320
... More
Road work;Filling in between Reinforced Soil walls with Selected soil meeting approved design parameters in layers (Angle of internal friction not less than 35 deg.) including all leads & lifts, depositing the selected earth between walls, spreading, sectioning, grading and consolidtion with 8 to 10 Tonnes vibratory road Roller @ OMC and with plate compactor/small vibrator for 1.5 m width from facia to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P and seigniorage charges, complete for finished item of work as per MoRT&H specification 305 & 2200 (5th Rivision) (Payment will be made based on level for finished item of work) as per approved drawing and as per the directions of the Engineer charge. for approaches to ROB 1+400
21658
452
9789416
... More
Road work;Construction of Reinforced soil wall including submission & approval of design and drawings, supply of 20 no of panel moulds, all fixtures and accessories, suplly of material (geostrips,geotextile), supply of required quantity of M35 grade concrete (0.2 cum/sqm) and steel along with binding wire as per approved BBS by the consultants (7 kg/cum) for panel casting, supervision at the site during casting & erection and labour for casting, panel shifting and erection including hydra and incidental works complete as per Drawings, Technical Specifications and as directed by the Engineer-In-Charge - RE walls from 8m to 9m for approaches to ROB 1+400
2286
4390
10035540
... More
Road work;Construction of Reinforced soil wall including submission & approval of design and drawings, supply of 20 no of panel moulds, all fixtures and accessories, suplly of material (geostrips,geotextile), supply of required quantity of M35 grade concrete (0.2 cum/sqm) and steel along with binding wire as per approved BBS by the consultants (7 kg/cum) for panel casting, supervision at the site during casting & erection and labour for casting, panel shifting and erection including hydra and incidental works complete as per Drawings, Technical Specifications and as directed by the Engineer-In-Charge - RE walls from 6m to 8m for approaches to ROB 1+400
1960
3773
7395080
... More
Road work;Construction of Reinforced soil wall including submission & approval of design and drawings, supply of 20 no of panel moulds, all fixtures and accessories, suplly of material (geostrips,geotextile), supply of required quantity of M35 grade concrete (0.2 cum/sqm) and steel along with binding wire as per approved BBS by the consultants (7 kg/cum) for panel casting, supervision at the site during casting & erection and labour for casting, panel shifting and erection including hydra and incidental works complete as per Drawings, Technical Specifications and as directed by the Engineer-In-Charge - RE walls from 4m to 6m for approaches to ROB 1+400
1400
3286
4600400
... More
Road work;Construction of Reinforced soil wall including submission & approval of design and drawings, supply of 20 no of panel moulds, all fixtures and accessories, suplly of material (geostrips,geotextile), supply of required quantity of M35 grade concrete (0.2 cum/sqm) and steel along with binding wire as per approved BBS by the consultants (7 kg/cum) for panel casting, supervision at the site during casting & erection and labour for casting, panel shifting and erection including hydra and incidental works complete as per Drawings, Technical Specifications and as directed by the Engineer-In-Charge - RE walls upto height of 4m for approaches to ROB 1+400
720
2957
2129040
... More
Road work;Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 MORD / 710.14 of IRC, 78 & 2200 MORTH 600mm thk. Filter Media behind RE wall for approaches to ROB 1+400
2184
3411
7449624
... More
Road work;Supplying, fitting, and placing Fe 500 HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 MORD / 1600 MORTH, for Bars below 36 mm dia including over laps and wastage, where they are not welded for crash barrier and friction slab @ 160 kg/cum for approaches to ROB 1+400
212
73950
15677400
... More
Road work;Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 MORD / Sections 1500, 1600 & 1700 MORTH RCC M40 in friction slab for approaches to ROB 1+400
946
7310
6915260
... More
Road work;Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 MORD / Sections 1500, 1600 & 1700 MORTH RCC M40 in crash barrier for approaches to ROB 1+400
1026
2696
2766096
... More
Road work;Providing and laying of Reinforced cement concrete M-30 for approach slab including including production from concrete batching plant, vibrating, compacting & finishing, including reinforcement, formwork, cost of all materials, labour, hire charges of machinery, transportation,loading & unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts as per drawings, technical specifications and as per the direction of Engineer-In-Charge for approaches to ROB 1+400
28
6956
194768
... More
Road work;Providing and placing Reinforced cement concrete with grade M20 for RE Wall foundation with crushed stone aggregate of 20 mm nominal size, max free water cement ratio 0.60, including production from concrete batching plant, vibrating, compacting including formwork, cost of all materials, labour, hire charges of machinery, transportation,loading &unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts and as per drawings, technical specifications and the direction of Engineer-In-Charge for approaches to ROB 1+400
126
6742
849492
... More
Road work;Providing and placing plain cement concrete with grade M15 for levelling course with crushed stone aggregate of 40 mm nominal size,minimum cement content 220 kg/cum, max free water cement ratio 0.60, including production from concrete batching plant, vibrating, compacting including formwork, cost of all materials, labour, hire charges of machinery, transportation,loading &unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts and as per drawings, technical specifications and the direction of Engineer-In-Charge for approaches to ROB 1+400
5
6393
31965
... More
Road work;Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification of MORTH - 5% for Hard Rock (Blasting Prohibited) for approaches to ROB 1+400
54.05
902
48753
... More
Road work;Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification of MORTH -95% for Soils (Mechanical Means) for approaches to ROB 1+400
1027.03
128
131460
... More
Road work;Printing of structure number, span arrangement & flow direction of any shade with synthetic enamel paint black or any other approved colour to give an even shade as complete as per technical specifications and as directed by the engineer incharge for ROB at 1+400
4
106
424
... More
Road work;Providing and applying ordinary paints of approved quality on surface of parapets / crash barrier as per drawings and as per the directions of the engineer for ROB at 1+400
757.4
106
80284
... More
Road work;Providing and laying pitching on slopes laid over prepared filter material including boulder apron laid dry in front of toe of embankment complete as per drawing and technical specification for ROB at 1+400
134.04
3606
483348
... More
Road work;Filling in between Reinforced Soil walls with Selected soil meeting approved design parameters in layers (Angle of internal friction not less than 35 deg.) including all leads & lifts, depositing the selected earth between walls, spreading, sectioning, grading and consolidtion with 8 to 10 Tonnes vibratory road Roller @ OMC and with plate compactor/small vibrator for 1.5 m width from facia to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P and seigniorage charges, complete for finished item of work as per MoRT&H specification 305 &2200 (5th Rivision) (Payment will be made based on level for finished item of work) as per approved drawing and as per the directions of the Engineer charge using selected maerial (granular) for ROB at 1+400
8802.72
452
3978829
... More
Road work;Providing and fixing high tensile steel wires / strands including all accessories for stressing, stressing operations and grouting complete as per drawing and technical specifications of as per the technical specifications of MORT&H 5th Revison and as directed by the Engineer-In-Charge for ROB at 1+400
75.67
154631
11700928
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Superstructure for ROB at 1+400
267.38
85530
22869011
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Substructure for ROB at 1+400
244.53
82946
20282785
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Pile Cap Reinforcement for ROB at 1+400
69.35
82566
5725952
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Pile Reinforcement for ROB at 1+400
91.61
82566
7563871
... More
Road work;Providing weep holes in plain / reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V : 20H towards drawing face, complete as per drawing and technical specifications of MORTH 5th Revison and as directed by the Engineer-In-Charge for ROB at 1+400
451.2
444
200333
... More
Road work;Providing and laying of filter media behind walls of abutment, retaining wall etc. with granular materials / stone crushed aggregates satisfying the requirements laid down in MoRTH to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
572.76
3808
2181070
... More
Road work;Providing and fixing PVC Pipe 100 mm downtake runner pipes from drainage spout outlet including all accessories complete as per drawings and technical specifications and as directed by the engineer incharge for ROB at 1+400
439.7
190
83543
... More
Road work;Providing and fixing of drainage spouts along with drain pipes complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
52
1428
74256
... More
Road work;Providing and laying of strip seal expansion joint catering to maximum horizontal movement up to 40mm, complete as per approved drawing and standard specifications to be installed by manufacturer/supplier or their authorized representative ensuring compliances to the manufacturer's instructions for installations for ROB at 1+400
250
7136
1784000
... More
Road work;Providing RCC M20 parapet (15 cm x 60 cm) with cast in situ panels as per the drawings including reinforcement, scaffolding, formwork, compacting, finishing, and curing etc. complete for ROB at 1+400
151.48
745
112853
... More
Road work;Providing and constructing footpath / paved separator including precast tiles of 25mm thick, preparation of base, drain pipes all complete as per drawing and technical specifications for ROB at 1+400
201
1354
272154
... More
Road work;Providing and constructing RCC M40 crash barrier including centering, and shuttering etc. all complete as per technical specificationsas per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
302.96
3010
911910
... More
Road work;Providing & laying concrete in approach slab including shuttering and reinforcement complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - PCC M30 for ROB at 1+400
52.5
7767
407768
... More
Road work;Providing & laying concrete in approach slab including shuttering and reinforcement complete as per drawing and technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - PCC M15 for ROB at 1+400
26.25
7138
187373
... More
Road work;Providing and laying 25 mm thick mastic asphalt with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated finegrained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces is not less than 100 deg, protruding 1 mm to 4 mm over mastic surface, complete as per technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
1273
805
1024765
... More
Road work;Providing and laying bituminous wearing coat comprising 40 mm thickness using crushed aggregates of grading-I, premixed with bituminous binder and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction all complete as per technical specifications as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
50.92
12751
649281
... More
Road work;Providing and laying concrete for cast insitu deck slabs, solid slabs, voided slabs including centering, form-work, scaffolding and curing etc. complete (excluding reinforcement) as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M40 (5m-10m) for ROB at 1+400
675
9841
6642675
... More
Road work;Providing and laying concrete for cast insitu cross girder diaphragms, including centering, form-work, scaffolding and curing etc. complete (excluding reinforcement) as per the technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. - RCC M40(5m-10m) for ROB at 1+400
146.1
9841
1437770
... More
Road work;Providing RCC/PSC Precast I-girders (post-tensioned) including transportation and launching at location (if applicable) in superstructure complete excluding cost of steel reinforcement including shuttering, erection and launching complete as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - PSC M45 (5m-10m) for ROB at 1+400
1126.7
10383
11698526
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. Guided bearings- (250 Tonnes capacity) for ROB at 1+400
8
39804
318432
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. Free bearings- (250 Tonnes capacity) for ROB at 1+400
8
39804
318432
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge. Fixed bearings- (250 Tonnes capacity) for ROB at 1+400
16
39804
636864
... More
Road work;Providing and laying pedestal concrete, seismic restrainer etc. including centering and shuttering but excluding cost of reinforcement, all complete as per drawing and technical specifications and as directed by the engineer incharge. - RCC M35 (5m-10m) for ROB at 1+400 for ROB at 1+400
45.06
8668
390580
... More
Road work;Providing & laying cap concrete for abt-cap, piercap dirtwall, bracket, corbells, etc. including formwork, machinery and workmanship complete as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M35 - 5m-10m for ROB at 1+400
507.26
8668
4396930
... More
Road work;Providing & laying substructure concrete for piers, abutments, columns, shafts portal, stems, counterforts etc. including formwork, machinery and workmanship complete as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M35 upto 5m for ROB at 1+400
765.94
8483
6497469
... More
Road work;Providing & laying foundation concrete for piers, abutments, wing walls, retaining walls etc. including formwork, machinery and workmanship complete as per drawing and technical of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - RCC M30 for ROB at 1+400
332.43
7881
2619881
... More
Road work;Providing and laying RCC M35 pilecaps mechanically mixed including centering and shuttering but excluding cost of reinforcement, all complete as per drawing and technical specifications and as directed by the engineer incharge for ROB at 1+400
693.5
8145
5648558
... More
Road work;Providing and laying in position RCC M35 bored cast in situ piles excluding cost of reinforcement as per drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge - Pile Diameter - 1200mm for ROB at 1+400
900
15713
14141700
... More
Road work;Providing steel liner for piles including fabricating and setting out as per detailed approved drawing and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
154.44
109224
16868555
... More
Road work;Providing & laying concrete for retaining strucutres like wing-return, curtain wall, toe wall, head wall etc. including formwork, excluding reinforcement complete as per drawing, technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge.-Foundation - RCC M30 for ROB at 1+400
497.94
7881
3924265
... More
Road work;Providing & laying levelling course in PCC M15 for foundations complete as per drawings and technical specifications of 5th Revision of MORT&H and as directed by the Engineer-In-Charge for ROB at 1+400
173.82
7138
1240727
... More
Road work;Earth work in excavation for foundation of structures as per drawings and technical specifications, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom dewatering including all lifts and leads as per the technical specifications of MORT&H 5th Revison and as directed by the Engineer-In-Charge i) All types of soil, including backfilling up to ground level with approved material as directed by Engineer-in-Charge for ROB at 1+400
2412.43
143
344977
... More
Road work;Construction of Pavement Quality Concrete un-reinforced, dowel jointed plain Cement concrete pavement of grade M40 with minimum flexural strength of 4.5 MPa at 28 days over a prepared sub base , as per approved mix design including production, transportation to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip/backup rod as per drawing, dowel bar, tie rod, micro fibers,admixtures as approved, curing compound, finishing to lines and grades etc.complete as per specification and drawings for Approaches for HLB at Km 7/900
163
8634
1407342
... More
Road work;Construction of Dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per Table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing and as directed by the Engineer-in-Charge for below CC Pavement DLC Concrete for Approaches for HLB at Km 7/900
78
4869
379782
... More
Road work;Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701MORD. Painting of Crash Barrier+ Kerb for HLB at Km 7/900
160
106
16960
... More
Road work;Construction of Granular sub-base by providing Grade VI coarse graded material with a minimum CBR Value of 30, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 MORTH for Approaches for HLB at Km 7/900
119
3745
445655
... More
Road work;Construction of subgrade with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303 MORD / 305 MORTH, by using machinery for Approaches for HLB at Km 7/900
260
532
138320
... More
Road work;Filling in between Reinforced Soil walls with Selected soil meeting approved design parameters in layers (Angle of internal friction not less than 35 deg.) including all leads & lifts, depositing the selected earth between walls, spreading, sectioning, grading and consolidtion with 8 to 10 Tonnes vibratory road Roller @ OMC and with plate compactor/small vibrator for 1.5 m width from facia to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P and seigniorage charges, complete for finished item of work as per MoRT&H specification 305 &2200 (5th Rivision) (Payment will be made based on level for finished item of work) as per approved drawing and as per the directions of the Engineer charge for Approaches for HLB at Km 7/900
1242
452
561384
... More
Road work;Construction of Reinforced soil wall including submission & approval of design and drawings, supply of 20 no of panel moulds, all fixtures and accessories, suplly of material (geostrips,geotextile), supply of required quantity of M35 grade concrete (0.2 cum/sqm) and steel along with binding wire as per approved BBS by the consultants (7 kg/cum) for panel casting, supervision at the site during casting & erection and labour for casting, panel shifting and erection including hydra and incidental works complete as per Drawings, Technical Specifications and as directed by the Engineer-In-Charge for RE walls upto height of 4m for Approaches for HLB at Km 7/900
434
2957
1283338
... More
Road work;Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 MORD / 710.14 of IRC, 78 & 2200 MORTH for 600mm thick filter media behind RE Wall for Approaches for HLB at Km 7/900
216
3411
736776
... More
Road work;Supplying, fitting, and placing Fe 500 HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 MORD / 1600 MORTH, for Bars below 36 mm dia including over laps and wastage, where they are not welded For Crash Barrier and Friction slab @ 160kg/cum for Approaches for HLB at Km 7/900
15
73950
1109250
... More
Road work;Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 MORD / Sections 1500, 1600 & 1700 MORTH for RCC M40 in Friction Slab Approaches for HLB at Km 7/900
61
7310
445910
... More
Road work;Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 MORD / Sections 1500, 1600 & 1700 MORTH for RCC M40 in Crash Barrier Approaches for HLB at Km 7/900
66
2696
177936
... More
Road work;Providing and laying of Reinforced cement concrete M-30 for approach slab including including production from concrete batching plant, vibrating, compacting & finishing, including reinforcement,formwork, cost of all materials, labour, hire charges of machinery, transportation,loading &unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts as per drawings, technical specifications and as per the direction of Engineer-In-Charge for Approaches for HLB at Km 7/900
14
6956
97384
... More
Road work;Providing and placing Reinforced cement concrete with grade M20 for RE Wall foundation with crushed stone aggregate of 20 mm nominal size, , max free water cement ratio 0.60, including production from concrete batching plant, vibrating, compacting including formwork, cost of all materials, labour, hire charges of machinery, transportation,loading &unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts and as per drawings, technical specifications and the direction of Engineer-In-Charge for Approaches for HLB at Km 7/900
13
6742
87646
... More
Road work;Providing and placing plain cement concrete with grade M15 for levelling course with crushed stone aggregate of 40 mm nominal size,minimum cement content 220 kg/cum, max free water cement ratio 0.60, including production from concrete batching plant, vibrating, compacting including formwork, cost of all materials, labour, hire charges of machinery, transportation,loading &unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts and as per drawings, technical specifications and the direction of Engineer-In-Charge for Approaches for HLB at Km 7/900
7
6393
44751
... More
Road work;Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification of MORTH - 5% for Hard Rock (Blasting Prohibited) for Approaches for HLB at Km 7/900
5.25
902
4736
... More
Road work;Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification of MORTH -95% for Soils (Mechanical Means) for Approaches for HLB at Km 7/900
99.69
128
12760
... More
Road work;Printing of structure number, span arrangement & flow direction of any shade with synthetic enamel paint black or any other approved colour to give an even shade as complete as per technical specifications and as directed by the engineer incharge for HLB at Km 7/900
1
106
106
... More
Road work;Providing and applying ordinary paints of approved quality on surface of parapets / crash barrier as per drawings and as per the directions of the engineer for HLB at Km 7/900
1004.98
106
106528
... More
Road work;Providing and laying pitching on slopes laid over prepared filter material including boulder apron laid dry in front of toe of embankment complete as per drawing and technical specification for HLB at Km 7/900
73.71
3606
265798
... More
Road work;Filling in between Reinforced Soil walls with Selected soil meeting approved design parameters in layers (Angle of internal friction not less than 35 deg.) including all leads & lifts, depositing the selected earth between walls, spreading, sectioning, grading and consolidtion with 8 to 10 Tonnes vibratory road Roller @ OMC and with plate compactor/small vibrator for 1.5 m width from facia to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P and seigniorage charges, complete for finished item of work as per MoRT&H specification 305 &2200 (5th Rivision) (Payment will be made based on level for finished item of work) as per approved drawing and as per the directions of the Engineer charge using selected granular material for HLB at Km 7/900
3760.16
452
1699592
... More
Road work;Providing and fixing high tensile steel wires / strands including all accessories for stressing, stressing operations and grouting complete as per drawing and technical specifications for HLB at Km 7/900
25.02
154631
3868868
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification section and as directed by engineer for Super structure for HLB at Km 7/900
88.12
85530
7536904
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification section and as directed by engineer for Sub structure for HLB at Km 7/900
90.3
82946
7490024
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification section and as directed by engineer for Pile Cap Reinforcement for HLB at Km 7/900
45.99
82566
3797210
... More
Road work;Supplying, fitting and placing HYSD-TMT reinforcement (Fe-500 grade) in foundation, substructure and superstructure complete as per drawing, technical specification section and as directed by engineer for Pile Reinforcement for HLB at Km 7/900
45.8
82566
3781523
... More
Road work;Providing weep holes in plain / reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V : 20H towards drawing face, complete as per drawing and technical specifications section for HLB at Km 7/900
259.61
444
115267
... More
Road work;Providing and laying of filter media behind walls of abutment, retaining wall etc. with granular materials / stone crushed aggregates satisfying the requirements laid down in MoRTH to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification for HLB at Km 7/900
312.61
3808
1190419
... More
Road work;Providing and fixing PVC Pipe 100 mm downtake runner pipes from drainage spout outlet including all accessories complete as per drawings and technical specifications and as directed by the engineer incharge for HLB at Km 7/900
595.78
190
113198
... More
Road work;Providing and fixing of drainage spouts along with drain pipes complete as per drawing and technical specifications and as directed by the engineer for HLB at Km 7/900
19
1428
27132
... More
Road work;Providing and laying of strip seal expansion joint catering to maximum horizontal movement up to 40mm, complete as per approved drawing and standard specifications to be installed by manufacturer/supplier or their authorized representative ensuring compliances to the manufacturer's instructions for installations for HLB at Km 7/900
50
7136
356800
... More
Road work;Providing RCC M20 parapet (15 cm x 60 cm) with cast in situ panels as per the drawings including reinforcement, scaffolding, formwork, compacting, finishing, and curing etc. complete for HLB at Km 7/900
201
745
149745
... More
Road work;Providing and constructing footpath / paved separator including precast tiles of 25mm thick, preparation of base, drain pipes all complete as per drawing and technical specifications for HLB at Km 7/900
145.5
1354
197007
... More
Road work;Providing and constructing RCC M40 crash barrier including centering & shuttering etc. all complete as per technical specifications for HLB at Km 7/900
401.99
3010
1209990
... More
Road work;Providing & laying concrete in approach slab including shuttering and reinforcement complete as per drawing and technical specification RCC M30 for HLB at Km 7/900
26.25
7767
203884
... More
Road work;Providing & laying concrete in approach slab including shuttering and reinforcement complete as per drawing and technical specification PCC M15 for HLB at Km 7/900
13.13
7138
93722
... More
Road work;Providing and laying 25 mm thick mastic asphalt with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated finegrained hard stone chipping of 13.2 mm nominal size at the rate of 0.005 cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces is not less than 100 deg, protruding 1 mm to 4 mm over mastic surface, complete as per technical specifications and as directed by the engineer incharge for HLB at Km 7/900
921.5
805
741808
... More
Road work;Providing and laying bituminous wearing coat comprising 40 mm thickness using crushed aggregates of grading-I, premixed with bituminous binder and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction all complete as per technical specification and as directed by the engineer incharge for HLB at Km 7/900
36.86
12751
470002
... More
Road work;Providing and laying concrete for cast insitu deck slabs, solid slabs, voided slabs including centering, form-work, scaffolding and curing etc. complete (excluding reinforcement) RCC M40 for HLB at Km 7/900
253.13
9841
2491052
... More
Road work;Providing and laying concrete for cast insitu cross girder diaphragms, including centering, form-work, scaffolding and curing etc. complete (excluding reinforcement). RCC M40 for HLB at Km 7/900
40.4
9841
397576
... More
Road work;Providing RCC/PSC Precast I-girders (post-tensioned) including transportation and launching at location (if applicable) in superstructure complete excluding cost of steel reinforcement including shuttering, erection and launching complete as per drawing and technical specification PSC M45 for HLB at Km 7/900
342.61
10383
3557320
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications as directed by the engineer incharge for Guided Bearings (250 Tonnes Capacity) for HLB at Km 7/900
6
39804
238824
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications as directed by the engineer incharge for Free Bearings (250 Tonnes Capacity) for HLB at Km 7/900
6
39804
238824
... More
Road work;Supplying, fitting and fixing in position true to line and level POT-PTFEE bearing (free, sliding & fixed) consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cyliners, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be cast steel / fabricated structural steel, metal and elastomer elements conforming to IRC-83 (Part-II & III) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and technical / manufacturer's specifications as directed by the engineer incharge for Fixed Bearings (250 Tonnes capacity) for HLB at Km 7/900
12
39804
477648
... More
Road work;Providing and laying pedestal concrete, seismic restrainer etc. including centering and shuttering but excluding cost of reinforcement, all complete as per drawing and technical specifications and as directed by the engineer incharge RCC M35 for HLB at Km 7/900
8.45
8668
73245
... More
Road work;Providing & laying cap concrete for abt-cap, piercap dirtwall, bracket, corbells, etc. including formwork, machinery and workmanship complete as per drawing and technical specification RCC M35 (5m - 10m) for HLB at Km 7/900
173.42
8668
1503205
... More
Road work;Providing & laying substructure RCC M35 concrete for piers, abutments, columns, shafts portal, stems, counterforts etc. including formwork, machinery and workmanship complete as per drawing and technical specification for HLB at Km 7/900
303.97
8483
2578578
... More
Road work;Providing & laying foundation RCC M30 concrete for piers, abutments, wing walls, retaining walls etc. including formwork, machinery and workmanship complete as per drawing and technical specification for HLB at Km 7/900
221.71
7881
1747297
... More
Road work;Providing and laying RCC M35 pilecaps mechanically mixed including centering and shuttering but excluding cost of reinforcement, all complete as per drawing and technical specifications and as directed by the engineer incharge for HLB at Km 7/900
459.9
8145
3745886
... More
Road work;Providing and laying in position RCC M35 bored cast in situ piles excluding cost of reinforcement as per drawing and technical specifications and as directed by the engineer incharge pile diameter 1200mm for HLB at Km 7/900
450
15713
7070850
... More
Road work;Providing steel liner for piles including fabricating and setting out as per detailed approved drawing and technical specifications of MORT&H 5th Revison & as directed by Engineer-In-Charge for HLB at Km 7/900
77.22
109224
8434277
... More
Road work;Providing & laying RCC M30 concrete for retaining strucutres like wing-return, curtain wall, toe wall, head wall etc. including formwork, excluding reinforcement complete as per drawing, technical specification for HLB at Km 7/900
247.06
7881
1947080
... More
Road work;Providing & laying levelling course in PCC M15 for foundations complete as per drawings and technical specification for HLB at Km 7/900
116.3
7138
830149
... More
Road work;Earth work in excavation for foundation of structures as per drawings and technical specifications, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom dewatering including all lifts and leads i) All types of soil, including backfilling up to ground level with approved material as directed by Engineer-in-Charge for HLB at Km 7/900
1604.66
143
229466
... More
Road work;Providing,Supply and fixing of heavy duty type single compression brass cable glands duly nickel plated complete with brass checknut, outer sheath sealing rubber ring and washers suitable for 25 Sqmm to 50.0 Sq.mm 3.5 Core XLPE insulated armoured cable, including all labour charges and miscellaneous items etc complete. Makes: SMI / Commet / Dowels. (ELEC-4.3.1.c) for Street lighting
266
396
105336
... More
Road work;Earthwork excavation in soils upto SDR by Manual means including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections etc., complete including for finished item of work for trench cutting as per MoRT&H specification 301(5th Revision) and as directed by the Engineer-in-Charge for Street lighting
16.2
427
6917
... More
Road work;Providing and placing plain cement concrete for electrical poles levelling course with grade M15 with crushed stone aggregate of 20 mm nominal size,minimum cement content 220 kg/cum, max free water cement ratio 0.60, including production from concrete mixer, vibrating, compacting including formwork, cost of all materials, labour, hire charges of machinery, transportation,loading &unloading, stacking charges, curing, dewatering including pumping etc. complete including all leads & lifts and as per drawings, technical specifications and the direction of Engineer-In-Charge for Street lighting
4.05
7203
29172
... More
Road work;Supply & Laying of 2.5 Sqmm (36/0.3mm) 4 Core PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 including all transportation charges etc. complete and as directed by the the Engineer-In-Charge. Makes :Finolex / RR kabel / Havells / Polycab / RPG / KEI / Gloster / V-Guard / Finecab / SPM / Gemini / Unistar / Windsor / Payal / Fortune Arrt / Avocab / Pawancab / Nakoda / HPL / Sudhakar / Bonton / Ollvin. (ELEC-1.5.6.t) for Street lighting
132
205
27060
... More
Road work;Supply and transportation of 200 W +/-10% (>=20000 Lumens) LED Flood light Luminaire made of pressuredie cast aluminum housing with powdercoated, having toughened glass cover, Suitable lens on LEDs, IP 66 (Silicongasket ensures Optical & Electricalcompartments are IP 66 )protected, wideoperating voltage range , P.F > 0.90,System having efficacy >110lumens/watt, with Ingress protectionIP66, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desiredby the department and as per IS, CRI>70,Inbuilt Electrical protections like Overvoltage, short circuit, Over load, OpenCircuit, Miswiring, etc complete with BIScertification with 5 years warranty. The contractor has to furnish themanufacturer warranty letter, LM 79 and LM 80 certificates. LUMINAIRE MAKE : PHILIPS / OSRAM / GEVenture / CROMPTON / BAJAJ / Surya /Wipro / Jaquar / Eveready / Halonix /Keselec / HAVELLS / POLYCAB / SURYA /SYSKA./ Capart / Fortune Arrt / FIEM /Arraystorm / GM / Goldmedal / Panasonic/ Silicon / Leksa / Orient / HPLLED MAKE : PHILIPS LUMILEDS / CREE /NICHIA / OSRAM / SAMSUNG / LG LEDs. (ELEC-3.5.4.e) for Street lighting
21
17110
359310
... More
Road work;Earth work exacavation with a approximate quantity of 6.0 Cum for errection of 16 Mtrs high mast and refilling with a quantity of 0.65 Cum of PCC 1:4:8, 2.60 Cum M 20 grade concrete and (110 Kgs) reinforced steel of 12mm / 10mm / 8mm, Soil bearing capacity of 10 T/Sqm, Anchor plate with cost and conveyance of all above materials including labour charges for errection of High Mast and Carraige etc complete including soil testing. etc. complete and as directed by the the Engineer-In-Charge.ELEC-8.7.2 for Street lighting
3
46980
140940
... More
Road work;Fabrication, transportation and supply of 16 Mtrs Polygon High Mast with two sections of Bottom 4mm thick and Top section with 3mm thick with GLS type aviation lamp of Bottom 360mm and Top 150mm dia with BSEN - 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate, having a base plate of size 560mm dia 25mm thick with its accessories. Mast shall be in 2 sections and should be hot dip galvanized and suiatble for wind velocity of 180 KMPH as per IS 875 part 3 including head frame, 2 point suspension system with steel rope 6mm dia (7/19) construction double drum winch / power tool, and necessary cable trailer connections and single speed motor with M 24 x 800 mm foundation bolts of required quantity, suitable for 6 Flood lights, with GLS type aviation twin lamp Makes : BAJAJ / VALMONT / TRANSRAIL / SKIPPER / UTKARSH / LAASMA / CONSOUL ELEC-8.5.2 for Street lighting
3
172860
518580
... More
Road work;Providing,supply, Installation, testing and commissioning of alluminium lugs confirming to I.S specifications for cable upto 25 Sq.mm including nuts and bolts with connections. Including all fixtures & fittings complete technical specification etc. complete and as directed by the the Engineer-In-Charge. Make:Comet ,Jainson (ELEC - 4.4.2.b) for Street lighting
72
62
4464
... More
Road work;Providing,Supply and fixing of heavy duty type single compression brass cable glands duly nickel plated complete with brass checknut, outer sheath sealing rubber ring and washers suitable for 25 Sqmm to 50.0 Sq.mm 3.5 Core XLPE insulated armoured cable, including all labour charges and miscellaneous items etc complete. Makes: SMI / Commet / Dowels. (ELEC-4.3.1.c) for Street lighting
18
396
7128
... More
Road work;Supply and Laying ,testing commisioning of 25 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specificationconfirming to IS:7098 (Part - I). Makes : Torrent / Universal / Unicab / Polycab / Havells /Gloster / KEI Including all fixtures & fittings etc. complete and as directed by the the Engineer-In-Charge. (ELEC-4.1.1.g) for Street lighting
900
409
368100
... More
Road work;Supply and fixing of Automatic Street Light Control System with Optical Sensor, Low volatage / High voltage trip and reset, operating voltage 380 - 450 V AC, 50 HZ with suitable SMC enclousure of IP 54 protection, MCBs of Legrand / Schneider / L&T / Siemens of 10KA C/D curve and Contactor suitable to control the load of 8 kW Three phase load with necessary clamping arrangementsetc. complete and as directed by the the Engineer-In-Charge. Makes : Swadeep Nature Switch / Light Mate / L&T / Siemens / Bajaj (ELEC-3.2.2.b) for Street lighting
9
17042
153378
... More
Road work;Supply, Transportation and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete, including Supply and fixing of Legrand / Schnieder make 63A, 4 Pole MCB as incomer, 9 Nos 6-32A SP MCBs as out goings, indication lamps, din channel, 6 Sqmm 3 core copper cable for invidual light control, connectors, bus bars, shroudings, gland plates and provision for 3 phase energy meter etc., complete for finished item of work and suitable wiring provision for connecting the nature switch Complete. (ELEC-8.6.2.b) for Street lighting
9
30767
276903
... More
Road work;Providing Independent Earthing for Important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr. long connectedwith reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II) etc. complete and as directed by the the Engineer-In-Charge. (ELEC-8.16.7) for Street lighting
18
6635
119430
... More
Road work;Supply & laying of 25 X 3mm GI Strip including cost of all accessories including connections and labour chargesetc. complete and as directed by the the Engineer-In-Charge.(ELEC-10.3.6) for Street lighting
180
110
19800
... More
Road work;Supplying and laying 8 SWG G.l. wire for earthing including connection /termination with Gl thimble etc. complete and as directed by the the Engineer-In-Charge. (ELEC-10.3.6) for Street lighting
100
30
3000
... More
Road work;Supply and Transportation of Outer dia 63mm and Inner dia 51mm double walled corrugated HDPE duct made as per specification BSEN - 500 86/IS 14930 Part-II with all accessories like couplers, bends, end caps, Ts etc., complete technical specification as per instructions of EIC . Makes: DURA LINE (Dura Guard) / Bajaj / Gamson / Ultra Plus (ELEC-4.9.1.b) for Street lighting
4890
153
748170
... More
Road work;Supply and Fixing of heavy duty type single compression brass cable glands duly nickel plated complete with brass checknut, outer sheath sealing rubber ring and washers suitable for 10 Sqmm 4 Core XLPE insulated armoured cable etc. complete and as directed by the the Engineer-In-Charge. Makes: SMI / Commet / Dowels. (ELEC-4.3.1.b) for Street lighting
9
317
2853
... More
Road work;Supply, Laying and testing of 10 Sqmm 4 Core XLPE insulated, 1100V grade armoured alluminium cable as per specificationconfirming to IS:7098 (Part - I). Makes : Torrent / Universal / Unicab / Polycab / Havells /Gloster / KEI Including all fixtures & fittings etc. complete and as directed by the the Engineer-In-Charge. ELEC-4.1.1(e) for Street lighting
1100
284
312400
... More
Road work;Supply & Laying of 2.5 Sqmm (36/0.3mm) 4 Core PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 including all transportation charges etc. complete and as directed by the the Engineer-In-Charge. Makes :Finolex / RR kabel / Havells / Polycab / RPG / KEI / Gloster / V-Guard / Finecab / SPM / Gemini / Unistar / Windsor / Payal / Fortune Arrt / Avocab / Pawancab / Nakoda / HPL / Sudhakar / Bonton / Ollvin. (ELEC-1.5.6.t) for Street lighting
3990
205
817950
... More
Road work;Supply & Laying of 2.5 Sqmm (36/0.3mm) 3 Core PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 including all transportation charges etc. complete and as directed by the the Engineer-In-Charge. Makes :Finolex / RR kabel / Havells / Polycab / RPG / KEI / Gloster / V-Guard / Finecab / SPM / Gemini / Unistar / Windsor / Payal / Fortune Arrt / Avocab / Pawancab / Nakoda / HPL / Sudhakar / Bonton / Ollvin. (ELEC-1.5.6.n) for Street lighting
3724
182
677768
... More
Road work;Providing,supply, Installation, testing and commissioning of 150 Watts LED Street light Body made of high gradepressure die ? cast Aluminium alloy withcorrosion resistant powder coat, having protective toughened glass cover,Suitable lens on LEDs, Less Glare, IP 66(Silicon gasket ensures Optical &Electrical compartments are IP 66) protected, wide operating voltage range, P.F > 0.90, System having efficacy >110 lumens/watt, with Ingress protection IP66, Potted driver, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desired by the department and as per IS, CRI>70, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc complete with BIS certification with 5 years warranty. The contractor has to furnish the manufacturer warranty letter, LM 79 and LM 80 certificates.complete and as directed by the the Engineer-In-Charge.LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG LEDs. LUMINAIRE MAKE : PHILIPS / OSRAM / GE Venture /CROMPTON / BAJAJ / VIN / Wipro / Jaquar / Keselec / HAVELLS /HPL / SURYA / SYSKA. LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM /SAMSUNG / LG LEDs. (ELEC-3.5.1.j) for Street lighting
266
11765
3129490
... More
Road work;Fabrication, Transportation, supply & Fixing of 1.5 Mtr sword type or any decorative Double arm bracket with dooms complete with all accessories with MS galvanized 50mm dia Pipe. Complete As per Instruction of Engineer in Charge. Makes: BAJAJ / VALMONT / TRANSRAIL /SKIPPER / UTKARSH / LAASMA / CONSOUL (ELEC-8.4.2.d) for Street lighting
133
6703
891499
... More
Road work;Foundation and erection charges with special T&P, for 9.00Mtrs / 10Mtrs long Octagonal / Conical pole duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.60Mtrx0.60Mtrsx1.40 Mtr size M20 cc work vibrated concreting mixing with necessary steel (15kgs) reinforcement as directed by the field engineers during execution including centering, decentering, water curing as required, soil exacavation, back filling, muffing removal and coil earthing including all labour charges and cost and conveyance of materials etc. complete. and as directed by the the Engineer-In-Charge. (ELEC-8.11.3) for Street lighting
133
9998
1329734
... More
Road work;Fabrication, Transportation and supply of hot-dip galvanized Octogonal Pole with BSEN - 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangement, including chain for anti theft mechanism, supply of suitable boards with bakelite sheet, din channel for MCB's as per IS specification suitable to withstand the wind speed of 180 KMPH for 10 Mtrs height Pole having dimensions Bottom 175mm, Top 70mm with 3mm thick, base plate 275 x 275 x16mm and 4 Nos of M24 x 750mm long 'J' bolts along with template or equivalent. etc. complete and as directed by the the Engineer-In-Charge. Makes: BAJAJ / VALMONT / TRANSRAIL / SKIPPER / UTKARSH / LAASMA / CONSOUL ( ELEC-8.3.1.c ) for Street lighting
133
24052
3198916
... More
Road work;Painting 2 coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surface as per Tech Specification 800 MORTH (5th revision) and as directed by the Engineer in charge etc., complete for finished item of work.
7525
106
797650
... More
Road work;Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc - Boundary pillar
880
1218
1071840
... More
Road work;Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc - Hectometer stone
2
855
1710
... More
Road work;Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc - Ordinary Kilometer stone
22
3037
66814
... More
Road work;Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc - 5th Kilometer stone
4
5040
20160
... More
Road work;Supplying & Fixing of Molded Shanks Raised Pavement Markers made of plastic body moulded from HIPS(HI- impact polysterene ) or ABS or ASA (Acrylic strene Acrylonitrite) and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No.RW/NH/33023/10-97-DOIII Dt.11-06-1997.The height, width and length shall not exceed 50mm,100mm and 100mm and with minimum refelective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree.The Strength of detachment of the integrated cylindrical shanks (of diameter not less than 19 +/- 2 mm and height not less than 30 +/- 2 mm ) from the body is to be a minimum value of 700 Kgs.Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturers recommendation and complete as per the instructions by the Engineer-in-Charge.
3341
399
1333059
... More
Road work;Providing and fixing Mandatory / Regulatory sign boards size 600 mm circle made out of Type ? XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67 for full background of White colour and letters/logos done by screen printing in Black colour, boarders by screen printing in Red colour and fixed over 3MM Alluminium Composite Material sheet having minimum 0.30mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer -in-Charge.
44
6915
304260
... More
Road work;Providing and fixing Village name board size 600x800 mm made out of Type ? XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of Green Colour & White Letters and fixed over 3MM Alluminium Composite Material sheet having minimum 0.30mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paintBlackandWhite colourwith bandsof 30cmof height. The signpostshall befirmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer ?in-Charge.
44
9629
423676
... More
Road work;Providing and fixing Cautionary / Warning sign boards size 900 mm equilateral triangle made out of Type ? XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of White colour and letters/logos done by screen printing in Black colour, boarders by screen printing in Red colour and fixed over 4MM Aluminium Composite Material sheet having minimum 0.5 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading chages necessary for satisfactory completion of the work as directed by Engineer -in-Charge.
44
8192
360448
... More
Road work;Providing & fixing junction boards of size 1500 x 1200 mm made out of Type ? XIof ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro Retro reflective sheeting Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of Green Colour & White Letters and fixed over 4MM Alluminium Composite Material sheet having minimum 0.5 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing wit h 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer -in-Charge
21
34327
720867
... More
Road work;Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC: 35, the material should be of BERGER Company/ BERGER Equivalent/ Equivalent brand and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0' degree centigrade to '-10' degree centigrade D) Adhesion : Strong E) Softening point: 102 degree centigrade F) Dried film finish : Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997.(Data communicate vide E-in-C(R&B) SR&CRN, Circular Memo No.RSI/DCE(R)/Con.Er(RS/DEE(RS)/AEE(RS)/2022, Dt:23.11.2022
6913
728
5032664
... More
Road work;Construction of Pavement Quality Concrete un-reinforced, dowel jointed plain Cement concrete pavement of grade M40 with minimum flexural strength of 4.5 MPa at 28 days over a prepared sub base , as per approved mix design including production, transportation to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip/backup rod as per drawing, dowel bar, tie rod, micro fibers,admixtures as approved, curing compound, finishing to lines and grades etc.complete as per specification and drawings for Junction improvement
375
8634
3237750
... More
Road work;Construction of Dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per Table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing and as directed by the Engineer-in-Charge for below CC Pavement DLC Concrete for Junction Improvement
188
4869
915372
... More
Road work;Construction of Granular sub-base by providing HBG material confirming to Grading - VI of MoRT&H Table 400-1 including cost, (excluding seigniorage charges) and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavator / approved means at OMC and compacting with vibratory roller to achieve the desired density etc., complete for finished item of work as per MoRT&H Specification 401 (5th revision) and as directed by the Engineer-in-charge for Junction improvement
188
3745
704060
... More
Road work;Construction of Subgrade with material obtained from borrowed useful earth from outside road boundary MDD of 18 KN/Cum , CBR = 10%, PI < 18%, by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P, complete for finished item of work as per MoRT&H specification 305 (5th revision). Note: The work of subgrade shall be carried out as per Plan & Profile and Payment will be based on levels for finished item of works for Junction Improvement
313
532
166516
... More
Road work;Providing and laying flexible apron on river bed for protection against scour with stone boulder weighing not less than 40kg each complete as per drawing and technical specification as per MORT&H spec no.2507.20 complete for finished item work for Box culvert
253
3265
826045
... More
Road work;Providing and laying of Vibrated cement concrete M 15 Grade Concrete using 40mm , 20mm and 10mm size HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) and conveyance of all materials to site and all labour charges ,centering, batching plant, laying in position, Compacting , Vibrating and curing including all other incidental and all other operational charges of T&P required etc., complete as per MoRT&H Specification 1500,1700, 2100 (5th Revision) For Rigid Apron for Box culvert
134
6393
856662
... More
Road work;Drainage spouts complete as per drawing and technical specifications Clause 1209 MORD & 2705 MORTH for Box culvert
20
1279
25580
... More
Road work;Providing Weep holes in VCC Abutment/ Wing wall/return wall with 100mm Diameter AC pipe extending through the full width of the structure at 1.00m C/C in both horizontal and vertical direction so that the weep holes in each horizontal direction is staggered from the weep holes laying above and below lines as shown in drawing including cost and conveyance of the A.C pipes and labour charges for cutting to required length, placing the pipe with a slope of about 1V : 20H towards stream side face etc., complete for finished item of work for weep holes as per MoRT&H specification 2706 & 2200 (5th Revision) for Box culvert
350
398
139300
... More
Road work;Providing and laying of filter media using 50% of 150 mm IRC soling stone and 50 % of 40 mm HBG metal satisfying the requirements laid down in clause 2504.2.2 of MoRT&H specifications to a thickness of not less than 600mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind the abutment, wing wall and return wall to the full height compacted to a firm condition including cost and conveyance of all metal (excluding seigniorage) charges ,and all labour charges as directed by the departmental officers as per drawing and Technical specifications as per clause 710.1.1 of IRC:78 and Clause 2200 of MoRT&H (5th Revision) for finished item of work for Box culvert
252
3411
859572
... More
Road work;Providing and filling bedding of Gravelly soils around the pipes of Hume pipe culverts suitably compacted / rammed including cost, (excluding seigniorage) and conveyance of materials to site etc., complete as per drawing and MoRT&H ( 5th Revision) and as directed by the Engineer-in-Charge for Box culvert
576
848
488448
... More
Road work;Providing 25.4 mm mastic pads for Longitudinal joints, Transversal expansion joints and Construction joints of approved quality including cost, conveyance and placing in position, etc., complete as directed by the Engineer-in-charge for Box culvert
210
1186
249060
... More
Road work;Providing HYSD bars (Fe-500 From Primary Producers like TATA, SAIL, VSP,JSW and Shyam as approved by Ministry of Steel) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 &2200 (5th revision) and as per I.S.1786 of 1985 for Superstructure RCC items for Box Culvert
8
76605
612840
... More
Road work;Providing HYSD bars (Fe-500 From Primary Producers like TATA, SAIL, VSP,JSW and Shyam as approved by Ministry of Steel) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 &2200 (5th revision) and as per I.S.1786 of 1985 for substructure for Box culvert
28
74291
2080148
... More
Road work;Providing HYSD bars (Fe-500 From Primary Producers like TATA, SAIL, VSP,JSW and Shyam as approved by Ministry of Steel) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 &2200 (5th revision) and as per I.S.1786 of 1985 for RCC items foundation for Box culvert
38
73950
2810100
... More
Road work;Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-40 grade concrete with HYSD reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified for Box culvert
96
2696
258816
... More
Road work;Vibrated reinforced cement concrete M 30 grade using 20mm & 10mm HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) conveyance of all materials to site and labour charges, centering, machine mixing, laying, vibrating, curing etc., including other incidental hire and operational charges of all T&P as per approved drawings and as directed during execution but excluding cost of steel and its fabrication charges for finished item as per SBD specification as directed by the Engineer-in-Charge for approach slab for Box culvert
221
6956
1537276
... More
Road work;Vibrated cement concrete M15 Grade Concrete using 20mm and 10mm size HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) and conveyance of all materials to site and all labour charges , centering, machine mixing, laying in position, Compacting, Vibrating and curing including all other incidental and all other operational charges of T&P required etc., complete as per MoRT&H Specification1500,1700, 2200 (5th Revision) For Approach Slab levelling course for Box culvert
110
6393
703230
... More
Road work;Vibrated reinforced cement concrete M 30 grade using 20mm & 10mm HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) conveyance of all materials to site and labour charges, centering, machine mixing, laying, vibrating, curing etc., including other incidental hire and operational charges of all T&P as per approved drawings and as directed during execution but excluding cost of steel and its fabrication charges for finished item as per SBD specification 1500, 1600, 1700 & 2702 as directed by the Engineer-in-Charge for Wearing Coat over Deck Slab for Box culvert
20
6935
138700
... More
Road work;Vibrated cement concrete M20 Grade Concrete using 20mm and 10mm size HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) and conveyance of all materials to site and all labour charges , centering, machine mixing, laying in position, Compacting, Vibrating and curing including all other incidental and all other operational charges of T&P required etc., complete as per MoRT&H Specification1500,1700, 2200 (5th Revision) for bed protecting for Curtain wall for Box culvert
133
6742
896686
... More
Road work;Vibrated reinforced cement concrete M 35 grade using 20mm & 10mm HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) conveyance of all materials to site and labour charges, centering, machine mixing, laying, vibrating, curing etc., including other incidental hire and operational charges of all T&P as per approved drawings and as directed during execution but excluding cost of steel and its fabrication charges for finished item as per SBD specification as directed by the Engineer-in-Charge for Super structure for Box culvert
96
8158
783168
... More
Road work;Vibrated reinforced cement concrete M 35 grade using 20mm & 10mm HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) conveyance of all materials to site and labour charges, centering, machine mixing, laying, vibrating, curing etc., including other incidental hire and operational charges of all T&P as per approved drawings and as directed during execution but excluding cost of steel and its fabrication charges for finished item as per SBD specification as directed by the Engineer-in-Charge for Sub structure for Box culvert
351
7598
2666898
... More
Road work;Vibrated reinforced cement concrete M 35 grade using 20mm & 10mm HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) conveyance of all materials to site and labour charges, centering, machine mixing, laying, vibrating, curing etc., including other incidental hire and operational charges of all T&P as per approved drawings and as directed during execution but excluding cost of steel and its fabrication charges for finished item as per SBD specification as directed by the Engineer-in-Charge for foundations for Box Culvert
481
7114
3421834
... More
Road work;Providing Vibrated Cement Concrete (1:4:8) mix using 40mm size HBG crushed stone aggregate and fine aggregate conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for levelling course for Box culvert
211
6280
1325080
... More
Road work;Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete excluding seignioarge charges for finished item of work as per MoRT&H specification 304(5th Revision) and as directed by the Engineer-in-Charge for Box culvert
1899
128
243072
... More
Road work;Providing and filling bedding of Gravelly soils around the pipes of Hume pipe culverts suitably compacted / rammed including cost, (excluding seigniorage) and conveyance of materials to site etc., complete as per drawing and MoRT&H ( 5th Revision) and as directed by the Engineer-in-Charge for Pipe culvert
793
848
672464
... More
Road work;Providing, laying Reinforced cement concrete Hume pipes of 1000 mm Dia., NP-4 class for pipe culverts including cost and conveyance of Pipes etc., complete and Labour charges for laying, jointing of 1000mm dia. R.C.C Hume pipes in position including lifting, aligning, lowering and hoisting etc., as per drawing and as per MoRT&H Specification 2900, 2905 and 2906 (5th Revision) and IRC Special Publication No: 13 and as directed by the Engineer-in-Charge for finished item of work for Pipe culvert
752
12632
9499264
... More
Road work;Vibrated cement concrete M20 Grade Concrete using 20mm and 10mm size HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) and conveyance of all materials to site and all labour charges , centering, machine mixing, laying in position, Compacting, Vibrating and curing including all other incidental and all other operational charges of T&P required etc., complete as per MoRT&H Specification1500,1700, 2200 (5th Revision) for Sub Structure for Pipe culvert
885
6742
5966670
... More
Road work;Providing Vibrated Cement Concrete (1:4:8) mix using 40mm size HBG crushed stone aggregate and fine aggregate conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for levelling course for Pipe culvert
355
6280
2229400
... More
Road work;Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete excluding seignioarge charges for finished item of work as per MoRT&H specification 304(5th Revision) and as directed by the Engineer-in-Charge for pipe culverts
2100
128
268800
... More
Road work;Providing HYSD bars (Fe-500 From Primary Producers like TATA, SAIL, VSP,JSW & Shyam Steel as approved by Ministry of Steel) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 &2200 (5th revision) and as per I.S.1786 of 1985 for Drains of R.C.C items for Drains
260
74291
19315660
... More
Road work;Vibrated cement concrete M20 Grade Concrete using 20mm and 10mm size HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost, (excluding seigniorage) and conveyance of all materials to site and all labour charges , centering, machine mixing, laying in position, Compacting, Vibrating and curing including all other incidental and all other operational charges of T&P required etc., complete as per MoRT&H Specification1500,1700, 2200 (5th Revision) for Sub Structure for Drains
5200
6742
35058400
... More
Road work;Providing Vibrated Cement Concrete (1:4:8) mix using 40mm size HBG crushed stone aggregate and fine aggregate conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for levelling course for Drains
650
6280
4082000
... More
Road work;Earthwork excavation in soils upto SDR by mechanical means including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections etc., complete including for finished item of work as per MoRT&H specification 301(5th Revision) and as directed by the Engineer-in-Charge for Drains
7150
54
386100
... More
Road work;Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 440 mm high as shown in drawing in M 20 grade PCC, kerb stone laid with kerb laying machine, all complete as per clause 408 for Road work
17500
429
7507500
... More
Road work;Filling in between median walls with borrowed useful earth from outside road boundary by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P, complete for finished item of work as per MoRT&H specification 305 (5th revision) for Road work
5841
452
2640132
... More
Road work;Construction of earthen shoulders with selective soils obtained from borrow pits with MDD of 18 KN/Cum , CBR = 10%, PI < 18% from approved sources, grading and consoilidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of MoRT&H, including all hire and operational charges of T&P complete for finished item of work as per MoRT&H specification 305 (5th revision) for Road work
4860
407
1978020
... More
Road work;Construction of Pavement Quality Concrete un-reinforced, dowel jointed plain Cement concrete pavement of grade M40 with minimum flexural strength of 4.5 MPa at 28 days over a prepared sub base , as per approved mix design including production, transportation to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip/backup rod as per drawing, dowel bar, tie rod, micro fibers,admixtures as approved, curing compound, finishing to lines and grades etc.complete as per specification and drawings for Road work
54000
8634
466236000
... More
Road work;Construction of Dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per Table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonne vibratory roller, finishing and curing and as directed by the Engineer-in-Charge for below CC Pavement DLC Concrete for Road work
27000
4869
131463000
... More
Road work;Construction of Granular sub-base by providing HBG material confirming to Grading - VI of MoRT&H Table 400-1 including cost, (excluding seigniorage charges) and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavator / approved means at OMC and compacting with vibratory roller to achieve the desired density etc., complete for finished item of work as per MoRT&H Specification 401 (5th revision) and as directed by the Engineer-in-charge for Road work
36855
3745
138021975
... More
Road work;Construction of Subgrade with material obtained from borrowed useful earth from outside road boundary MDD of 18 KN/Cum , CBR = 10%, PI < 18%, by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P, complete for finished item of work as per MoRT&H specification 305 (5th revision). Note: The work of subgrade shall be carried out as per Plan & Profile and Payment will be based on levels for finished item of works
110375
532
58719500
... More
Road work;Construction of Embankment with material obtained from borrowed useful earth from outside road boundary MDD of 15.20 KN/Cum , FSI < 50%, by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P, complete for finished item of work as per MoRT&H specification 305 (5th revision). Note: The work of embankment shall be carried out as per Plan & Profile and Payment will be based on levels for finished item of works
285073
452
128852996
... More
Road work;Forming embankment with excavated earth obtained from roadway excavation for Embankment by mechanical means upto SDR including pre-watering of soil, removal of top soil, excavation of soils, depositing the soils on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P and complete for finished item of work as per MoRT&H specification 305 (5th revision) for Road work
13858
142
1967836
... More
Road work;Earthwork excavation in soils upto SDR by mechanical means including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections etc., complete including for finished item of work for trench cutting as per MoRT&H specification 301(5th Revision) and as directed by the Engineer-in-Charge for Road work
13858
54
748332
... More
Road work;Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness by Mechanical means as per the Techinical Specification Clause 201 MoRTH 5th Revision for Road work
19.83
39698
787211
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%