Nuclear Fuel Complex Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Nuclear Fuel Complex - NFC Tender
Civil And Construction
Building Construction
Eprocure
Opening Date12 Mar 2024
Closing Date12 Apr 2024
Tender Amount₹ 3,80,00,000
Costs
EMD
₹ 7,60,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Civil And Other Allied Works For Facelift Of Occupational Health Centre Building In Nfc-hyderabad. Tender Notice No.c/1337/2024
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_NFC_799735_1Bid Award Id
ViewTender No
C/1337/2024Tender Authority
Nuclear Fuel Complex ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Excavation in TRENCHES for pipes, sewers, etc in all soils except soft and hard rock from average ground level including dewatering if necessary, dressing bottom to required level, profile/slope, back filling in trenches with selected excavated materials in layers not exceeding 250 mm, consolidating, leveling, clearing of all the areas involving excavation of all grass,rank vegetation, shrubs,bushes,cutting of trees upto 300mm grith measured at 1.0 mtr above ground level disposing the spoil within a distance of 50m for ,storm water drains, electrical cables trenches etc.,
-
-
-
Upto 1.50 m depth from average ground level
20
-
-
Above 1.50 m to 3.00 m depth from average ground level.
10
-
-
Felling down carefully trees of girth (measured at a height of 1.0m above ground level) as mentioned below including necessary excavation, removal / destruction of roots, filling the excavated pockets thus formed with good earth, compacting the same, cutting the trunks and branches of trees into suitable pieces for transporting, transporting, stacking and disposing the same at the locations as directed by Engineer – in – Charge, etc., complete.
-
-
-
Beyond 60 cm girth upto and including 120 cm girth
12
-
-
Beyond 120 cm girth upto and including 240 cm girth
5
-
-
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared etc. complete as specified and directed.
650
-
-
Filling available excavated earth (excluding rock) in trenches , plinth , sides of foundation etc.., in layers not exceeding 20cm in depth , consolidating each deposited layer by ramming and watering available within NFC premises for all leads and lifts etc, complete as specified and directed.
50
-
-
Lead charges, including loading, unloading, stacking, the disposable Earth, rock, concrete, brick etc. by Mechanical transport for lead within NFC premises .Note: Measurement of lead charges will be based on truck measurements with deduction of voids @20% and 50% for soils and rocks or debris respectively.
-
-
-
for Soil
60
-
-
for Rock/Debris
60
-
-
Providing centering and shuttering using steel shuttering plates at all depths and heights below and above plinth level, vertical, horizontal, inclined including strutting, propping using steel pipes/acro stagging, removal, cleaning of the same for insitu reinforced cement concrete and in plain cement concrete work as required including chamfers, splays, keys, wedges, nails, bracings, brackets and applying one coat of shuttering oil on all shuttering surfaces coming in contact with concrete etc., complete as directed for Foundation, pedestals, plinth beams, etc.,
-
-
-
Below and Upto Finish Floor Level
50
-
-
Above Finish Floor Level
75
-
-
CEMENT CONCRETE of following mix using Pazzolona Portland Cement conforming to IS 1489 (M/s. ACC, Ultra Tech, Raasi, Birla, Coramandal), crushed sand and graded stone aggregates of 20 mm maximum size at and at all depths below plinth level including consolidation, finishing, curing, etc., complete but excluding formwork as per specifications.
-
-
-
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) with min. cement content of 250Kgs/Cum
100
-
-
1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) with min. cement content of 320Kgs/Cum
20
-
-
Reinforced Cement Concrete by insitu mixing by WEIGH BATCHING or RMC of Ultra Tech, Birla Ready Mix make of Grade M - 30 using Portland Pozzolana Cement conforming to IS 1489 Part-I (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal make) and aggregates conforming to IS 383 with graded stone aggregate of 20mm maximum size and sand at all depths and heights including mixing with superplasticizer of make M/s. Fosroc, Sika, BASF,CICO, Pidilite in proportion as per manufacturer’s Specifications, conveying / pumping / placing at all depths / heights below / above plinth level, consolidation, finishing as specified, curing, etc., including providing and placing cover blocks of required sizes in cement mortar 1:1, etc., but excluding Formwork and Steel Reinforcement complete as specified and directed.
-
-
-
Below FFL
8
-
-
Above FFL
15
-
-
Providing and laying autoclaved aerated cement blocks (Grade-I AAC blocks of density 551 to 650 Kgs/Cum conforming to IS 2185, Part-3) masonry with 150/230/300 mm thick or other required size AAC blocks of make M/s NCL, Aerocon, Greenstone in super structure below and above plinth level up to floor V level with approved block laying polymer modified adhesive mortar or in cement mortar 1:4 (1 cement : 4 coarse sand), complete as directed.
10
-
-
Brick work as per IS 2212 using fly ash bricks conforming to IS 12894 of Class Designation 7.5 and above as specified at all height and depths with cement mortar 1:6 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP) : 6 crushed Sand} including raking out joints and simultaneously pointing the joints with the same mortar, curing, scaffolding etc., complete as specified and directed.
25
-
-
HALF BRICK masonry as per IS 2212 using fly ash bricks conforming to IS 12894 of class designation 7.5 or above as specified in partitions walls in cement mortar 1:4 (1 cement: 4 crushed sand), including scaffolding, raking out joints, curing etc. complete and with Reinforced Cement Concrete (RCC) M15 (1:2:4) stiffeners of depth 75mm at every 900 mm height including form work, curing etc., complete as specified and directed, but excluding reinforcement. Note: Reinforcement will be measured and paid for separately under relevant item of schedule.
120
-
-
Filling in bath, W/C, toilet, depressed areas with water proofing brick bat coba of the agency approved by the Dept. at all floors and locations upto the required level and making the surface finished suitable to receive floor finish etc. all complete as per drawings and water proofing agency's specifications & as directed by the Engineer in charge.
50
-
-
Supply, fabrication and erection of Reinforcement bars for Reinforced cement concrete items at and at all depths and heights below and above plinth level with high yield strength deformed bars confirming to IS 1786 with TM Treated steel of grade 500D of Tata, Vizag,Sail, JSW/JSPL make, including transport to site, loading and unloading, making fan hooks of required shape, dowels for bonding masonry, transporting steel to site, decoiling, removing of scales, straightening, cutting, bending, fixing bars with chairs, space bars wherever required, in position with two strings of 18 gauge soft drawn annealed MS binding wire inclusive of its supply etc., complete as specified and directed by Engineer-in-charge.
3000
-
-
Providing and fixing structural stainless steel frame (SS304) for Shera Board Wall Cladding on walls at all heights using S.S. square/ rectangular tube of make M/s. JSW in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of S.S. brackets/ lugs of angle / flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centering and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support Shera board cladding, the stainless steel work will be given a priming coat compatible with the epoxy paint to be done in two or more coats over the priming coat (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. SS screws, nuts, bolts, etc of approved make shall be used. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel clamps shall not be weighed separately and nothing extra shall be paid), complete as specified and directed by EIC.
3500
-
-
Supply, Fabrication and Erection of structural steel work using 3"X1" Apollo pipe with 16 guage 2mm thick with white powder coated , at all levels above plinth level as per Design including supplying of steel sections , cutting , fabricating using welding/bolts,using weld rods of make D&H , Advani , Phillips or its approved equivalent and/or bolts and nuts from approved source for Entrance Porch Area or as directed by Engineer-in-Charge.
Note: - Thickness of Powder Coating should not be less than 100microns .
1500
-
-
Supply, Fabrication and Erection of Structural Steel work using Rolled Steel Joists, Beams, Channels, Plates, etc., at all levels above and below plinth level including supplying of steel sections and plates conforming to BIS 2062 of make Vizag Steel, Tata, SAIL, JSPL, Jindal steels ltd. ,Jindal Ispat of yield strength not less than grade 250 or any other approved manufacturer using ingots of above manufacturer make, loading, unloading, transporting the steel to site of work, cutting, fabricating using welding/bolts, using weld rods of make D&H, Advani, Philips or its approved equivalent and/or bolts and nuts from approved source, erecting using derricks/pulleys/cranes or any suitable means, fixing in position and painting with one coat of approved red oxide zinc chromate primer and two coats of Synthetic Enamel paint as per manufacturers Specifications of make Asian Paint, Berger, Johnson and Nickelson, Nerolac, cleaning the sections /plates by suitable means, etc., complete as directed by the Engineer-in-Charge. Note : The bolts used shall be high tensile bolts of minimum 8.8 designation conforming to IS:3757/ASTM A325 standards. Nuts and washers shall be cadmium /Bronze iridium coated.
-
-
-
For Rolled steel sections
1
-
-
For plain plates/chequered plates.
0.5
-
-
Cement plastering 15 mm thick for internal walls in cement morar 1:4 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP) : 4 River Sand} conforming to IS1542 fininshed smooth at all height above plinth level over brick walls or concrete surface including making necessary grooves in between junctions or brick masonary and RCC and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed.
100
-
-
Cement plastering 20mm thick in Two (2) coats over exterior masonry and concrete surfaces at and at all heights/depths above/below plinth level with base coat in Cement Mortar 1:4 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP) : 4 River Sand} 12mm thick and finishing coat in Cement Mortar1:3 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP) : 3 River Sand} 8mm thick final rendering including addition of approved integrated waterproofing compound @ 2% by weight of cement or as per manufacturer’s Specifications for the base coat of make M/s. Fosroc/Demech/ Huntsman/ Pidilite/ SIKA Qualcrete / MBT/Sunanda Chemicals, making necessary grooves, bands, drip moulds, etc., as required, double steel/tubular scaffolding wherever necessary, curing, etc., complete as specified and directed.
150
-
-
Making good the damaged portion of walls with cement mortar mix (1 cement: 4 coarse sand) of thickness 20mm to 40mm at all height above plinth level over brick walls or concrete surface to restore the level of surface after removal of wall tiles/replacement of pipeline, including fixing of chicken mesh, hacking over surfaces wherever required, scaffolding curing etc., complete as specified and directed.
75
-
-
Cement plastering 6 mm thick for ceiling with cement mortar 1:3 (1 cement :3 river sand) finished smooth finish with including hacking of concrete surfaces, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed.
50
-
-
Cement plastering using white cement based polymer modified self curing mortar of adequate thickness finished smooth finish with including hacking of concrete surfaces, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed by Engineer-In-Charge
50
-
-
Applying 2 (Two) coats of ready made cement based putty of average thickness 1 mm of Birla wall care/J.K. Wall putty over plastered wall surface including cleaning the surface with steel scrapper, wire brush, sand paper etc., filling in crevices, holes, cracks with approved filler etc., finishing the surface neat and smooth without any undulations as specified and directed at all height including required scaffolding and including one coat of external primer of approved make before applying putty.
Note :- Rates are inclusive of scaffolding required at all heights.
2850
-
-
Painting with 3 coats of Acrylic emulsion paint (including primer) interior grade emulsion of Asian Apcolite Suprema or equivalent quality of /Berger/Nerolac makes of first quality and required shade over walls, ceilings etc.,(interior paint) including scaffolding upto all heights, removing whitewash/color wash/old paint, if any, by scrapping with scrubbing machine, sand papering, preparing the surface smooth including necessary repairs to scratches, filling in crevices, holes and cracks etc., with approved filler etc., complete all as specified and directed.
Note:-
1. Removing old paint by using scrubbing machine, preparing the surface smooth including necessary repairs to scratches etc. complete is also included. 2. Rates are inclusive of scaffolding required at all heights.
2000
-
-
Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives -Ultima protek of asian make or Dulux professional water shield flexx or equivalent and including priming coat of exterior primer (asian paints damp proof advance) applied as per manufacturer's specifications.
Note:- 1. Rates should be qouted inclusive of 1 coat of primer and removing old paint by using scrubbing machine, preparing the surface smooth including necessary repairs to scratches etc. complete is also included.
2. Rates are inclusive of scaffolding required at all heights.
850
-
-
Providing and filling cracks acrylic latex flexible crack filler compound " Dr. Fixit Crack -X " by Pidilite Industries for filling plaster cracks in internal and external walls as per manufacturers specifications and as directed by Engineer-in-Charge at all height inluding required scaffolding.
50
-
-
Painting wooden surfaces with one coat of wood primer and two coats of synthetic enamel paint Asian, Pidilite, Johnson & Nicklson, Nerolac, berger, of approved shade including preparing surfaces, cleaning, sand papering, including applying and filling crevices or wherever required suitable filler etc, scaffolding, cleaning, etc., complete.
250
-
-
Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:
1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.
2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.
3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/ grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.
4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs.
The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)
250
-
-
Painting steel surfaces with one coat of zinc chromate primer and two coats of synthetic enamel paint Asian, Pidilite, Johnson & Nicklson, Nerolac, berger, of approved shade including preparing surfaces, cleaning, sand papering, including applying and filling crevices or wherever required suitable filler etc, scaffolding, cleaning, etc., complete.
100
-
-
Providing and laying Fully body/Double charged vitrified tile polished finish of size of Tile 600mm x 600 mm / 600mmX1200mm in floor having thickness as per manufacture specifications ,tiles of 1st quality, non-skid, matt finish and non slipperry, full body/double charged , of make Kajaria,Johnson,Somani and Rak s or equivalent approved make with water absorption less than 0.08% and conforming to S:15622,in all colours and shade, jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with epoxy grout with matching pigment.
Note:
i) Quoted rate shall include extra adhesive required to match the water proofing plaster if any to maintain the lines and plumb of dado.
ii) The quoted rate shall include border / combination of tiles as instructed by the Engineer in Charge
iii)The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly.
-
-
-
In flooring with rustic/matt/glossy finished 600X600mm of full body /double charged vitrified tile of make Somany/Kajari or approved equivalent laid with Flooring with cement based high polymer modified quickset adhesive (Water based) conforming to IS: 15477, in adequate thickness as required at site of make MYK Laticrete,Mapei,Dr.Fixit,Roff or equivalent approved make including grouting of joints with epoxy grout with matching pigment with spacers of 2mm/3mm ,completeas per directions of EIC.
1500
-
-
In skirting/dado of size 600X600mm tile with over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with epoxy grout with matching pigments etc. complete as specified and directed with spacers of 2mm/3mm ,completeas per directions of EIC.
300
-
-
In flooring with rustic/matt finished 600X1200mm of double charged vitrified tile in Flooring with cement based high polymer modified quickset adhesive (Water based) conforming to IS: 15477, in adequate thickness as required at site of make MYK, Laticate,Mapei,Dr.Fixit,RAF or equivalent approved make , including grouting of joints with epoxy grout with matching pigment with PVC spacers of 2mm/3mm etc. , complete as specified and directed.
500
-
-
In skirting/dado of size 600X1200mm tile with over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with epoxy grout with matching pigment.complete as specified and directed with spacers of 2mm/3mm ,completeas per directions of EIC.
90
-
-
Hacking the existing cement, concrete floor , mosaic flooring ,or any other tiling , dado surface etc at an average of 5 to 7 indentation of 3 to 5 mm deep per 50 sqcm with hacking hammers or chisels, cleaning the aears, disposing the debris within a lead of 50 m etc., complete.
2000
-
-
Extra for using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding inlaying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm instead of cement based high polymer modified quickset adhesive (Water based) conforming to IS: 15477, in adequate thickness as required at site .
250
-
-
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite stone for treads/ risers /steps / ramps /wall /window sills of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
85
-
-
Providing nosing and groove cutting (3 Nos. Parallel Groove throughout the length for each step) for treads to stones like marble, granite and kota etc to the required shape etc. complete as specified and directed
100
-
-
Constructing wash basin platform of approximate width 600mm and maximum length upto 3 meters using two machine polished granite slabs (each 16mm to 18mm thick) fixed back to back with araldite including making openings in granite for under the counter wash basins, holes for pillar taps, moulding, rubbing and polishing of cut edges, making recess in the wall, inserting the platform in the wall till 40mm, grouting with cementious grout of Fosroc (Conbexrtra) or approved make, forming nosing at the edges of the counter, etc, supporting the platform using brackets complete as specified and directed.
75
-
-
Providing and fixing factory made single extruded WPC (wood polymer composite) solid door/window frames/chowkhat of following sizes comprising of virgin PVC polymer of K value 57-60, calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non-toxic additives fabricated with mitered joints after applying PVC solvent Cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum and manufactured by RAJSHRI or equivalent, screw withdrawl strength of 990N, minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with propoerty of being termite/borer proof, water/moisture proof and fire retardent and fixed in position with SS dash fastners/Hold fast of required dia and length, painting with required color, complete as directed.
Note : For WPC solid door/window frames , minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
-
-
-
WPC door frame (100X65)
35
-
-
Providing and fixing factory made Decorative (laminated) extruded WPC (wood polymer composite) flush door shutter of following size comprising of virgin PVC polymer of K value 57-60, calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non-toxic additives having minimum density of 650 kg/cum manufactured by RAJSHRI or equivalent, screw withdrawl strength of 1800N(Face) & 900N(Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with propoerty of being termite/borer proof, water/moisture proof and fire retardent and fixing with Stainless steel butt hinges of required size with fully body threaded star headed counter sunk SS scews, including supplying and fixing of necessary fixtures such as tower bolts, round handles (both sides), aldrops (one side), etc .
The doors shall be factory laminated on both sides with 1mm thick laminate of century or greenply.
a) 30 mm thick.
-
-
-
30mm solid WPC flush door shutter-plain
50
-
-
Water proof plaster of 15mm thick in cement mortar 1:3 ,with waterproofing compound make of ( M/s Fosroc , MBT, Sika, Sunanada Chemicals etc.) @ 2% by weight of cement including scaffolding, curing, hacking of concrete surfaces etc. complete as specified and directed.
30
-
-
Providing cement based waterproofing treatment to the sunken floor of water closets, bath rooms, nahanis from inside at all heights above plinth level/ lift area giving injections to the concrete surface as required with cement and approved waterproofing compound solution to fill up all inherent holes, voids, honey-combs, etc., in the concrete, applying waterproof plaster of about 25 mm thick for the floor area of the depression and about 18 mm on the side walls of the depression and continue the vertical treatment if necessary on the walls above proposed floor finish with making surface suitable and even to receive tiles, testing the treatment for water tightness by impounding water for 7 days etc., complete.
250
-
-
Providing water proofing treatment to the roof/gutter or any other required surface with cold applied, Acrylic Elastomeric liquid membrane coating over one coat of crystallization coating system Pidilite / Fosroc / Cica in the following sequence:
a) Cleaning the surfaces from dirt, dust and other contaminations
b) Identifying the areas of leakage by approved means,
c) Pressure grouting the area of leakage with cement slurry admixed with expansive grouting additive of M/s. Fosroc / Pidilite (Dr FIxit Pidicrete AM) or its approved equivalent at a minimum one grout point per 2 Sq.m slab area.or as per site conditions).
d) Exposing, cleaning and filling cracks observed if any in RCC slab with polymer modified mortar compound/ PU sealent.
e) Pre wetting the surface of slab and application of one coat of crystallization coating of M/s Fosroc/Pdilite (Dr Fixit Polypus CP) or approved equivalent Applying two coats of Acrylic Elastomeric liquid membrane coating including prime coat of M/s Fosroc/PIdilte (Dr. fixit primeseal) or approved equivalent, two coats of Acrylic Elastomeric liquid membrane coating of M/s Fosroc/Pidilite (Dr. FIxit Roofseal Ultra) or its approved equivalent all as per approved manufacturer’s specifications and as directed by Engineer in Charge.
650
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11) conforming to IS 15778 of Ashirvad/Supreme or approved make, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe on exposed/recessed/underground surfaces to correct line, level, plumb using clamps as directed. This includes removing of existing pipes and fixtures if required, jointing of pipes & fittings with one step CPVC solvent cement, teflon tape, cost of cutting chases wherever required and making good the same with cement concrete/mortar, cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition including testing of joints at cerain locations complete as specified and directed.
-
-
-
20mm dia-concealed including cutting chases and making good the walls etc
250
-
-
25mm dia-concealed including cutting chases and making good the walls etc
200
-
-
32mm dia-concealed including cutting chases and making good the walls etc
50
-
-
40mm dia-concealed including cutting chases and making good the walls etc
75
-
-
50mm dia-on exposed surface
200
-
-
Providing and fixing in position CPVC ball valves of following sizes of Ashirvad/Supreme make confirming to SDR 11 fittings, including jointing material etc, as specified and directed.
-
-
-
20 mm DN
5
-
-
25 mm DN
5
-
-
40 mm DN
10
-
-
50 mm DN
10
-
-
Supplying and fixing following size uPVC UV-Stabilised soil / waste/rain water pipes (conforming to IS 13592) and fittings (conforming to IS 14735) of Grade B laid in floor & on exposed faces of wall of Ashirvad/Supreme make, including scaffolding, removal of existing pipelines if any, laying the pipe below floor / ground to proper slope and gradient, jointing the pipe with Solvent Cement/Rubber ring gasket, ensuring water-tightness for the pipes laid as per codal provisions, cutting to the required length including short pieces, fittings with & without door, assorted fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, cleaning pipe, single & double Y, vent cowl, gaskets, offsets, Tank / WC connectors, cowls, etc, complete as specified and directed.
-
-
-
75 mm DN
160
-
-
110 mm DN
50
-
-
Providing & laying UPVC under ground drainage pipes & Fittings of Sudhakar/Nandi/Godavari make for storm water drains& sewerage pipes of following size conforming to IS:15328 to proper level & grade, jointing including prviding coupler with cement solvent / welded joints / as per manufacturer's requirement, including encasing the pipe alround using cement concrete 1:3:6 complete to an offeset of D/2 where D= dia of pipe all as per specifictions, drawing and as directed by the E.I.C. item includes Providing and fixing UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc
-
-
-
110 mm DN (SN 8kN/m²-SDR34)
60
-
-
160 mm DN (SN 8kN/m²-SDR34)
40
-
-
Providing and fixing in position UPVC bottle Gully Trap of Supreme (Product code NUPHGT110G)/Ashirvad make of size 200mmX160mm including embedding the trap in 1:2:4 cement concrete, construction of brick masonry chamber in 230 mm thick brick masonry in cement mortar 1:4 over cement concrete bed of 1:3:6 of 100 mm thick, embedding the trap, plastering with cement mortar 1:4, 12 mm thick on inside & outside and all exposed surfaces, finished with a floating coat of neat cement, providing and fixing heavy duty C. I. frame and cover of size 300mmX300mm, 40mm thick cement concrete 1:2:4 bed over brickwork, painting the grating frame and cover with 2 coats of approved anticorrosive bitumastic paint, necessary connection with existing line etc., complete as directed
5
-
-
Providing uPVC Floor Trap / Nahani Trap of following size conforming to IS 14735 with CP jalli on top, fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer's recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient, closing the side inlets with plugs if required etc. all complete as specified and as directed
-
-
-
Nahani Trap of 110 X 75mm size of Ashirvad (70001249)/Supreme make
40
-
-
Multifloor trap of 110 x 75 x 50 mm size of Ashirvad (70001252)/Supreme make
10
-
-
Providing and fixing of best quality PVC P trap for urinals of size 110mm X 110mm of Ashirvad (70002811)/Supreme make or approved equivalent with CP grating on top including necessary 1:2:4 cement concrete for embedding the trap connecting the trap to waste pipe, etc, complete as specified and directed.
20
-
-
Providing and fixing EUROPEAN WATER CLOSET of size close to the dimensions 350mmX480mmX395mm of Jaquar (CNS-WHT-551PSPP/551SSPP)/Parryware make/Hindware or approved equivalent , in white glazed vitreous, with integral 'P' or 'S' trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges, conforming to IS: 2548 (Part I & II), including cutting and making good floor, wall wherever required, as specified and directed
15
-
-
Providing and fixing single flush PVC low level flushing cistern of 10 litres capacity conforming to IS: 7231 (Cico/Jaquar/Hindware(Cat no. C-1010)/Parryware make) with all internal PVC fittings mounted on a pair of brackets of heavy quality with 32 mm n. b. PVC flush pipe with bend of required length with all tools, synthetic adhesive, gasket etc. removing the existing cistern if required, complete including connection to W. C.
23
-
-
Providing and fixing approved ORRISA PATTERN W.C. of size close to 580mm X 440mm of Parryware /Hindware(Cat no. 20042) or approved equivalent in white glazed vitreous chinaware with 'P' or 'S' trap, conforming to IS: 2556.
8
-
-
Providing & fixing vitreous China undercounter/Overcounter Wash hand basin consisting following items of work:- i)Providing vitreous china wash basin conforming to IS 2556 ( part - IV ) and placing the wash basin in position as shown in the drawing or as directed. ii) Providing a pair of either cast iron built - in cantilever type brackets weighing not less than 1.5 kg / each to be embedded in grade M 15 (or the one best suites)cement concrete block of size 100 X 75 X 150 mm or cast iron wall fixing cantilever type brackets weighing not less than 1kg / each with screw holes to be fixed to wall using screws, rawl plugs etc. to support the Wash basin, conforming to IS 775 for Wall hung basin.( For wall hung wash basin) iii) Fixing Vitreous China under / over the counter / semi recessed type Wash Basin and placing it in position over the granite platform as shown in the drawing or as directed including finishing the joints with white cement all complete. ( For under/over counter wash basin ) iv) Cutting holes or chases in wall & reinstating to its original condition, painting all metallic parts with two coats of approved flat oil paint over a coat of primer, finishing the gap with white / matching cement etc.all as per specification and as directed for wall hung basin.. v) Installation and testing the entire assembly to the full satisfaction of Engineer- in- charge.
-
-
-
Providing and fixing best quality vitreous chinaware under the counter WASH BASIN of size close to 605mm x 430 mm x 200mm , of make Jaquar(CNS-WHT-705)/Hindware/Parryware conforming to IS: 2556 Part IV including CP brass waste coupling, necessary supports, removal of wxisting wash basin if required, complete as specified and directed.
20
-
-
Vitreous China semi pedestal Wall hung Wash Hand Basin, 570x480 mm size of HINDWARE Make Studio model Cat. No:10096 & pedestal 11038 or equivalent for quarters
12
-
-
Supplying Stainless steel Sink ' Nirali -' Elegance' - LARGE with Drain board and with 'Anti-scratch surface' of overall size 1145x510 mm ( Bowl size 560 x 410 x 200 mm ), approved make, moulded out of 19 SWG (1 mm ) stainless steel sheet of grade AISI 304 (18/8) with waste coupling conforming to IS 13983, placing and fixing the Sink in position to correct line and level with basket type choke-stop strainer ( waste coupling ), Check nuts etc. including the cost of jointing materials, finishing the edges with white / matching colour cement as per manufacturer's recommendation all complete as per specification and as directed by the Engineer-in-charge.
5
-
-
Providing and fixing URINAL of size close to 385 mm x 325 mm x 635 mm of M/s.Jaquar(URS-WHT-13253N)/Parryware /Hindware make screwed to wall/dado with full threaded C.P. brass waste coupling to urinal, spreader, drain pipe etc. removing the existing urinal if required, complete as specified.
20
-
-
Providing and fixing 15 mm n. b. heavy quality C. P. brass Push Type urinal angle valve confirming to IS 8931 of make Jaquar/Parryware/hindware or equivalent along with all pipe fittings as required.
20
-
-
Providing and fixing in position of best quality rectangular shaped urinal PARTITION with frosted glass (8mm thick) of size 450mmX900MM of Jaquar (JSE-CHR-810US450X)/Hindware/Paryware make or approved equivalent, inclusing removing of existing partition if required as directed by Engineer-in-charge.
15
-
-
Providing and fixing approved quality 6 mm thick plane glass mirror of various sizes with /without 6 mm thick marine ply back including painting the ply wood with two coats of synthetic enamel paint over coat of primer and teak wood moulded frame work of size of 40mm x 20mm alround , polishing the frame with 3 coat of french polish after preparation and making the surface very smooth and final mealamine spray finish, including providing & fixing rawal plug in wall / RCC, drilling screw holes, wooden packing if necessary etc., complete all as directed by EIC.
30
-
-
Providing and fixing heavy quality 15mm C. P. brass wall mounted BIB TAPS of Hindware (Cat no. F730041)/Jaquar/Parryware/Jaquar make or equivalent with wall flange confirming to IS:8931.
20
-
-
Providing and fixing heavy quality 15 mm C. P. brass 2 way bib cock of Parryware /Hindware/Jaquar make (F330004CP) or equivalent with wall flange and confirming to IS:8931.
15
-
-
Providing and fixingin toilets Health faucet of Parryware Make /Hindware/Jaquar (ALD-CHR-573) or equivelent with 1.2 meter long flexible tube or as per manufacturer's specifications in Chrome finish and wall hook etc. complete as directed.
15
-
-
Providing and fixing CP Brass 32mm size heavy quality Bottle Trap of approved quality & make Jaquar (ALD-CHR-769L)/Parryware/ Hindware or approved equivalent, inluding extension pipe if required, removal of existing bottle trap if required, as per the direction of Engineer-in-charge.
35
-
-
C.P brass single lever basin mixer of 'Jaquar' cat. No. ORM-10011B.and also removing the existing one if required.
35
-
-
Providing and fixing 15 mm n. b. heavy quality PVC connector pipesuitable for hot and cold water for Cisterns, Wash basins, gyesers, urinals of suitable length with CP brass unions ends of ZOLOTO/PARRYWARE/HINDWARE/JAQUAR make.
5
-
-
Supplying following C.P Brass Bathroom / toilet accessories of following make and fixing on the wall using CP brass screws, rawl plugs etc. as per manufacturer's requirement all complete at the locations shown and as directed by the E-in-C.
-
-
-
Providing and fixing 150X150 mm recessed type CP brass Toilet Paper Roll Holder with cover of Parryware make/Hindware/Jaquar or equivalent as specified and directed.
15
-
-
Providing and fixing C. P. brass TOWEL RAIL of approved design and make of 600mm length, fixed to wall with C. P. brass screws, screwed on to rawl plugs etc., complete of Parry- ware make/Hindware/Jaquar or equivalent.
10
-
-
Towel Ring Circular/Square with round flange of Jaquar Cat. No. CAN 1121N
10
-
-
Liquid soap dispenser Jaquar CAN 1135N
15
-
-
Providing and fixing CP brass soap dish of make Parryware Code /hindware/Jaquar or equivalent.
15
-
-
Providing and fixing movable grab bar for differently abled of Dolphy make (DHGB0002) or approved equivalent of size 600mm consisting of stainless steel tube with nylon grip, complete as directed by Engineer-in-charge and also removing the existing one if required.
4
-
-
Providing and fixing heavy quality half threaded/full threaded C. P. brass waste coupling of size 32mm of make JaquarParryware/Hindware or approved make.
35
-
-
Providing and fixing 32mm/40mm dia flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
15
-
-
Providing and fixing 15 mm n. b. heavy quality C. P. brass angle valve confirming to IS 8931 of make Parryware Code /hindware (F730039CP)/Jaquar or equivalent.
35
-
-
Providing and fixing heavy quality 15 mm C. P. brass 3 in 1 wall mixer of Parryware/Hindware(F730020CP) wall flange and confirming to IS:8931.
3
-
-
Providing and fixing decorative round shaped C. P. brass SHOWER ROSE if dia 200mm without arm of make Jaquar/Parryware/ Hindware(F160125) or approved equivalent.
3
-
-
Providing and fixing decorative round shaped C. P. brass long shower arm of 450mm length of make Jaquar/Parryware/ Hindware or approved equivalent
3
-
-
Providing and fixing C. P. brass Twin Robe Hook, fixed to wall with C. P. brass screws, screwed on to rawl plugs etc., complete of Parry- ware/Hindware/Jaquar or equivalent
5
-
-
Providing and fixing SS 304 Cloth Hanger with four hooks, fixed to wall or doors with C. P. brass screws, screwed on to rawl plugs etc., complete as directed by Engineer-in-charge.
5
-
-
Providing and fixing 160 mm n.b.un-plasticised PVC rain water pipes with necessary PVC clamps and wooden gutties of approved make conforming to IS: 13592 type ‘A’with injection moulded fittings jointing with approved synthetic adhesive seal rings conforming to IS: 5382 embedding the slab junctions leakproof testing complete in line, level and plumb all as directed.
75
-
-
Dismantling/breaking the existing plain cement concrete surfaces carefully in flooring, ramp etc. to the required size, using pneumatic cutters or any approved means including disposing of debris within a distance of 50 m etc., complete as specified and directed.
20
-
-
Dismantling very carefully the existing reinforced cement concrete at all depths and heights below and above plinth level using pneumatic cutters or any approved means including cutting the reinforcement and transporting bars to departmental stores disposing the debris within the lead of 50 m complete as specified and directed
25
-
-
Dismantling very carefully the existing Brick masonry in cement motor with plastering on both sides very carefully at depths/heights above/below plinth level by suitable methods including erection of suitable scaffolding, stacing of useful materials and disposing the unserviceable debris within the lead of 50m, etc., complete as specified and directed.
50
-
-
DISMANTLING THE CERAMIC TILE / VETRIFIED TILE etc. including dismantling of bedding mortar, stacking of materials within 50 metres lead and disposing of debris within 50 m lead. etc., complete as specified and directed.
500
-
-
DISMANTLING OLD PLASTER OR SKIRTING, raking out joints and cleaning the surfaces for plaster including scaffolding, disposal of debris to the dumping ground within 50 metres lead. etc., complete as specified and directed.
250
-
-
Removing existing wooden/steel /aluminium doors, windows, ventilators etc., including shutters, frames architraves, holdfasts etc., very carefully without damaging the frame shutters glass, etc., and transporintg the dismantled doors, windows, ventilators immediately to the departmnetal stores within NFC premises cleaning, disposing of unserviceable materials within a lead of 50 mts complete as directed
200
-
-
Transportation of removed damaged/corroded doors, collapsible gate ,windows and clerestory windows (steel /aluminium/ wood) shutter including chowkhats,architrave, holdfasts etc., carriage of debris by engaging tractor trolley including cost of fuel, wages of driver and required manpower for loading, transporting up to a lead of 2.0 KM, unloading and stacking in the placed shown by Engineer-in-Charge complete as directed.Note: The size of tractor trolley shall not be less than 3.00 m x 1.90 m x 0.80 m.
25
-
-
Removing and Resetting of material/furniture from each room /corridor/hall etc, complete as specified and directed.
Note :- Rate shall be quoted per Room basis
85
-
-
Dismantling PH items and disposing the the unserviceable debris within the lead of 50m etc., including refilling the excavated gap complete as specified and directed.
-
-
-
Flushing Cisterns/ Urinals / partition /EWC/IWC/ Sink / Basin along with all fittings etc
100
-
-
Dismantling C.I./M.S/G.I/R.C.C./UPVC pipes or any other pipe as per site condition including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge.
-
-
-
a) Upto 150 mm dia.
150
-
-
Removing the wooden door shutter from door frame, including carefully disconnecting of hinges and door closer from the shutter, removing the door stopper, cutting the door shutter from below as per the available height of door frame after tiling in the room, refixing of the door shutter to the door frame and connecting the hinges, door closer and door stopper with the door shutter, complete as directed by Engineer-in-charge.
Notes: New hinges if required to be provided at no extra cost.
85
-
-
Transportation of removed damaged/corroded pipes etc., carriage of debris by engaging tractor trolley including cost of fuel, wages of driver and required manpower for loading, transporting up to a lead of 2.0 KM, unloading and stacking in the placed shown by Engineer-in-Charge complete as directed.Note: The size of tractor trolley shall not be less than 3.00 m x 1.90 m x 0.80 m.
10
-
-
Dismantling very carefully the existing structural steel work at all levels in Collapsible gate/MS structural sections like angles, channels, MS plain/chequered plates, flats, etc., including scaffolding, cutting of structural steel members by gas cutters or by any approved method, removing the nuts, bolts etc., as required, lowering stacking the reusable material at site and transporting the material to Departmental stores etc., complete as directed
100
-
-
Supplying and Fixing the Acrylic Back lit Led Letters of good quality and in accordance to the drawings issued . Complete as specified and directed by Engineer-in-Charge.
Note :- Rates are inclusive of Scaffolding required at all heights.
1
-
-
SHERA BOARD WALL CLADDING :- Providing & fixing decorative surface profile 8mm thick Shera Board external wall cladding which includes Aluminium perimeter channels along the perimeter of ceiling, screw fixed to brick wall with nylon sleeves & SS screws at 610 mm centre. The Aluminium framework of size 25mm X 50 mm(1.5mm thick) and SS 304 screws fixed to framework with 25mm dry wall screws at 230mm centre painted with two coats of Synthetic enamel paint over one coat of primer of required shade and one coat of putty if required including cutting the sheets to required size, providing extra frame work around light fittings fixed with necessary clips and accessories to correct line and levels including scaffolding etc. complete as specified and directed .
540
-
-
Designing, engineering, providing and fixing in position fully sealed and air, water and weather tight structural glazing system comprising of framing system (mullions, transoms etc.) made from extruded, powder coated (min. 30 microns in approved colour) aluminium alloy HE9WP (conforming to IS:733) of commercial quality, free from all defects/ impairing appearance especially selected to fulfill the design requirements spelt out in the specifications; machine cut glass infill panels (of size as per the design) made of 6mm thick hard coated (Glaverbel Stopsol or approved equivalent in Super Silver dark Blue or approved shade) reflective toughened glass, the glazed framing panel formed by means of special structural quality silicone adhesive sealant applied on all four sides (between glazing panel unit and aluminium alloy framing system) and fixed to framing system. The item includes fixing the framing system to the RCC framed structure/ brick walls by providing and fixing necessary Aluminium brackets (with flexible joints), bolts, anchors, other fastening devices etc. (made from Stainless Steel grade 316, rivets and pins of aluminium alloy of appropriate grade as required) self locking type and torque tightening type; also including providing smooth membrane of Teflon (Min. 1.0 mm thickness), providing (at all joints of the framing, glazed panels as well as joints between aluminium frame with concrete and/ or masonry) of adhesive silicon sealant and superior quality approved make EDPM gaskets, preparation of fabrication drawings etc. all complete as directed by EIC.
300
-
-
Providing and fixing CI gratings conforming to IS 1729 for rain water pipe entry mouths/filter bed, etc., including chasing making holes in existing masonry concrete surfaces, refilling with cement concrete 1:2:4 reinstating to the original conditions, painting with two coats of bitumastic paint, all in level and line complete as directed and specified for rain water mouths, filter bed.
100
-
-
Providing and fixing factory made uPVC white colour sliding glazed Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame (115mm and above)X(45mm and above) and both glazed and fly screen sash (44mm and above) X(55mm and above) and 5mm thick toughened glass glazing of make saint gobain or equivalent . Window dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.
185
-
-
Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
Item includes installation of glazing of suitable size as per window frame and thickness 5mm.
-
-
-
Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of frame (64mm and above)X(50mm and above) both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing of 5mm thick toughened glass of make saint gobain of appropriate dimension.
20
-
-
Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of frame (64 x 50 mm and above) , sash (64 x 70 mm and above) & mullion 64 x 70 mm and above all having wall thickness of 1.9 ± 0.2 mm and single glazing of 5mm thick toughened glass of make saint gobain of appropriate dimension.
35
-
-
Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.
Item includes installation of glazing of suitable size as per window frame and thickness 5mm.
-
-
-
Fixed window / ventilator made of frame 55 x 45 mm and above & mullion 55 x 65 mm and above , both having wall thickness of 1.9 ± 0.2 mm and tinted glass of 5mm thickness of make saint gobain or equivalent and of appropriate dimension.
15
-
-
Casting and fixing in position precast reinforced cement concrete covers of required size in RCC M-25 insitu mixing BY WEIGH BATCHER using Portland Pozzolana Cement conforming to conforming to IS 455 Latest Edition (M/s. ACC, Ultra Tech,Chettinadu, Coramandal, KCP) , crushed sand , graded stone aggregate of 10 mm maximum size at and at all depths and heights below and above plinth level including mixing superplastizer (M/s. Fosroc, Demach, Huntsman, Pedilite, Sunanda Chemicals, Agro Chemicals, MBT) in proportion as per manufacturer’s specifications including necessary shuttering, providing and fixing cover blocks of required sizes, consolidation finishing as specified, curing, making casting yard and curing tank, stacking carefully at casting yard and transporting to the site of use placing in position as shown in drawings, aligning, leveling, making good all the damaged surfaces etc., complete as directed for covers for storm water drains/trenches with and without holes.
15
-
-
Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer
10
-
-
ROLLER BLINDS :-Providing and fixing of classic system Blackout fabric Roller Blinds made up of 100% Polyester with Acrylic coating resistant to cracking and fraying.The fixing Brackets are made by steel with powder coating to give greater finish. The fixing arrangements as per direction of EIC. (Area shall measured from bracket to bracket and from top to bottom)
75
-
-
Supplying and Fixing Aluminum Track system (including all accessories ) for Curtains in Hospital:-
100% Pure Aluminum Superior Quality powdered coated channels for better finish and long lasting lustre. Heavy guage- thickness provides more longivity ,strength & Virgin plastic Materials used for accessories fitting to assemble the track. Nylon runners-Hooks with wheels to enable free movement of curtains while hanging on the channel.
Accessories: Ceiling Flange, Suspension Tube, Suspension Rod End Cap, Suspension Star Tubing Screw,Glide Carrier,Aluminium support rods & L-angles etc.
300
-
-
Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-locking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/ black),comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.
With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles
2000
-
-
Supplying and Fixing Hospital Bed Curtains with 100% polyster of which around 5.5ft is Cloth and 1.5ft is net (Total height = 7ft ) and highlights are made with steel groomet ( which is easily washable).
2400
-
-
Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.
Note:-
1) The elevational area of the scaffolding shall be measured for payment purpose.
2) The payment will be made once only for execution of all items for such works.
3) All the items mentioned in this tender has scaffolding included in those items itself . This item if needed will be operated as per the direction of EIC.
350
-
-
Supply, installation, testing and commissioning of 415V TPN Power Distribution Board with 36kA/1sec short circuit rating, with minimum IP 43 made out of 2mm thick CRCA steel with the following components generally as specified in the specification and IE Rules as per components indicated therein.
a. 400 A TPN microprocessor MCCB 36 KA, with O/L, S/C & E/F protection with adjustable settings as incomer with required spreader links and ROM handle. The incomer shall be provided with R/Y/B and ON/OFF/TRIP indication lamps, 1 No. MFM, 1 No. 96 sq mm volmeter and 1 No 96 sq mm Ammeter with selector switches-1 No Incomer
b. 250A TPN SDFU - 1 No
c. 125A TPN SDFU - 4 Nos
d. 63A TPN SDFU - 5 Nos
e. 32A TPN SDFU - 5 Nos Manufacturer shall be CPRI approved.
-
-
-
Supply
1
-
-
Installation
1
-
-
Supply, installation, testing and commissioning of 415V TPN Power Distribution Board with 36kA/1sec short circuit rating, with minimum IP 43 made out of 2mm thick CRCA steel with the following components generally as specified in the specification and IE Rules as per components indicated therein.
a. 125 A TPN microprocessor MCCB 36 KA, with O/L, S/C & E/F protection with adjustable settings as incomer with required spreader links and ROM handle. The incomer shall be provided with R/Y/B and ON/OFF/TRIP indication lamps, 1 No. MFM, 1 No. 96 sq mm volmeter and 1 No 96 sq mm Ammeter with selector switches-1 No Incomer
b. 63A TPN SDFU - 4 Nos
c. 32A TPN SDFU - 6 Nos
Manufacturer shall be CPRI approved.
-
-
-
Supply
1
-
-
Installation
1
-
-
Supply and installation of vertical model double door TPN/SPN Distribution boards with minimun IP 43 of following sizes
Note: RCBO& MCBs shall be C rated and indicative type
-
-
-
8 way vertical TPN MCCB DB with following components.
a. 100 A TPN microprocessor based adjustable MCCB with earth fault release and adjustible settings - 1 No Incomer
b. 32 A TP MCB - 3 Nos
c. 32 A SP MCB - 15 Nos
-
-
-
Supply
6
-
-
Installation
6
-
-
8 way vertical TPN MCB DB with following components.
a. 63A , 100mA FP RCBO - 1 No Incomer
b. 10 A SP MCB - 12 Nos
c. 25A SP MCB - 12 Nos
-
-
-
Supply
6
-
-
Installation
6
-
-
8 Way Horizontal SPN MCB DB with following components.
a. 32 A DP 30mA RCBO incomer - 1 No
b. 10A SP MCB - 2Nos
c. 16A SP MCB - 1 No
d. 25A SP MCB - 1 No
-
-
-
Supply
5
-
-
Installation
5
-
-
Supply and installation of following light fittings owith all accessories like supporting hard ware downrods etc as required to complete the installation in all respects.
-
-
-
LED high efficient 2ft X 2ft, generation -V or better, recess mounted light fitting with CRCA housing, with output 3600 Lumens, Luminaire efficacy of around 120 lm/W, IP20, surge protection of minimum 4KV, driver efficiency 80%, power factor0.95, THD10%, CRI80, CCT-5700K, voltage range 120-270V AC, Ripple5%, Electrical insulation class-1, EMI/EMC compliance.
-
-
-
Supply
220
-
-
Installation
220
-
-
LED high efficient 4ft batten type light fitting with CRCA housing, with output 2000 Lumens, Luminaire efficacy of around 120 lm/W, IP20, surge protection of minimum 4KV, driver efficiency 80%, power factor0.95, THD10%, CRI80, CCT-5700K, voltage range 120-270V AC, Ripple5%, Electrical insulation class-1, EMI/EMC compliance.
-
-
-
Supply
35
-
-
Installation
35
-
-
10 W circular recess mounted LED light fitting with CCT=3500K
-
-
-
Supply
20
-
-
Installation
20
-
-
Supply and fixing of 230V, 1200mm sweep Energy efficient 5 star rated BLDC Ivory coloured ceiling fans with 30W power consumption with required downrods with all required accessories.
Warranty: 2 Years
-
-
-
Supply
60
-
-
Installation
60
-
-
Supply and fixing of 300mm sweep Single phase heavy duty industrial exhaust Fans with air delivery 1100 M3/Hr with all required supports and accessories.
-
-
-
Supply
10
-
-
Installation
10
-
-
Supply and installation of 2 module PVC switchboard fitted with 32A modular socket along with plugtop and another 2 module switchboard fitted with 32A modular MCB. Note: The socket shall be loacted near the AC and the control MCB shall be located at a accessible height ~1.2 M from ground.Switchboard also includes PVC backbox.
-
-
-
Supply
4
-
-
Installation
4
-
-
Supply and installation of modular switch boards along with required PVC/metal back box , face plate, frame of following sizes with latest model rugged modular type sparkproof switches and shuttered universal sockets. Colour of the switches and sockets/frame shall be Grey colour.
-
-
-
2 modular switch board with 1 No 25 A socket
-
-
-
Supply
40
-
-
Installation
40
-
-
2 modular switch board with 1 No 25 A SP MCB
-
-
-
Supply
40
-
-
Installation
40
-
-
2 modular switch board with 2 Nos 2 way 6A Switches
-
-
-
Supply
6
-
-
Installation
6
-
-
6 modular switchboard with 2 No 6A socket controlled by 2 No 6A switch
-
-
-
Supply
30
-
-
Installation
30
-
-
6 modular switchboard with 6 Nos 6A Switches
-
-
-
Supply
8
-
-
Installation
8
-
-
12 modular switchboard with 4 No 6A socket and 4 Nos of 6A switches
-
-
-
Supply
40
-
-
Installation
40
-
-
8 modular switchboard with 1No 2 module Fan regulators, 6 Nos of 6A switches
-
-
-
Supply
20
-
-
Installation
20
-
-
12 modular switchboard with 8 Nos 6A Switches and 2 No 2 module Fan regulators
-
-
-
Supply
25
-
-
Installation
25
-
-
3 modular switch board with 3 Nos of 6A switches
-
-
-
Supply
16
-
-
Installation
16
-
-
2 modular switch board with 1 No RJ11 and 1 No RJ45 socket
-
-
-
Supply
45
-
-
Installation
45
-
-
3 modular switch board with 16A switch and socket
-
-
-
Supply
50
-
-
Installation
50
-
-
Supply and pulling of following sizes of flexible FRZH copper wires to be drawn in already concealed PVC conduit/channels with ferruling on both ends excluding cost of pipes, channels and switch boards.
-
-
-
1.5 Sq.mm FRZH Copper wire
-
-
-
Supply
7000
-
-
Installation
7000
-
-
2.5 Sq.mm FRZH Copper wire
-
-
-
Supply
9000
-
-
Installation
9000
-
-
4 Sq.mm FRZH Copper wire
-
-
-
Supply
3500
-
-
Installation
3500
-
-
Supply and laying of following sizes of 1.1 KV grade XLPE insulated, PVC extruded inner sheathed, armoured, FRLS PVC ST2 outersheathed cable on cable trays/trenches with all accessories
-
-
-
3.5c 50Sq.mm Al cable
-
-
-
Supply
500
-
-
Installation
500
-
-
4c 25 Sq.mm Al cable
-
-
-
Supply
500
-
-
Installation
500
-
-
4c 1.5 Sq.mm Cu cable
-
-
-
Supply
500
-
-
Installation
500
-
-
Providing end terminations for following sizes of 1.1 KV grade XLPE insulated and PVC sheathed armoured cables with required hard ware like heavy duty glands, heavy duty long neck copper lugs etc complete.
-
-
-
3.5c 50Sq.mm Al cable
10
-
-
4c 25Sq.mm Al cable
10
-
-
4c 1.5 Sq.mm Cu cable
10
-
-
Supply and installation of following sizes of 2mm thickness GI perforated cable trays along with tray cover
-
-
-
400 mm width, 50mm height
-
-
-
Supply
50
-
-
Installation
50
-
-
100 mm width, 50mm height
-
-
-
Supply
200
-
-
Installation
200
-
-
Supply and installation of maintenance free earthing stations with copper bonded steel ground rod with around 20mm dia and 3 Mts long , Ground Enhancing Material (GEM), inter connecting earth tape between earthing stations and back fill material.Construction of masonary chamber of 450 x 450 mm with CI cover, earth station markers etc complete. Pit should be as per IS 3043
10
-
-
Supply and fixing of 50 x 6 mm hot dip galvanised GI strip for earthing by clamping on walls/trays/trench with all required accesories
-
-
-
Supply
200
-
-
Installation
200
-
-
Supply and fixing of 25 x 6 mm hot dip galvanised GI strip for lightning protection at a height of 12m by clamping on roof sheets/walls/columns with insulators, clamps and all required hardware.
-
-
-
Supply
300
-
-
Installation
300
-
-
Supply and fixing of 100 mm X 25 mm anodised Aluminium cable tags engraved on black back ground with name of the load along with required hardware for fixing the lables on to the cables.
50
-
-
Supply and installation of panel front rubber mats of size 2 Mts x 1 Mts with 2 mm thick as per latest IS 15652:2006
4
-
-
Supply & pulling of 2 pair 0.5mm telephone cable in PVC conduit/trunking with required accessories etc to complete the job.
1000
-
-
Supply and fixing of 20 Pair metal junction box with disconnection Krone modules and back mount plate
3
-
-
Supply & pulling of 4 pair CAT VI UTP network cable with required accessories to be drawn in existing PVC conduit/channels excluding cost of pipes / channels.
-
-
-
Supply
600
-
-
Installation
600
-
-
Supply and installation of 25 mm dia 1.8 mm thick PVC conduits confirming to IS with accessories like bends, couplers etc in wall , false ceiling etc complete
-
-
-
Supply
2000
-
-
Installation
2000
-
-
Supply and installation of 25 mm dia 1.8 mm thick PVC Junction boxes in wall, false ceiling including covers etc complete
-
-
-
Supply
250
-
-
Installation
250
-
-
Supply and installation of 25 mm dia 1.8 mm thick PVC Junction boxes in wall including chasing of wall, fixing the junction box and filling the chase with cement mortar and making good of the surface etc complete.
-
-
-
Supply
500
-
-
Installation
500
-
-
Supply and installation of 32 x 20 mm DLP plastic trunking system with required clamps for fixing, cover, end caps etc complete including required angles and junctions
-
-
-
Supply
400
-
-
Installation
400
-
-
Supply and installation of 105x50mm with separation partition DLP plastic trunking system with required clamps for fixing, cover, end caps etc complete including required angles and junctions
-
-
-
Supply
150
-
-
Installation
150
-
-
Romoval of existing Panel boards of approx dimension 2000x1800x600mm and making good of the surface. The removed material should be shifted to an identified location about 500m away.
2
-
-
Removal of cables of about 95Sq.mm to 25sq.mm sizes and making good of the surface. The removed material should be shifted to an identified location about 500m away.
200
-
-
Removal of MS/PVC lighting Switchboards/ sockets including its wiring from DB and making good of the surface. The removed material should be shifted to an identified location about 500m away
100
-
-
Removal of light fitting along with their down rods and other accessories, wiring and making good of the surface. The removed material should be shifted to an identified location about 500m away.
200
-
-
Removal of ceiling fans / exhaust fans along with their down rods and other accessories, wiring and making good of the surface. The removed material should be shifted to an identified location about 500m away.
70
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements