Nuclear Fuel Complex Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Nuclear Fuel Complex - NFC Tender
Civil And Construction
Building Construction
Electrical and Electronics
Eprocure
Opening Date21 Sep 2024
Closing Date22 Oct 2024
Tender Amount₹ 7,70,00,000
Costs
EMD
₹ 15,40,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_NFC_826926_1Bid Award Id
ViewTender No
C/1361/2024Tender Authority
Nuclear Fuel Complex ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Declaration by Bidder and Acceptance letter
Tech Forms A to H
BOQ Items
a) Girth from 301 to 600mm.
30
-
-
b) Girth from 601 to 1200mm.
15
-
-
c) Girth from 1201mm and above.
10
-
-
Earthwork excavation in over Areas / foundations upto required depths in all kinds of Soils except Soft and Hard Rock in both dry and wet conditions, dewatering if necessary, backfilling with the approved excavated earth by the sides and in plinth by depositing in layers not exceeding 250mm in thickness, spreading, leveling, consolidating by approved means, dressing the bottom and sides to required levels, profiles, slopes, etc., disposing the surplus earth/spoils within a lead of 50m including clearing of all areas of grass, rank vegetation, shrubs, bushes,trees upto 300mm girth measured 1.00 metre above ground level etc. Complete all as directed and specified.
-
-
-
a) Upto 1.50 m depth from average ground level.
1800
-
-
b) Above 1.50 m to 3.00 m depth from average ground level.
1290
-
-
c) Above 3.00 m to 4.50 m depth from average ground level.
40
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas /foundations in ordinary rock upto the depths specified below including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a distance of 50 m including clearing of all areas of grass, rank vegetation, shrubs, bushes,trees upto 300mm girth measured 1.00 metre above ground level etc. , complete as directed by Engineer-incharge.
-
-
-
a) Upto 1.50 m depth from average ground level.
460
-
-
b) Above 1.50 m to 3.00 m depth from average ground level.
460
-
-
c) Above 3.00 m to 4.50 m depth from average ground level.
310
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas/foundations in hard rock (blasting prohibited) by chieseling, wedging or any other approved method viz. using diesel plasma gun under 3.5kg/sqm pressure , followed by pneumatic chiesseling or using non explosive expansive chemical agents including drilling of holes as specified by manufacturer, filling of expansive chemcial followed by pneumatic chiesseling complete upto the depths specified below including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a distance of 50 m including clearing of all areas of grass, rank vegetation, shrubs, bushes,trees upto 300mm girth measured 1.00 metre above ground level etc.., complete as directed by Engineer-incharge.
-
-
-
a) Upto 1.50 m depth from average ground level.
95
-
-
b) Above 1.50 m to 3.00 m depth from average ground level.
95
-
-
c) Above 3.00 m to 4.50 m depth from average ground level.
65
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead within NFC complete as specified and directed by EIC
3700
-
-
Dewatering underground water or continous seeping water using suitable pump/or pumps of required capacity for pumping out seepage water or mud water including all equipment , manpower, drain pipes, cleaning the area complete as specified and directed. Note :- This item will be measured and paid only if continous pumping of inflow water is to be performed for more than an hour in one go and min capacity of pump shall be 5Hp.
3600
-
-
Lead charges for for the upto 3 KM additional lead over the initial lead of 50 m by mechanical transport, including loading, unloading, stacking, the disposable soil, rock etc., Note: Measurement of lead charges will be based on truck measurement with a deduction of voids @20% and 50% for soils and rock or debris respectively
-
-
-
a) For soil
1500
-
-
b) For Debris/rock
200
-
-
II. CONCRETE (PLAIN AND REINFORCED) :
-
-
-
Plain Cement Concrete (P.C.C) 1:3:6 by insitu mixing using Weigh Batching or RMC using Ordinary Portland Cement(OPC) conforming to IS 269 or Portland Pozzolana Cement (PPC) conforming to IS 1489 Part-1 with Minimum Cementitious Content not less than 250 Kg/Cum (M/s. ACC,Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd. make) with crushed stone sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc., but excluding Formwork, complete as specified and directed.
300
-
-
Reinforced Cement Concrete by insitu mixing using Weigh Batching or approved RMC of Grade M - 35 (Minimum Cementitious Content not less than 440 Kg/Cum) up to specified level using using Ordinary Portland Cement(OPC) conforming to IS 269 or Portland Pozzolana Cement (PPC) conforming to IS 1489 Part-1 (M/s. ACC,Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd. make) with crushed stone sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer of brand M/s. FOSROC ,SIKA,BASF,CICO in proportion as per Manufacturer's Specifications, Pumping / Lifting of concrete to the required heights, Concrete laid to proper level, profile and slope, placing concrete, consolidation, finishing, curing, etc., but excluding Formwork and reinforcement as specified and directed.
-
-
-
Below FFL
835
-
-
Above FFL
495
-
-
Casting and fixing in position precast reinforced cement concrete covers of required size in RCC M-20 insitu mixing BY WEIGH BATCHER using ordinary Portland Cement conforming to IS 8112 (M/s. ACC, Ultra Tech, Raasi, Birla, Coramandal, M/s. Andhra Cement Ltd., KCP), crushed stone sand , graded stone aggregate of 10 mm maximum size at and at all depths and heights below and above plinth level including mixing superplastizer (M/s. Fosroc, Demach, Huntsman, Pedilite, Sunanda Chemicals, Agro Chemicals, MBT) in proportion as per manufacturer’s specifications including necessary shuttering, providing and fixing cover blocks of required sizes, consolidation finishing as specified, curing, making casting yard and curing tank, stacking carefully at casting yard and transporting to the site of use placing in position as shown in drawings, aligning, leveling, making good all the damaged surfaces etc., complete as directed for covers for storm water drains/trenches with and without holes including formwork but excluding reinforcement.
25
-
-
III. FORM WORK :
-
-
-
Providing centering and shuttering using good quality densified film-faced Plywood of at least 12mm thick approved make conforming to IS 4990 including strutting, propping, staging made out of steel frames/H-frames/ Mild Steel (MS) Pipes/Cup and Lock System etc., and removal of the same as required including chamfers, splays, keys, wedges, nails, bracings, brackets and applying One (1) coat of shuttering oil (Cemol/Fosroc make/any other ) on all shuttering surfaces coming in contact with concrete,including PVC cover blocks etc., if required, for insitu Reinforced Concrete and in Plain Cement Concrete works etc., complete as specified and directed. NOTE: The Formwork shall be designed and got approved from the Design Section before erection
-
-
-
a) Below and Upto Finish Floor Level
1275
-
-
b) Above Finish Floor Level
1700
-
-
IV. REINFORCEMENT & STRUCTURAL STEEL
-
-
-
Supply, fabrication and erection of Reinforcement bars for Reinforced cement concrete items at and at all depths and heights below and above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more conforming to IS 1786 of Tata, Vizag steel, Sail, JSW, JSPL make, including transport to site, loading and unloading, making fan hooks of required shape, dowels for bonding masonry, transporting steel to site, decoiling, removing of scales, straightening, cutting, bending, fixing bars with chairs, space bars wherever required, in position with two strings of 18 gauge soft drawn annealed MS binding wire inclusive of its supply etc., complete as specified and as per direction of Engineer- in-Charge.
200
-
-
Supply, Fabrication and Erection of Structural Steel work using Rolled Steel Joists, Beams, Channels, Plates, etc., at all levels above and below plinth level including supplying of steel sections and plates conforming to BIS 2062 of make Vizag Steel, Tata, SAIL, Jindal Ispat or any other approved manufacturer using ingots of above manufacturer make, loading, unloading, transporting the steel to site of work, cutting, fabricating using welding/bolts, using weld rods of make D&H, Advani, Philips or its approved equivalent and/or bolts and nuts from approved source, erecting using derricks/pulleys/cranes or any suitable means, fixing in position and painting with one coat of approved red oxide zinc chromate primer and two coats of Synthetic Enamel paint as per manufacturers Specifications of make Asian Paint, Berger, Johnson and Nickelson, Nerolac, cleaning the sections /plates by suitable means, etc., complete as directed by the Engineer-in-Charge. Note :- The bolts used shall be high tensile bolts of minimum 8.8 designation conforming to IS:3757/ASTM A325 standards. Nuts and washers shall be cadmium/bronze iridium coated.
-
-
-
a) For Rolled steel sections
20
-
-
b) M.S. plates//MS sheets etc.,
5
-
-
Supplying, fabricating, erecting and fixing in position, insert plates/ embedded plates/pipes of GI in medium quality conforming to relevant BIS codes of required shape and size, welding anchoring legs not less than 12mm dia MS rods, placing in position in concrete while casting, including painting with one coat of approved red oxide zinc chromate primer as per drawing in line, level and plumb complete as directed.
2
-
-
V. STONE MASONRY :
-
-
-
Random rubble masonry as per IS 1597 with hard stone with Cement mortar 1:6 (1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.) : 6 crushed coarse sand (conforming to IS 2116)) at all depths and heights including scaffolding, raking out joints, simultaenous flush poining, curing, complete as specified and directed for brick wall foundation.
25
-
-
Supply, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
185
-
-
VI. BRICK MASONRY :
-
-
-
Brick work as per IS 2212 using fly ash bricks conforming to IS 12894 of Class Designation 7.5 and above as specified at height/depth mentioned below with cement mortar 1:6 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.) : 6 crushed coarse Sand (conforming to IS 2116)} including raking out joints, curing, scaffolding etc., complete as specified and directed.
-
-
-
a) At all depths below FFL
50
-
-
b) Above FFL
225
-
-
VII FLOORING :
-
-
-
GSB:
Construction of Granular sub-base by providing HBG material conforming to Grading-ii of MoRTH Table 400-1 including cost, (excluding seigniorage) charges and conveyance of all materials to work site and spreading in uniform layers with motor grader or by approved means, on prepared surface mixing by mix in place method with Rotavator/approved means at OMC and compacting with vibratory roller of 8 to 10 Tons Capacity/approve means to achieve the desired density etc., complete for finished item of work as per MoRTH Specification 401(5th revision and as directed by Engineer-in- Charge. Note: ( Payment will be made based on levels for finished item of work).
970
-
-
Non Metallic Floor Hardener:
Providing over RCC flooring, grade slab when concrete is in green condition, finishing top with hard finishing coat using non –metallic floor hardener of Chhabdur or Hardtop or any other from M/s. Fosroc, STP, MYK, Pedilite, Sunanda Chemicals of approved quality and make at spread rate of 7Kg/Sqm or as specified by manufacturer for heavy duty floor finish including spreading after vacuum dewatering, ramming, consolidation, finishing smooth using power trowel to required levels or slope as specified, curing, etc., complete as specified and directed with vacuum dewatering.
970
-
-
Vacuum Dewatering & Power Trowelling:
Vacuum dewatering of concrete using vacuum dewater technique for evaporation by way of removing the excess water using rigid or flexible suction mat incorporation filler layers and vacuum filler layers and vacuum generator (80 to 90% vacuum is to be applied at the rate of 3 to 5 minutes per 25 mm of depth), finishing with power trowel to get smooth finish all as per specifications, drawings and directions of the Engineer-in-charge for grade slab.
970
-
-
Joints Groove Cutting and Sealing:
Cutting using Diamond saw or any other suitable equipment grooves of size 6mmx12mm in flooring at construction/contraction joints or as directed by design Engineer, including filling with polysulfide sealant of M/s. Foroc, STP, Pidilite, MYK, cleaning the joints using compressed air, drying the joint before application complete as directed.
300
-
-
Providing & fixing following vitrified tiles in various thickness (Thickness to be defined by manufacturer) conforming to IS 15622 for flooring of make Johnson, Somani, Kazaria of required shade, design, colour and pattern laid on 20 mm thick cement mortar 1:4 (1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.): 4 coarse sand) or polymer modified adhesive of make MYK/Roff or approved equivalent including providing joints of 2mm with spacers filled with epoxy grout mix of 0.70 Kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 Kg of resin per kg or as specified by manufacturer) of make Pidilite, MYK. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
-
-
-
a) Glazed Vitrified Tile Matt/Anti-skid/Rustic finish of Size of tile 600 X 600mm.
42
-
-
Providing & fixing glazed vitrified tiles polished finish of of Size of tile 300 X 600mm/600 X 600 or as per drawings for dado, skirting, risers of steps (thickness as specified by manufacturer) of make Johnson, Somani, Kazaria of required shade, design, colour and pattern laid over 12mm thick bed of cement mortar 1:3 or or polymer modified adhesive of make MYK/Roff and jointing and providing joints of 2mm with spacers filled with epoxy grout mix of 0.70 Kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 Kg of resin per kg or as specified by manufacturer) of make Pidilite, MYK of required colour as required, complete as specified and directed.
120
-
-
Providing and fixing 18 mm thick Granite flooring/dado using slabs of gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias, steps and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse Msand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish incuding making holes, molding half round/full round nosing and grooves for antislippery measure etc. complete at all levels as specified and directed.
60
-
-
Providing 4mm thick POLYURETHANE HYBRID FLOORING using UCRETE MF of BASF or equivalent make Heavy Duty floor finish Polyurethane concrete system consists of 1mm thick Scratch coatof UCRETEMF and 3mm thick Self smoothing topping of UCRETEMF along with rectification of any pot holes present with suitable and similar filling material. The surface should be prepared with anchor grooves 8mmx8mm along the perimeter of the floor and around drains, machine legs,colunms etc., along with removing the existing flooring finish by scarification including disposal of debris in the specified area as directed by Engineer-in-Charge and as per manufacturer's instructions. Spexcification : For PU Flooring material: COMPRESSIVE Strength: 53 N/mm2 (BS6319:Part 2) Flexual Strength (ISO 178): 21N/mm2 Dynamic E-Modulus: 14000N/mm2 (ASTM C597-83) Tensile Strength (ISO: R527): 9N/mm2 Concrete Adhesion: Concrete Fails (BS6319: PART 2): Abrasion Resistance BS 8204-2 Class ARO.5 (Taber CS17)120MG Coefficient of Thermal Expansion: 3.6x10.6 OC-1 ASTMC531): Thermal Conductivity (BS874): 0.9W/mo C Surface Resistivity (BS2050: 2X1011ohms: Density (BS6319: Part) : 1970 Kg/m3 Water Adsorption (CP.BM 2/67/2): 0 ml;Surface Spread of Flame: Class 2 (BS476: Part 7).
900
-
-
XIII: DOORS, WINDOWS & ROLLING SHUTTERS ETC :
-
-
-
MS door frames and shutters etc using angles, flats, plates, sheets etc at all levels below/above ground level including supplying steel sections/plate conforming to relevant BIS as per drawings, made up using sections of make(Vizagsteel/Tata/SAIL/Zindal/Saritha/Abhishek make), transporting, cutting, fabricating using welding/bolts, weldrods (D&H, ADVANI, Esaab) including supplying and fixing all iron mongery fittings and fixtures like , Hinges, Tower bolts, Aldrops, locking arrangements, Handles, lugs for frame erecting, fixing in position in concrete 1:2:4 and painting with one coat of approved red oxide zinc chromate primer and two coats of Synthetic enamel paint (Asian Paint, Berger, Johnson And Nickelson, Pedilite, Nerolac) of approved shade for all exposed surfaces, cleaning the sections/plate by complete as directed by Engineer-in-charge for Emergency doors.
800
-
-
Glass Door - Providing and fixing glass door of 12.mm thick clear toughened glass of make SAINT GOBAIN/MODI GUARD supported on approved Branded Hardware/Power coted Aluminium as per the manufacturer's. Cost to be inclusive of joints between glass to be filled with clear sealant, eitching, stickring with 3M glass film of approved design etc., complete as per Approved Design etc, handles, lock., complete.
36
-
-
Floor Spring - Providing & fixing ozone make floor spring glass doors including breaking of floor and making it good with cement grout complete as specified and directed.
6
-
-
Glass Partition :-Providing and fixing glass window with 12mm Thk SAINT GOBAIN/MODI GUARD clear Toughen glass with 3M frosted glass film of approved make supported at top WITH ozone Brand Connector fixing on 18mm thick 710 Bwp Ply framing fixing from slab and Bottom Aluminium ALUMNIUM U Track eith patch fittings and connectors with the manufacturer's specification. Cost to be inclusive of joints between glasses to be filled with clear sealant etc., complete as specified and directed by EIC.
350
-
-
Providing and fixing factory made single extruded WPC ( Wood polymer Composite ) solid door/window/ceosetory windows & other FRAMES / CHOWKHAT comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade ), calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement screwed with full body threaded star headed SS screws having minimum frame density of 750kg/cum , screw withdrawal strength of 2200N (Face ) & 1100 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent and fixed in position with M.S hold fast / lugs / SS dash fastners of required dia and length complete as per direction of Engineer in Charge. ( M.S hold fast / lugs or SS dash fastners). Note : For WPC solid door/window frames , minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
-
-
-
a) Frame size 50 x 100 mm.
25
-
-
Providing and fixing factory made single extruded wpc ( Wood polymer Composite ) solid both side PVC laminated/Marble PVC Sheets flush door shutter of required size comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade ), calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum frame density of 650kg/cum , screw withdrawal strength of 1800N (Face ) & 900 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent, include providing and fixing with stainless steel butt hinges of required size with neccessary full body threaded star headed counter sunk S.S Screws, for each door complete as directed as per direction of engineer in Charge.
-
-
-
a) 30 mm thick.
11
-
-
Supplying and fixing to wooden doors etc. and at all heights above plinth level approved Stainless Steel SS 304 tower bolts conforming to relevant IS specifications (‘KICH’ or its equivalent ) with approved SS screws of appropriate size etc., complete as directed.
-
-
-
a) using 250 mm long, 10 mm shoot.
5
-
-
b) Baby latch
8
-
-
Supplying and fixing to wooden doors at all heights above plinth level approved SS Door handles conforming to relevant IS specifications and with ISI marking ‘Classic’/JYOTHI/KITCH or and of size 22mm dia 300mm long - KICH - 316 grade with approved SS screws of appropriate size etc., complete as directed.
12
-
-
Supplying and fixing to wooden doors approved SS Aldrop of size 250mm long x 16mmrod wth an extra staple conforming to relevant IS specifications and with ISI marking classic/ J.S.E. (ECIE) make with suitable approved SS screws, machine screws or bolts for securing clamps from inside etc., complete as directed.
2
-
-
Supplying and fixing at and at all heights above plinth level hydraulic door closures of ‘EVERITE’/Godrej make or approved equivalent confirming to IS 3564 with all fixtures, fittings and approved screws of appropriate size etc., complete as directed.
5
-
-
Supplying and fixing to doors at and at all heights above plinth level approved best quality S.S hanging floor door stoppers with rubber bushing with necessary screws etc., complete for twin rubber stopper.
2
-
-
Supplying and fixing to wooden doors at and at all heights above plinth level approved 6 lever cylindrical mortice locks of Godrej /Everite make or approved equivalent make comprising brass body and all parts including sticking plates made of brass, stainless steel keys in duplicate, a pair of mortice lock handles of approved pattern of Godrej make or its approved equivalent make with approved cadmium plated brass screws of appropriate size etc., complete as directed to single/double shutters for all doors
5
-
-
IX. PLASTERING AND POINTING :
-
-
-
Cement plastering 6 mm thick for ceiling with cement mortar 1:3 (1 cement :3 river sand) finished smooth finish with including hacking of concrete surfaces, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed.
975
-
-
Cement plastering 15 mm thick for internal walls in cement morar 1:4 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.) : 4 River Sand (conforming to IS 1542)} fininshed smooth at all height above plinth level over brick walls or concrete surface including making necessary grooves in between junctions or brick masonary and RCC , providing & fixing GI plaster mesh/chicken mesh 150 mm wide along route of walls chipped for services, junction between RCC and brick walls and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed.
1700
-
-
Cement plastering 20mm thick in Two (2) coats over exterior masonry and concrete surfaces at and at all heights/depths above/below plinth level with 12mm thick base coat in Cement Mortar 1:4 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.) : 4 River Sand (conforming to IS 1542)}, 8mm thick finishing coat in Cement Mortar1:3 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP) : 3 River Sand (conforming to IS 1542)}, final rendering including addition of approved integrated waterproofing compound @ 2% by weight of cement or as per manufacturer’s Specifications for the base coat of make M/s. Fosroc/Demech/ Huntsman/ Pidilite/ SIKA Qualcrete / MBT/Sunanda Chemicals, making necessary grooves, bands, drip moulds, providing & fixing GI plaster mesh/chicken mesh 150 mm wide along route of walls chipped for services, junction between RCC and brick walls and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed.
1100
-
-
Providing and applying white cement based putty in two coats with average thickness not less than 1 mm, of Birla make or any other approved manufacturer, over the plastered wall surface (external/internal) to prepare the surface even and smooth complete.
2675
-
-
Water proof plaster in cement mortar 1:3 ,with waterproofing compound make of ( M/s Fosroc , MBT, Sika, Sunanada Chemicals etc.) @ 2% by weight of cement including scaffolding, curing, hacking of concrete surfaces etc. Complete a) 15 MM thk for underground drains/cable trench etc.
225
-
-
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:
(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.
(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.
(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge
1050
-
-
(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.
NOTE :- 1)The treatment shall be tested by ponding water for a period of 10 days. If due to location of rain water pipes the average thickness of treatment exceeds 110 mm for easy flow of water the extra brickbat coba will be paid as extra item and the rate for the same to be got approved from the Department before execution 2) The waterproofing treatment is to be guaranteed for bone-dry condition for a period of 10 years in the prescribed proforma. 3) The measurement for payment shall be the entire area of terrace covered by the treatment measured between brick/concrete parapets without plaster and the area of vatas calculated by taking the length of vatas and the height above the finished level of the terrace
-
-
-
X. PAINTING:
-
-
-
INTERNAL PAINTING :- Applying 3 or more coats of interior premium emulsion paint of Asain Apcolite suprema /Dulux interior acrylic premium emulsion of required shed of interior grade, having VOC content less than 50 grams/liters including one coat of approved suitable interior primer at all heights above plinth level inside rooms etc., complete and as complete and as directed.
2675
-
-
EXTERIOR PAINTING :- Applying of Two or more coat of elastomeric liquid applied water proofing membrane of asain paint damp proof advance or Dulux Aquatech Flexible damp proof base coat or on surface of vertical wall shall be applied as per manufacture specification.
Finishing walls with 2 or more coat of 100% Premium acrylic Smooth waterproof exterior finish emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS:15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Dept Tinted) with silicon additives, equal to asain paint ultmia protek or Dulux Professional weathershield Flexx or Paints can be obtained from approved make from M/s. Asian, Dulux, Berger, Johnson & Nicklson, Nerolac, Pidilite or any other make etc., complete and as directed.
1100
-
-
XI. MISCELLANEOUS ITEMS :
-
-
-
Providing and fixing SS railing made out of commercial chromium steel tubes SS 304, of various diameters, of approved make, 2 mm wall thickness, pattern as shown in drawing/as directed including supplying or fabricating, fittings like SS bends, tees, etc., welding the pipes using TIG welding or any other approved method, grinding/buffing the welded joints smooth, erecting the railing in position in line, level and plumb, fixing tailing in position by grouting/or any approved system, cleaning, polishing the joints if required, scaffolding etc., complete all as specified and directed.
350
-
-
Supplying, lowering, laying, RCC SPUN PIPES of class and internal dia mentioned below conforming to IS:458 with necessary collars, laid to correct grade and levels at and at all depths below plinth level including cutting to lengths, jointing with hemp yarn and cement mortar 1:1, caulking the joints and finishing, curing, etc., complete as specified and directed.
-
-
-
a) 150mm NB NP-2
50
-
-
b) 300mm NB NP-2
25
-
-
Providing grouting (including tamping) for foundations, structures, equipments, base plates, anchor holes, etc., with non-shrink, free flow grout of shrinkhomp-30N/Sqmm of M/S A.C.C, Fosroc or equivalent mixed with filler like sand in 1:1, including shuttering wherever necessary at and at all depths and heights below and above plinth level complete as specified and directed. note: Weight of grout used in the work will be measured for payment. However, the rate quoted shall inclusive of all materials.
0.2
-
-
Providing and fixing 110 mm n.b.un-plasticised PVC rain water pipes with necessary PVC clamps and wooden gutties of approved make conforming to IS: 13592 type ‘A’with injection moulded fittings jointing with approved synthetic adhesive seal rings conforming to IS: 5382 embedding the slab junctions leakproof testing complete in line, level and plumb all as directed.
100
-
-
Providing and Fixing Light weight Calcium Silicate False Ceiling at all heights using AEROLITE ceiling Tiles – Tegular Edge/Square Edge of Texture- QUADRA / FINE FISSURED/COSMOS design of plain/pattern of size 595x595mmx15mm, having 100% RH – HUMIDITY RESISTANCE, and Fire Performance - Incombustible as per BS 476: part 4, Noise Reduction Coefficient of 0.15, sound attenuation of 32dB, Light reflectance above 85%, density of 450 Kg/m3, Thermal Conductivity of less than 0.05 W/m K, to be laid on true horizontal level 24 mm exposed hot dipped galvanized steel powder coated sections comprising of main ‘T’ runner suitably spaced at joints to get required length and of size 38mm x 24mm made of 0.35mm thick sheet spaced at 1200mm centre and cross ‘T’ of size 38x24mm made of 0.30mm thick sheet, 1200mm long spaced between main ‘T’ at 600mm centre to centre to form a grid of 600x1200mm and secondary cross ‘T’ of size 600x30x24mm made of 0.30mm thick sheet to be interlocked at middle of the 600x1200mm panel to form grids of 600x600mm, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. The wall angle shall be 24x24x0.4mm to be fixed all around the wall. The vertical gap between the false ceiling at different levels at one point due to ventilation duct or any other obstruction must be closed using the above mentioned calcium silictae tiles with appropriate grid, if required. Main ‘T’ runners to be suspended from the shed upto 12m height using GI slotted cleats fixed to ceiling with 6mm dia. And 50mm long dash fasteners, 6mm GI adjustable rods with galvanized level clips spaced at 1200mm centre to centre along main ‘T’ , bottom exposed width of 24mm of all T- sections shall be pre-painted with polyester paint, all complete at all heights as per specifications and drawings as directed by Engineer-In-charge.
920
-
-
XII: WATER SUPPLY
-
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11) conforming to IS 15778 of Ashirvad/Supreme or approved make, having thermal stability for hot & cold water supply, including all CPVC brass threaded fittings, i/c fixing the pipe on exposed/recessed/underground surfaces to correct line, level, plumb using clamps as directed. This includes removing of existing pipes and fixtures if required, jointing of pipes & fittings with one step CPVC solvent cement, teflon tape, cost of cutting chases wherever required and making good the same with cement concrete/mortar, cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition including testing of joints at cerain locations complete as specified and directed concealed/exposed including cutting chases and making good the walls.
-
-
-
a) For the following Nominal Bore (NB) pipe: 20 mm
20
-
-
b) For the following Nominal Bore (NB) pipe: 25 mm
30
-
-
c) For the following Nominal Bore (NB) pipe: 40 mm
25
-
-
d) For the following Nominal Bore (NB) pipe: 50 mm
50
-
-
Providing and fixing in position CPVC ball valves of following sizes of Ashirvad/Supreme make confirming to SDR 11 fittings, including jointing material etc, as specified and directed.
-
-
-
a) 20mm nb for coolers
1
-
-
b) 25 mm n.b.
2
-
-
c) 40 mm n.b.
2
-
-
d) 50 mm n.b.
2
-
-
Providing hoisting and installing at required elevation double layered moulded HDPE cylindrical vertical water storage tank of 2000 liters of Sintex or Duracon make, with suitable SMC cover at top, coated with UV coating/layer including the cost of labour for making hole in the storage tank for inlet, outlet, scour and overflow and the required fittings/ gaskets, float valve including making necessary supporting system complete as directed
2000
-
-
XIII. DRAINAGE
-
-
-
Providing & laying structured wall UPVC under ground drainage pipes & fittings (SN-8) of Ashirvad/Supreme make for sewer lines of following size conforming to IS:16098 (Part-1) to proper level & grade, jointing including providing coupler with cement solvent / welded joints / as per manufacturer's requirement, UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc, complete as specified and directed
-
-
-
a) 110 mm DN (SN 8kN/m²-SDR34)
30
-
-
b) 160 mm DN (SN 8kN/m²-SDR34)
110
-
-
Supplying and fixing following size GRADE B uPVC UV-Stabilised soil / waste/rain water pipes (conforming to IS 13592) and fittings (conforming to IS 14735) laid in floor & on exposed faces of wall of Ashirvad/Supreme make, including scaffolding, removal of existing pipelines if any, laying the pipe below floor / ground to proper slope and gradient, jointing the pipe with Solvent Cement/Rubber ring gasket, ensuring water-tightness for the pipes laid as per codal provisions, cutting to the required length including short pieces, fittings with & without door, assorted fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, cleaning pipe, single & double Y, vent cowl, gaskets, offsets, Tank / WC connectors, cowls, etc, complete as specified and directed.
-
-
-
a) 75 mm n.b. pipes
25
-
-
b) 100 mm n.b. pipes
30
-
-
Construction of rectangular CHAMBERS of internal clear dimension of mentioned below ( internal clear) in 230 mm thick brick masonry in cement mortar 1:6 over a bed of 150 mm thick 1:4:8 cement concrete in foundation, plastering with cement mortar 1:4, 20 mm thick on inside, and all outside exposed surfaces finished with a floating coat of neat cement, 1:2:4 cement concrete for benching in slope 1 in 30 and channel finished with neat cement, brick corbelling at top if necessary to provide clear opening and providing and fixing CI cover with frame of light duty single seal pattern weight not less than 33 kgs embedded in cement concrete 1:2:4, providing and fixing PVC encaptualted MS rungs of 20mm square, each at 300 mm centre to centre if depth exceeds 800 mm, painting CI cover and frame and CI steps with two coats of bitumastic paint etc. complete-For depth of chamber not exceeding 900 mm. However minimum depth of chamber not less than 450mm.
-
-
-
a) 450x600mm
2
-
-
b) 600x900mm
5
-
-
Extra over above item for depths beyond 900 mm of Rectangular chamber including providing and fixing PVC encaptulate MS rungs 200 square, each @ 300 mm C/C, staggered vertically and horizontally etc., as per specifications.
-
-
-
a) 450x600mm
4
-
-
b) 600x900mm
10
-
-
Providing and fixing in position UPVC bottle Gully Trap of Supreme /Ashirvad make of 160 X 110mm sizes including embedding the trap in 1:2:4 cement concrete, construction of brick masonry chamber in 230 mm thick brick masonry in cement mortar 1:4 over cement concrete bed of 1:3:6 of 100 mm thick, embedding the trap, plastering with cement mortar 1:4, 12 mm thick on inside & outside and all exposed surfaces, finished with a floating coat of neat cement, providing and fixing heavy duty C. I. frame and cover of size 300mmX300mm, 40mm thick cement concrete 1:2:4 bed over brickwork, painting the grating frame and cover with 2 coats of approved anticorrosive bitumastic paint, necessary connection with existing line etc., complete as directed.
3
-
-
Providing uPVC Floor Trap/ Multifloor trap of Ashirvad /Supreme make / Nahani Trap of 110 x 75 x 50 mm size size conforming to IS 14735 with CP jalli on top, fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer's recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient, closing the side inlets with plugs if required etc. all complete as specified and as directed
6
-
-
Providing and fixing of best quality UPVC P trap conforming to IS 14735 for urinals of size 110mm X 110mm with 50mm water seal of Ashirvad /Supreme make with CP grating on top including necessary 1:2:4 cement concrete for embedding the trap connecting the trap to waste pipe, etc, complete as specified and directed..
2
-
-
XIV. SANITARY ITEMS :
-
-
-
Providing and fixing EUROPEAN WATER CLOSET of size close to the dimensions 350mmX480mmX395mm of Jaquar (CNS-WHT-551PSPP/551SSPP)/Parryware make/Hindware or approved equivalent , in white glazed vitreous, with integral 'P' or 'S' trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges, conforming to IS: 2548 (Part I & II), including cutting and making good floor, wall wherever required, including Providing and fixing single flush PVC low level flushing cistern of 10 litres capacity conforming to IS: 7231 (Cico/Jaquar/Hindware(Cat no. C-1010)/Parryware make) with all internal PVC fittings mounted on a pair of brackets of heavy quality with 32 mm n. b. PVC flush pipe with bend of required length with all tools, synthetic adhesive, gasket etc. removing the existing cistern if required, complete including connection to W. C. complete as specified and directed.
4
-
-
Providing & fixing vitreous China undercounter/Overcounter Wash hand basin consisting following items of work:- i)Providing vitreous china wash basin conforming to IS 2556 ( part - IV ) and placing the wash basin in position as shown in the drawing or as directed. ii) Providing a pair of either cast iron built - in cantilever type brackets weighing not less than 1.5 kg / each to be embedded in grade M 15 cement concrete block of size 100 X 75 X 150 mm or cast iron wall fixing cantilever type brackets weighing not less than 1kg / each with screw holes to be fixed to wall using screws, rawl plugs etc. to support the Wash basin, conforming to IS 775 for Wall hung basin.( For wall hung wash basin) iii) Fixing Vitreous China under / over the counter / semi recessed type Wash Basin and placing it in position over the granite platform as shown in the drawing or as directed including finishing the joints with white cement all complete. ( For under/over counter wash basin ) iv) Cutting holes or chases in wall & reinstating to its original condition, painting all metallic parts with two coats of approved flat oil paint over a coat of primer, finishing the gap with white / matching cement etc.all as per specification and as directed for wall hung basin.. v) Installation and testing the entire assembly to the full satisfaction of Engineer- in- charge.
vi) C.P. brass waste of standard pattern, 15 mm n.b. screw down heavy quality C.P. bras stopcock conforming to IS: 781., 32 mm CP brass bottle trap, with extension pieceincluding painting of fittings and brackets, cutting and making good the walls wherever required complete as specified and directed
-
-
-
a) Vitreous China semi pedestal Wall hung Wash Hand Basin, 630x450 mm size of HINDWARE Make Studio model Cat. No:10096 & or equivalent.
3
-
-
Providing and fixing as per IS 2556 flat back half stall urinal of size of 328x558 mm size of Hindware/Jaguar or equivalent for supporting the pan on suitable heavy quality CI wall brackets, 32 mm n.b. heavy quality, approved make CP brass bottle trap with extension piece, fixing with CP brass spreader and suitable heavy quality CP brass waste coupling to urinal basin, CP brass grating, spring based flush valve for operation of water flushing etc., complete as specified and directed.
4
-
-
Providing and fixing Granite Stone slab of approved shade with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.
3
-
-
Providing and fixing in position bevelled plain edged mirror 600 x 450mm made out of best Indian glass of 6 mm thick of approved manufacturer, mounted on plywood sheet/ plain AC sheet of 6 mm thick fixed in position with four number of CP brass screws with detachable CP brass caps, washers, rawl plugs, etc., complete as directed.
3
-
-
Providing & fixing in position following type CP fittings/ Fixtures/Faucets of 15 mm nominal dia. with ISI mark/ approved make including providing & fixing specials, wall flanges and fixing to concealed / exposed pipe line with leak proof threaded joints using tephlon tapes, testing the joints hydraulically to a pressure of 10 kg./ sq.cm, rectifying the leaky joints if any, including cleaning etc. complete all as per specifications.
-
-
-
a) Providing and fixing heavy quality fancy variety C.P. brass screw down BIB TAPS of M/S. Jaguar/Hindware make conforming to IS: 8931 on .CPVC lines- size 20mm.
4
-
-
b) C.P brass 2 Way Bib Cock with wall flange of Jaguar Cat.No. ORM 10041
4
-
-
c) Proving and fixing in toilets Health faucet of Jaguar Make (ALD-CHR-573) or equivalent with 1 metre long Easy flex tube in chrome finish and wall hook etc., complete as directed.
4
-
-
d) CP brass waste coupling 32 mm size with 80 mm height as per Jaquar cat. No. ALD-705/709 for wash basin.
3
-
-
e) C.P brass single lever basin mixer of 'Jaquar' cat. No. ORM-10011B.
3
-
-
Supplying following C.P Brass Bathroom / toilet accessories of following make and fixing on the wall using CP brass screws, rawl plugs etc. as per manufacturer's requirement all complete at the locations shown and as directed by the E-in-C.
-
-
-
a) Stainless steel Toilet Paper Roll Holder, recessed type with flap of Jaguar Cat. No.AHS - 1553
4
-
-
b) Liquid soap dispenser Jaquar CAN 1135N
3
-
-
c) Stainless steel Towel Rail/Grab bar of Jaquar Cat. No. AHS-1507.
2
-
-
d) CP brass double Coat Hook of Jaguar Cat. No. AKP-35761P.
4
-
-
e) Glass shelf 600 mm long as per Jaquar cat. No: ACN-1171N
2
-
-
f) Towel Ring square with round flange of Jaquar Cat. No. CAN 1121N
3
-
-
XV: DISMANTLING ITEMS:
-
-
-
Dismantling/breaking the existing plain cement concrete surfaces carefully in flooring, platforms etc. to the required size, using pneumatic cutters or any approved means including disposing of debris within a distance of 50 m etc., complete as specified and directed.
30
-
-
Dismantling very carefully the existing reinforced cement concrete at all depths and heights below and above plinth level using pneumatic cutters/JCB Hydraulic Breakers or any approved means including cutting the reinforcement and transporting bars to departmental stores disposing the debris within the lead of 50 m complete as specified and directed for RCC pedestals.
150
-
-
Dismantling very carefully the existing Brick masonry in cement motor with plastering on both sides very carefully at depths/heights above/below plinth level by suitable methods including erection of suitable scaffolding, stacing of useful materials and disposing the unserviceable debris within the lead of 50m, etc., complete as specified and directed.
10
-
-
Dismantling very carefully the existing RR masonry in basement below/above FFL at all depths and heights including erection of suitable scaffolding, stacking of useful materials and disposing the the unserviceable debris within the lead of 50m etc., complete as specified and directed,
10
-
-
Removing soling from flooring/pavement, stacking useful materials like stones within 50m lead, disposing of unserviceable materials as directed.
30
-
-
Dismantling RC. Hume pipes including excavation and refilling trenches after taking out the pipes, manually / by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-Charge for 600 mm nominal dia pipes
-
-
-
a) Up to 600mm dia.
50
-
-
Dismantling very carefully the existing MS/GI/CI pipe of various dia for various services/hand rail with all fittings and fixtures etc., and stacking with in a lead of 50 m.
-
-
-
a) Upto 40 mm dia.
150
-
-
b) Above 40mm dia.
100
-
-
Removal of existing fire hydrant line of 50/80/100/150/200 mm n.b., excavating the equired length, cutting the pipe line after shutdown, handling over the pipe line to the departmental stores. Note: Earthwork excavation required for the work will be measured under relevant item.
75
-
-
Dismantling and stacking within 50 metres lead, T or L iron or struts including all earth work and dismantling of concrete etc. in base of.
-
-
-
a) T or L iron or pipe
10
-
-
Removing carefully existing chainlink fabric from angle iron posts and struts by removing hook bolts, nuts, etc, straightening GI rods (vertical as well as horizontals) etc., rolling back the removed chainlink, collecting hooks, bolts and nuts, stacking including cutting of iron angle posts, dismantling of PCC pedestals, transporting the materials to Departmental stores etc., complete as directed by Engineer-in-charge. Note:
Area of the chain link fabric will be measured for payment.
30
-
-
Dismantling very carefully the existing structural steel work at all levels in MS structural sections like angles, channels, MS plain/chequered plates, flats, etc., including scaffolding, cutting of structural steel members by gas cutters or by any approved method, removing the nuts, bolts etc., as required, lowering stacking the reusable material at site and transporting the material to Departmental stores etc., complete as directed
15
-
-
ELECTRICAL ITEMS :- Supply and installation of 600 mm width, 75mm height with minimum 2mm thickness GI ladder type cable trays along with bends and couplers. Suitable test certificate shall be submitted for galvanisation.
Rate should also include the required bolts and nuts for fixing of supports
-
-
-
Supply
300
-
-
Installation
300
-
-
Supply and installation of 300 mm width, 50mm height with minimum 2mm thickness GI perforated cable trays along with cover, bends and couplers. Suitable test certificate shall be submitted for galvanisation.
Rate should also include the required bolts and nuts for fixing of supports
-
-
-
Supply
150
-
-
Installation
150
-
-
Suply and installation of structural steel like channels, angles etc for fabriaction and erection of cable trays supports, light fitting supports etc and painting of the same with red oxide and 2 coats of grey enamel paint. Rate should also include the required bolts and nuts for fixing of supports
Make of Structural steel: TATA, Vizag Steel, Jindal Ispat, SAIL
-
-
-
Supply
1000
-
-
Installation
1000
-
-
Supply, installation, testing & commissioning of 50X6 mm hot dip galvanised GI earth strip for ground conductors fixed with no.10 GI wood screws & 1-2 mm thick GI saddles with G.I machine screws or in ground at 750mm below, interconnection of earth strip with welded joints and GI nut bolts & washers, painting with two coats of metallic Aluminium paint for above ground portion & painting with two coats of black bituminous compound for earth strip in ground etc. Suitable test certificate shall be submitted for galvanisation.
Note: Excavation for this item measured seperately
-
-
-
Supply
500
-
-
Installation
500
-
-
Supply and fixing of 25 x 6 mm hot dip galvanised GI strip for lightning protection at a height of 12m by clamping on roof sheets/walls/columns with insulators, clamps and all required hardware.
-
-
-
Supply
1000
-
-
Installation
1000
-
-
Supply and fixing of 25 x 3 mm hot dip galvanised GI strip for lightning protection at a height of 12m by clamping on roof sheets/walls/columns with insulators, clamps and all required hardware.
-
-
-
Supply
200
-
-
Installation
200
-
-
Supply and installation of 25 mm dia 2 mm thick PVC conduits of Sudhakar/AKG make confirming to IS with accessories like bends, couplers etc in roof slab, wall including chasing of wall fixing the conduits and filling the chase with cement mortar and making good of the surface etc complete
700
-
-
Supply and installation of 25 mm dia 1.5 mm thick PVC Junction boxes of Sudhakar/AKG make in wall including chasing of wall, fixing the junction box and filling the chase with cement mortar and making good of the surface etc complete
70
-
-
Supply and installation of Sudhakar/AKG make 25 mm dia 1.5 mm thick PVC Deep junction boxes in slab
10
-
-
Supply and installation of 150 mm dia MS fan boxes with MS hook for supporting the fan/light fitting on to the ceiling with suitable cover
70
-
-
Supply and Installation of 16 guage sheet steel switch board boxes of following sizes including chasing of wall and filling the gap with cement mortar and making good of the surface etc complete.
Make: Legrand or equivalent
-
-
-
3 module
10
-
-
8 module
10
-
-
12 module
20
-
-
Supply and installation of Legrand/ Hager/Siemens make 20 A 2pole & Earth Metal clad power socket including plug top and SP 25A MCB to be fixed by concealing.
20
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements