Public Health And Municipal Engineering Department Tender

Civil works;Sea-Saw 4 seater

Civil works;Spiral Swing

Civil works;Swing Two seater

Civil works;Providing Children play equipment of standard make including cost and conveyance of all material and all labour charges, all operational and incidental charges etc complete.. Slide and Ladder 8 feet

Civil works;BLD-CSTN-3-7-(24) Using Concrete mixture all works up to Plinth Level: Plain Cement concrete nominal mix (1:5:10) prop (Cement : fine aggregate: coarse aggregate ) using 40mm size Hard Granite Machine Crushed Metal including cost and conveyance of all materials like cement, sand, coarse aggregate water etc., to site , labour charges , for mixing , laying, concrete , ramming in 15 cm layers, finishing top surface to the required level curing etc., complete for finished item of work.for foundation and under flooring bed.

Civil works;BLD-CSTN-2-8 (16) : Filling with Sand in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Civil works;Children Play Equipments:-Children Play Area:- BLD-CSTN-2-1 (9) : Earth work excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational, incidental, labour charges such as shoring ,sheeting, planking, strutting, etc. complete for finished item of work,excluding dewatering charges etc as per SS - 20 B (APSS 308).

Civil works;Providing and fixing of SBR (Styrene Butadiene Rubber) Rubber tile flooring made of recycled rubber from truck tyres of size 500mm x 500mm x thickness 25mm with below standards shall be fixed on Cement Concrete floor CC-1:2:4 (75 mm thick) finished with floating coat of neat cement laid with CC Border of thickness 25 mm and PCC- 1:5:10 (100 mm thick).Fixing of tiles shall be done using high grade industrial adhesive of reputed brand. Drainage and proper slope (approximately 1:100) to be provided for sub-base to avoid water accumulation.etc., complete for finished item of work as directed by the Engineer-in-charge. A. The rubber tile must have interlocking pin arrangement, B. The density should not be less than 800kgs/m3, C. The weight of the tile should be 20kg/m2, D. A Polyurethane binder must be used in manufacturing process, E. Top layer of tile with higher density should be 4-7mm thick, F. Granule size of top layer should not be more than 1.5mm, J. The bottom layer should be 18-21 mm thick, K. Granule size of bottom layer should not be more than 4mm & L. The tile should be fire resistant with uniform top layer

Civil works;Supply & Installation of Leg lift. with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 1 Persons B. Overall Sizes : 760 x 305 x 1220 mm C. Seat Size : 300 x 300 mm D. MOC : Fabricated with MS pipes & Tubes. Conforming to IS1161-1998 / IS 4923 with (v) Main Post Pipe : 100 mm NB and (vi) Supporting Structure : 25 mm NB & 32 mm NB , 60x40 mm Rectangular Tube E. Bearings : Deep Groove / Self Aligning Ball Bearings F. Hardware : Grade ?4.6 Galvanized G. Painting : Powder Coated (80-100 microns thickness) H. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Chest Press. with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Persons B. Overall Sizes : 1800 x 700 x 1900 mm C. Seat Size : 300x300 mm D. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only E. Fabricated with MS pipes & Tubes. Conforming to IS1161-1998 / IS 4923 with (iii) Main Post Pipe : 100 mm NB and (iv) Supporting Structure : 25 mm NB & 32 mm NB , 60x40 mm Rectangular Tube F. Bearings : Deep Groove / Self Aligning Ball Bearings G. Hardware : Grade ?4.6 Galvanized H. Painting : Powder Coated (80-100 microns thickness) I. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Shoulder Press. with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Persons B. Overall Sizes : 1800x 700x 1900 mm C. Seat Size : 300x300 D. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only with (i) Main Post Pipe : 100 mm NB and (ii) Supporting Structure : 25 mm NB & 32 mm NB , 60x40 mm Rectangular Tube E. Bearings : Deep Groove / Self Aligning Ball Bearings F. Hardware : Grade ?4.6 Galvanized G. Painting : Powder Coated (80-100 microns thickness) H. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Taichi Spinner (4) wheel with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Persons B. Overall Sizes : 1050 x 1000 x 1350 mm C. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only (i) Main Post Pipe : 100 mm NB (ii) Supporting Structure : 50 mm NB D. Bearings : Deep Groove / Self Aligning Ball Bearings. E. Handle Bars : High Quality Grip Rubber F. Hardware : Grade ?4.6 Galvanized G. Painting : Powder Coated (80-100 microns thickness) H. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Double Cross Walker /Arm Strengthener with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Person B. Over all Sizes : 1100 x 915 x 1430 mm C. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only (i) Main Post Pipe : 100 mm NB (ii) Supporting Structure : 80 mm NB & 60 x 40 mm Rectangular Tubes D. Bearings : Deep Groove / Self Aligning Ball Bearings. E. Handle Bars : High Quality Grip Rubber F. Hardware : Grade ?4.6 Galvanized G. Painting : Powder Coated (80-100 microns thickness) H. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of 3-Person Waist Trainer (Sitting Twister) with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 3 Persons B. Overall Sizes : 1500 x 1500 x 1350 mm C. Seat Size : Ø350 mm D. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only (i) Main Post Pipe : 100 NB (ii) Supporting Structure : 25 NB & 40 mm NB E. Fixed Wheel : Ø 550 mm F. Bearings : Deep Groove / Self Aligning Ball Bearings & Thrust Bearings. G. Hardware : Grade ?4.6 Galvanized H. Painting : Powder Coated (80-100 microns thickness) I. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Leg Press with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Persons B. Overall Sizes : 2000 x 380 x 1650 mm C. Seat Size : 300 x 300 mm D. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only E. Main Post Pipe : 100 mm NB F. Supporting Structure : 40 & 25 mm NB G. Bearings : Deep Groove / Self Aligning Ball Bearings. H. Handle Bars : High Quality Grip Rubber I. Hardware : Grade ?4.6 Galvanized J. Painting : Powder Coated (80-100 microns thickness) K. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of 3-Person Waist Trainer (Standing Twister) with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 3 Persons B. Overall Sizes : 1450 x 1450 x 1350 mm C. Standing Base : Ø300 mm D. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only (i) Main Post Pipe : 100 mm NB (ii) Supporting Structure : 25 NB & 40 mm NB E. Fixed Wheel : Ø 550 mm F. Standing Positions : Equally spaced at 120 deg. each G. Bearings : Deep Groove / Self Aligning Ball Bearings & Thrust Bearings. H. Hardware : Grade ?4.6 Galvanized I. Painting : Powder Coated (80-100 microns thickness) J. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Rowing Machine/ Rower with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 1 Person B. Overall Sizes : 1200 x 700 x 950 mm C. Seat Size : 300 x 300 mm D. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only E. Main Post Pipe : 100 mm NB F. Supporting Structure : 32 mm NB , 60x40 & 80x40 mm Rectangular Tubes G. Handle Bars : High Quality Grip Rubber H. Bearings : Deep Groove / Self Aligning Ball Bearings & Thrust Bearings. I. Hardware : Grade ?4.6 Galvanized J. Painting : Powder Coated (80-100 microns thickness) K. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Big Arm wheel/ Shoulder wheel with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Persons B. Overall Sizes : 850 x 750 x 1920 mm C. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only D. Main Post Pipe : 100 mm E. Supporting Structure : 50 mm NB & 25 mm NB F. Handle Bars : High Quality Grip Rubber G. Bearings : Deep Groove / Self Aligning Ball Bearings. H. Hardware : Grade ?4.6 Galvanized I. Painting : Powder Coated (80-100 microns thickness) J. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Supply & Installation of Air Walker/ Sky Walker with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 1 Person B. Overall Sizes : 1100 x 550 x 1300 mm C. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials or Class: Heavy Duty ('C' Class) Series of pipes only (i) Main Post Pipe : 100 mm NB (ii) Supporting Structure : 25 mm NB & 40 mm NB , 60x40 mm Rectangular Tube D. Standing Base Size : 320 x 135 mm E. Bearings : Deep Groove / Self Aligning Ball Bearings & Thrust Bearings. F. Hardware : Grade ?4.6 Galvanized G. Painting : Powder Coated (80-100 microns thickness) H. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability. I. Bidder shall obtain the approval of the client for the colour code of the Open Gym Equipment before procurement.

Civil works;Providing Open Gym Equipment:- Supplying & Installation of below Open Gym Equipment with one year AMC in identified parks (apprx. Area 156 sq.m) in the ULBs including: 1. Earth work excavation / Site filling/ Leveling 2. Earth Compacting 3. Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering. All work up to plinth level: 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) 100mm thick layer. 4. Cement concrete flooring 1:2:4 finished with a floating coat of neat cement, including cement slurry, including the cost of nosing of steps etc. Complete 75 mm thick layer. 5. Providing and fixing SBR (Styrene Butadiene Rubber) Rubber tile flooring made of recycled rubber from truck tyres of size 500mm x 500mm x thickness 25mm. 6. CC Border. 7. CC foundation for Gym equipment 8. Fixing of equipment (including required bolt, nuts, fixing arrangements) i.e., Nuts & Bolts made of Stainless steel 316 & lock-nut etc 9. The fitness equipment should be designed for minimum 100 Kg or more user weight. 10. Galvanized Steel pipes, cleaned by sand-blasting, then coated with phosphate solution, and finished with electro-static powder coating or the other similar available material meeting the required standard. 11. Anti Rust - Shot Blast/grit blasting of equipment to clean the rust. Electrostatic powder coating technique: To process the pipe surface 12. Columns - The mild steel pipe, column footing plate screw with a pull-burst, the surface rust, acid degreasing, cleaning, phosphate rust after a special process, throwing sand, Imported plastic powder with a double surface household-level spraying layer, electrostatic spray, high-temperature plastic 200 degree baking powder, smooth surface, UV resistant or as specified by the manufacturer's specification. 13. Seat and plastics - LLDPE / HDPE / metal with any protection / composite material with any protection infiltration of anti-ultraviolet, anti-static decolorization element passing, strength, smooth surface, security assurances, weather resistance etc. 14. Platforms - High Strength punching plate, with a special process dealing with wavy surface microscopy, safe and beautiful non-slip resistance. 15. Fasteners - Stainless steel screws to be used, and at the contact point with the columnsrubber pads to be used, screw top cover with a plastic cap, to enhance its security 16. Providing, Fabricating and fixing of one instructional sign (Information Sign) board as showing the detailed specification of Outdoor Fitness Equipment, safe user age, safety precaution, QR Code, Emergency Contact Name & Number etc. has to be fixed at each location and it shall be easily readable, in Good printing, in Telugu and English languages and Contrast visible colour is to be made ultra violet printing on ACM (Aluminum Compose Metal) sheet or equivalent sound sheet, fixed on MS table frame of minimum size 25 x 25 x 2 mm with bracing of same MS tube, supported on two Nos. Mild Steel (MS) post of size 82 x 40 x 2 mm with bottom plate, height about 2.72 M and printing, powder coating weather resistance paint finish. The instructional sign board is to be embedded in suitable cement concrete block foundation in M20 Grade concrete in accordance with the standard specification as per the satisfaction of Engineer-in-charge. Supply & Installation of Air Swing with below standards etc., complete for finished item of work as directed by the Engineer-in-charge. A. Capacity : 2 Persons B. Overall Sizes : 1000 x 890 x 1300 mm C. MOC : All metal pipes shall be Hot Dipped Galvanized Pipes conforming to IS 1239 (Part 1) with GI thickness of 60micron Pipe Materials and Heavy Duty ('C' Class) Series of pipes only D. Main Post Pipe : 100 NB E. Supporting Structure : 25 mm NB , 40 mm NB & 50 mm NB , 80x40 mm Rectangular Tube F. Standing Base Size : 250 mm round base G. Bearings : Deep Groove / Self Aligning Ball Bearings H. Hardware : Grade ?4.6 Galvanized I. Painting : Powder Coated (80-100 microns thickness) J. All open end pipes are covered with SS/LLDPE caps & the equipment is grouted with M18 Foundation Bolts with Concrete strength of M25 for safety & stability.

Civil works;Providing and fixing Village name board size 600x800 mm made out of Type ? XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of Green Colour & White Letters and fixed over 3MM Alluminium Composite Material sheet having minimum 0.30mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials ,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer ?in-Charge.

Civil works;Providing Traffic sign, Marking & Other Appurenances for B.T Roads:- Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per MORTH Section 803.4 and IRC: 35-2015, the material should satisfy the requirements as per MORTH specifications 803.4 and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0' degree centigrade to '-10' degree centigrade D) Adhesion : Strong E) Softening point: 102 degree centigrade F) Dried film finish : Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-2015 and MORTH Section 803.4

Civil works;RBR-FNDN-22 : Collection, Supply and Filling with gravel in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Civil works;Carting of surplus excavated earth up to 5.00 km from the site including loading, unloading charges, cost & conveyance, dumping, labour charges, all leads & lifts and other incidental and operational charges etc., complete.

Civil works;RBR-BASC-9: Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects. -GRADE II

Civil works;RBR-BASC-7: Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respects. - Grade - II

Civil works;RBR-BASC-2(V): Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom as per Tech. specification No 503 MORTH.

Civil works;Providing and applying primer coat with bitumen emulsion (medium setting) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means as per Tech. specification No 502 MORTH.

Civil works;RBR-SBBS-11 B: Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN / Vibratory Roller 80-100 kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406 MORD / MORTH.

Civil works;Construction of Granular sub-base by providing HBG material confirming to Grading - VI of MoRT&H Table 400-1 including cost, (excluding seigniorage charges) and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavator / approved means at OMC and compacting with vibratory roller to achieve the desired density etc., complete for finished item of work as per MoRT&H Specification 401 (5th revision) and as directed by the Engineer-in-charge. (Payment Based on Levels)(R&B Data)

Civil works;Road Widening BT Road:- Forming embankment with borrowed useful earth from outside road boundary by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P , complete for finished item of work as per MoRT&H specification 305 (5th revision)

Civil works;Carting of surplus excavated earth /rock or any debris upto a lead of 5kms from the site to a distance suitable including loading, unloading charges, cost & conveyance, dumping, labour charges, all leads & lifts and other incidental and operational charges etc., complete.

Civil works;Saw cut joints for freshly laid concrete pavement including all material and labour charges as directed by the Engineer in Charge

Civil works;Vaccum drying of freshly laid cement concrete floor using 100% air tight suction mat of suitable size and length, vaccum pump to maintain vaccum pressure 0.7-0.8 atmospheres as per the standard procedure floating with power floater, mechanical trawelling, finishing with sound edges and corners, including hire and operational charges of machinery, labour, fuel etc., complete for finished item of work as directed by Engineer-in-charge of the work.

Civil works;RBR-EECD-15: Construction of earthen shoulders with approved material obtained from roadway cutting with all leads and lifts including pre-watering of soil, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P etc., complete for finished item of work as per MoRT&H specification 305 (5th revision).

Civil works;RBR-CCPV-5-Construction of M30 grade plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS : 383, maximum in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, scareed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge / culvert and construction joints, admixtures as approved, curing of concrete slabs for 14- days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501 MORD.

Civil works;Providing Plain Cement concrete nominal mix M10 grade using 20mm size Graded Hard Granite Machine Crushed Metal including cost and conveyance of all materials like cement, sand, coarse aggregate water etc., to site, labour charges for mixing, laying, concrete, ramming in 15 cm layers, finishing top surface to the required level curing etc., complete for finished item of work.

Civil works;RBR-SBBS-11 B: Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with Vibratory Roller 80-100 kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406 MORD / MORTH.

Civil works;Road Widening CC Road:- Excavation in ordinary soils, up to 3.00 Mts depth below GL by Manual means: Earthwork excavation in all kinds of soil for roadway as per drawings and technical specifications including setting out, construction of shoring and bracing, removal of stumps and other deleterious material, dressing of sides and bottom as per Technical Specification 305 MoRD / 304 MoRTH and as directed by the departmental officer including protecting the existing utility services wherever it is possible during the execution and taking all precautionary measures in the restricted areas for construction of roads including diversion of traffic and backfilling in trenches with excavated suitable material and disposal of remaining earth upto a lead of 50 m, including all incidental and operational charges etc., complete by manual means.

Civil works;Supply of heavy duty long barrel copper lugs confirming to I.S specifications suitable up to 16 sqmm cable etc complete with nuts, bolts and washers. Makes: DMI / Jainson / Dowels

Civil works;Supply of heavy duty type single compression brass cable glands duly nickel plated complete with brass checknut, outer sheath sealing rubber ring and washers suitable for Up to 16.0 Sq.mm 4 Core XLPE insulated armoured cable etc complete. Makes: SMI / Commet / Dowels.

Civil works;Supply of 6-32A SP MCB 10KA, C/D Curve ISI Mark. Makes : Legrand-DX3 / Schneider-Acti9 / Siemens / L&TExora / Cabtree.

Civil works;Supply and laying of 4.0 Sqmm (56/0.3) 2 Core PVC / XLPE Insulated, Flexible Armouring Flexible Copper cable as per IS 7098 / Part-I / 1988 including all transportation charges etc complete. Makes : Finolex / RR kabel / Havells /Polycab / RPG / KEI / Gloster / V-Guard

Civil works;Supply and laying of 16 Sqmm 4 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I). Makes :Torrent / Unicab / Universal /Polycab / Havells / Gloster / KEI / Finolex/ Paragon

Civil works;Supply and laying of 35 Sqmm 3.5 Core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I). Makes :Torrent / Unicab / Universal /Polycab / Havells / Gloster / KEI / Finolex/ Paragon

Civil works;Supply and fixing of Automatic Street Light Control System with Optical Sensor, Low volatage / High voltage trip and reset, operating voltage 380 - 450 V AC, 50 HZ with suitable SMC enclousure of IP 54 protection, MCBs of Legrand / Schneider / L&T / Siemens of 10KA C/D curve and Contactor suitable to control the load of 12KW three phase load with necessary clamping arrangements. Makes : Swadeep Nature Switch / Light Mate / L&T / Siemens / Bajaj.

Civil works;Supply and Transportation including Earth work excavation and laying charges of Outer dia 63mm and Inner dia 51mm double walled corrugated HDPE duct made as per specification BSEN - 500 86/IS 14930 Part-II. with all accessories like couplers, bends, end caps, Ts etc., complete. Makes: DURA LINE (Dura Guard) / Bajaj / Gamson / Ultra Plus.

Civil works;Providing independent earthing for Important equipment with 40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II)

Civil works;Supply and fixing of suitable out door feeder piller box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board,suitable angle iron stand for mounting the feeder pillar with cement concrete, including Supply and fixing of Legrand / Schnieder make 40A 4 Pole Isolator as incomer, 6 Nos 6-32A SP MCBs as out goings, indication lamps, din channel, 6 Sqmm 3 core copper cable for invidual light control, connectors, bus bars, shroudings, gland plates and provision for 3 phase energy meter etc., complete for finished item of work and suitable wiring provision for connecting the nature switch.

Civil works;Supply and transportation of 150 W LED Street light Body made of high grade pressure die ? cast Aluminium alloy with corrosion resistant powder coat, having protective toughened glass cover, Less Glare, IP 66 (Silicon gasket ensures Optical & Electrical compartments are IP 66) protected, wide operating voltage range, P.F > 0.90, System having efficacy >100 lumens/watt, with Ingress protection IP66, Potted driver, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desired by the department and as per IS, CRI>80, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc complete with BIS certification with warranty 50,000 burning hours. The contractor has to furnish the manufacturer warranty letter, LM 79 and LM 80 certificates. LUMINAIRE MAKE : PHILIPS / OSRAM / GE Venture / CROMPTON / BAJAJ / Wipro / Jaquar / Eveready / Halonix / Keselec / HAVELLS / POLYCAB / SURYA / SYSKA /Capart / Fortune Art / FIEM / Panasonic LED MAKE : PHILIPS LUMILEDS / CREE /NICHIA / OSRAM / SAMSUNG / LG LEDs.150 Watts

Civil works;Foundation and erection charges with special T&P, for 9.00Mtrs / 10Mtrs long Octagonal / Conical pole duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.60Mtrx0.60Mtrsx1.40 Mtr size M20 cc work vibrated concreting mixing with necessary steel (15kgs) reinforcement as directed by the field engineers during execution including centering, decentering, water curing as required, soil exacavation, back filling, muffing removal and coil earthing including all labour charges and cost and conveyance of materials etc. complete.

Civil works;Fabrication, Transportation and supply of - 1.5 Mtr sword type or any decorative double arm bracket with dooms. complete with all cessories with MS galvanized 50mm dia Pipe. Makes: BAJAJ / VALMONT / TRANSRAIL /SKIPPER / UTKARSH / LAASMA / CONSOUL

Civil works;Central Lighting :- Fabrication, Transportation and supply of hot-dip galvanized Octogonal Pole with BSEN - 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangement, including chain for anti theft mechanism, supply of suitable boards with bakelite sheet, din channel for MCB's as per IS specification suitable to withstand the wind speed of 180 KMPH for 9 Mtrs height Pole having dimensions Bottom 155mm, Top 70mm with 3mm thick, base plate 260 x 260 x 16mm and 4 Nos of M24 x 750mm long 'J' bolts along with template or equivalent. Makes: BAJAJ / VALMONT / TRANSRAIL / SKIPPER / UTKARSH / LAASMA / CONSOUL

Civil works;Providing P.C.C grade M 15 Nominal mix concrete for structures using 20mm size Graded hard stone aggregate, mechanically mixed, placed and compacted by vibration including curing for 14 days complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 MORD and 1500, 1700 & 2100 MORTH including cost towards material, labour, formwork and all other incidental charges for complete finished item of work as directed by the Engineer in Charge

Civil works;Providing Plain Cement concrete nominal mix M10 grade using 20mm size Graded Hard Granite Machine Crushed Metal including cost and conveyance of all materials like cement, sand, coarse aggregate water etc., to site, labour charges for mixing, laying, concrete, ramming in 15 cm layers, finishing top surface to the required level curing etc., complete for finished item of work.For bed

Civil works;Amendment in 2021-22 : Supply and Filling with HBG stone chips of 2.36mm and below in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work.

Civil works;Central Median with CC Block Single:- Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and brancing, removal of stumps and other deleterious material and desposal upto a lead of 50 m, dressing of sides and bottom and backifilling in trenches with eccavaed suitable material as per Technical Specification 305 MORD / 304 MORTH.