Nuclear Fuel Complex Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Nuclear Fuel Complex - NFC Tender
Electrical Goods and Equipments
Electrical and Electronics
Eprocure
Opening Date18 Aug 2023
Closing Date16 Sep 2023
Tender Amount₹ 1,38,55,000
Costs
EMD
₹ 2,77,100Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Vrv Vrf Ac System For Computer Building In Nfc
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_NFC_767117_1Bid Award Id
ViewTender No
E651Tender Authority
Nuclear Fuel Complex ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
VRF VRV AC system with Air Cooled ODU Refrigerant copper piping Insulation power cabling control cabling earthing structural steel fabrication works MCC panel etc for New Computer Division Bldg at NFC
BOQ Items
... More
INDOOR UNITS ( Ceiling suspended Cassette type AC) Supplying, installation, testing and commissioning of following minimum capacity 4-way flow - VRF/VRF based - ceiling mounted Cassette type Indoor unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve , outer cabinet , high lift drain pump, fresh intake provision , shall have four way supply air grills on sides & return air girll in center , cord less remote control with LCD display for controlling the indoor unit, display, addressable panel, required refnet joints etc. complete as required suitable for operation on Single Phase, 230 Volts, +/- 10%, 50 Hz. AC supply, complete as required. The IDU shall have automatic force shut down provision in case of fire on recieving signal from BMS system . The Cooling capacity of Indoor Unit will be at air inlet condition of 27 Degree C DB and 19 Degree C WB temperature. NOTE : Each Cassette type AC (IDU) Unit shall be provided with Corded remote controller with LCD display and cordless remote controller.
-
-
-
... More
Supply of 1.5 TR, Ceiling suspended - Cassette type Indoor unit.
3
-
-
... More
Erection of 1.5 TR Ceiling suspended - Cassette type - Indoor unit
3
-
-
... More
Supply of 2.0 TR, Ceiling suspended - Cassette type Indoor unit.
15
-
-
... More
Erection of 2.0 TR Ceiling suspended - Cassette type - Indoor unit
15
-
-
... More
Supply of 2.5 TR, Ceiling suspended - Cassette type Indoor unit.
2
-
-
... More
Erection of 2.5 TR Ceiling suspended - Cassette type - Indoor unit
2
-
-
... More
Supply of 3.0 TR, Ceiling suspended - Cassette type Indoor unit.
10
-
-
... More
Erection of 3.0 TR Ceiling suspended - Cassette type - Indoor unit
10
-
-
... More
Supply of 4.0 TR, Ceiling suspended - Cassette type Indoor unit.
12
-
-
... More
Erection of 4.0 TR Ceiling suspended - Cassette type - Indoor unit
12
-
-
... More
Supply of 5.0 TR, Ceiling suspended - Cassette type Indoor unit.
2
-
-
... More
Erection of 5.0 TR, Ceiling suspended - Cassette type Indoor unit.
2
-
-
... More
VRF Multi Kits / Refnet joints - for Outdoor Units: Supply & installation , testing , commissioning of multi connection Joint / Ref Net for double ODU connections at - Outdoor Units . It should be complete as per the technical specifications compatable for VRF/VRF System ..
-
-
-
... More
Supply
6
-
-
... More
Erection
6
-
-
... More
VRF Multi Kits / Refnet joints - for INDOOR UNITS : Supply & installation , testing , commissioning of Imported Y/T refnet joints with insulation to connect indoor units with main header as per the approved drawing. It should be complete as per the technical specifications compatable for VRF/VRF System . 1 set will comprise of 2 Y/T Refnet joints each for suction & discharge lines
-
-
-
... More
Supply
38
-
-
... More
Erection
38
-
-
... More
REFRIGERANT COPPER PIPING : Supply, installation, testing and commissioning including Pressure testing , vacuum & commissioning of the refrigerant copper piping soft/ hard drwan copper piping for VRF/VRV systems connected between IDU & ODU of different sizes as below . Complete refrigerant copper piping work with fittings ,with suitable adjustable ring type hanger supports, jointing / brazing including accessories , insulated with XLPE Class-O tubular insulation / with Class O Closed cell elastometric nitrile rubber sleeves sections of specified thickness as given below for Suction and Liquid lines , all the acessories as per specifications as required. Party has to submit the OEM certificate stating that copper piping is manufactured for VRF/VRV systems. Refrigerant copper piping sizes, quality & wall thickness as per the OEM recommendations of VRF/VRV - AC System. Entire refrigerant coppe piping from IDU(s) to ODU(s) should be rapped with GI perforated sheet to avoid rat bite.
-
-
-
... More
Supply - 6.40 mm (1/4") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
35
-
-
... More
Erection- 6.40 mm (1/4") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
35
-
-
... More
Supply - 9.52 mm (3/8") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
320
-
-
... More
Erection - 9.52 mm (3/8") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
320
-
-
... More
Supply - 12.7 mm (1/2") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
145
-
-
... More
Erection - 12.7 mm (1/2") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
145
-
-
... More
Supply - 15.90 mm (5/8") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
410
-
-
... More
Erection- 15.90 mm (5/8") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
410
-
-
... More
Supply -19.10 mm (3/4") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
230
-
-
... More
Erection -19.10 mm (3/4") dia (OD) - Soft drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
230
-
-
... More
Supply -22.20 mm (7/8") dia (OD) - Hard drawn with tube thickness 1.2 mm with 19 mm thick insulation
40
-
-
... More
Erection -22.20 mm (7/8") dia (OD) - Hard drawn with tube thickness 1.2 mm with 19 mm thick insulation
40
-
-
... More
Supply -25.4 mm (1") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
90
-
-
... More
Erection -25.4 mm (1") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
90
-
-
... More
Supply -28.60 mm (1 1/8") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
110
-
-
... More
Erection -28.60 mm (1 1/8") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
110
-
-
... More
Supply -31.8 mm (1 1/4") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
30
-
-
... More
Erection-31.8 mm (1 1/4") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
30
-
-
... More
Supply-35.40 mm (1 1/2") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
200
-
-
... More
Erection-35.40 mm (1 1/2") dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
200
-
-
... More
Supply-41.30 mm dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
30
-
-
... More
Erection -41.30 mm dia (OD) - Hard drawn copper with tube thickness 1.2 mm with 19 mm thick insulation
30
-
-
... More
UPVC Piping: Supplying and fixing of following sizes of ISI marked, rigid UPVC piping for condensate water disposal with suitable support along with accessories & insulated with 9 mm thick closed cell elastomeric nitrile rubber as required for Indoor Units
-
-
-
... More
Supply - 25 mm OD
200
-
-
... More
Eretion - 25 mm OD
200
-
-
... More
Supply -32 mm OD
220
-
-
... More
Erection-32 mm OD
220
-
-
... More
Supply-40 mm OD
100
-
-
... More
Erection-40 mm OD
100
-
-
... More
CONTROL CABLES: Supply & Laying of control transmission cabling cum control wiring with following sizes of FRLS PVC insulated, PVC sheathed copper conductor in PVC pipe with fittings , clamps, including making connections etc. as reqd.for Indoor Unit (IDU) to Outdoor Unit (ODU) including making end termination with brass compression gland and copper lugs.
-
-
-
... More
Supply - 3 core x 1.00 sq.mm
1300
-
-
... More
Erection - 3 core x 1.00 sq.mm
1300
-
-
... More
Supply - 3 core x 1.50 sq.mm
1300
-
-
... More
Erection - 3 core x 1.50 sq.mm
1300
-
-
... More
POWER CABLES: Supply & Laying of power cable from MCC to ODUs with following sizes of FRLS PVC insulated copper conductor aromored in PVC pipe with fittings , clamps, etc. including making connections etc. as reqd.from MCC Panel to Outdoor Units (ODU) including making end termination with brass compression gland and copper lugs.
-
-
-
... More
Supply - 4 Core X 16.0 Sq.mm
200
-
-
... More
Erection - 4 Core X 16.0 Sq.mm
200
-
-
... More
Supply - 4 Core X 35.0 Sq.mm
200
-
-
... More
Erection - 4 Core X 35.0 Sq.mm
200
-
-
... More
CABLE TRAYS: Supply & Installation of following size of perforated Hot Dipped Galvanised Iron Cable tray & GI Cover ( Galvanisation thickness not less than 50 microns) with perforation not more than 17.5% in conveinet sections, joined with connectors, suspeneded from the ceiling with GI suspenders including GI bolts & nuts , / MS supports, etc. as required at site.
-
-
-
... More
Supply-150 mm widith X 75 mm depth X 1.6 mm thickness
100
-
-
... More
Erection-150 mm widith X 75 mm depth X 1.6 mm thickness
100
-
-
... More
Supply-200 mm width X 75 mm depth X 1.6 mm thickness
150
-
-
... More
Erection-200 mm width X 75 mm depth X 1.6 mm thickness
150
-
-
... More
Supply-300 mm width X 75 mm depth X 1.6 mm thickness
100
-
-
... More
Erection-300 mm width X 75 mm depth X 1.6 mm thickness
100
-
-
... More
Supply-450 mm width X 75 mm depth X 1.6 mm thickness
50
-
-
... More
Erection-450 mm width X 75 mm depth X 1.6 mm thickness
50
-
-
... More
Supply-600 mm width X 75 mm depth X 1.6 mm thickness
50
-
-
... More
Erection-600 mm width X 75 mm depth X 1.6 mm thickness
50
-
-
... More
SITC of 25 mm thick Class "O" Closed cell nitrile rubber insulation for UNDER DECK THERMAL INSULATION for exposed roof. Slab to cleaned and adhesive shall be applied on the roof and on the insulatilon . Insulation shall be stuck to roof firmly. Flat clamps, L clamps, etc. sall be used at the edges corners, etc. to ensure the insulation firmly stuck to roof. GI Clampings shall be fixed to the room with screws. Necessary clamping shall be used neaer the conduits , other services , etc. to ensure the insulation is firmly fixed to the slab. ( EPS , 18 Kg density TF quality).
-
-
-
... More
Supply
200
-
-
... More
Erection
200
-
-
... More
Supplying, installation, testing and commissioning of floor mounted cubical type Outdoor ( All weather proof) - Application electrical power supply panel - with double door system - IP 65 protection- (On suitable foundation to withstand a wind speed of 160 KMPH -) suitable for 415V, 3 Phase, 4 Wire, 50 Hz AC supply system fabricated in compartmentalized design CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process, powder coating in approved shade, having 500Amps capacity 4 strip bus bars of high conductivity, entire panel shall have a common GI earth bar of size 25 mm x 5 mm. Digital type Multifunction meter for measuring Frequency, Voltage, Current and Power Factor, KW, KWH with CTs. Phase indication LED lamps with 2 Amp SPMCBs 10 KA Breaking capacities, as per standard practice, as required. -1 Set. Incomer 500 Amps four pole, 35KA breaking capacity (Ics) MCCB, thermal magnetic release type with earth fault protection, rotary handle - 1 Nos. OUT GOINGs : - 63 Amps four pole, 25KA breaking capacity (Ics) MCCB, thermal magnetic release type with rotary handle - 08 Nos. NOTE: MCC Panel shall be installed near to ODU location ( i.e. Terrace of bldg)
-
-
-
... More
Supply - MCC Panel
1
-
-
... More
Erection - MCC Panel
1
-
-
... More
EARTHING SYSTEM:Supply & laying of GI Earth strip for connecting Electrical panels , ODU's atc. as per site requirement
-
-
-
... More
Supply - 25 mm x 3 mm thick ( one inch flat)
190
-
-
... More
Erection - 25 mm x 3 mm thick ( one inch flat)
190
-
-
... More
Supply - Single core - Green PVC Insulated 2.5 Sq.mm wire
140
-
-
... More
Erection - Single core - Green PVC Insulated 2.5 Sq.mm wire
140
-
-
... More
STRUCTURAL FABRICATED STEEL WORK: Supply, Fabrication , Cutting, Welding , Erection at site and painting of M. S. Angle structural steel work for required truss, AC /Supporting structurer/etc. & as per site requirements, etc. based on the approved drawings. The work should be carried out as per good manufacturing and installation practices in concurrence with approved drawings. The structural steel materials should confirm to IS : 2062 (latest version) as per drawings. All welding electrodes to confirm to relevant IS codes. Fabrication and erection of the structural steel works shall be as per IS: 800 and welding work as per IS:816 and IS: 822. Finally all steel work to be painted with one coat of zinc chromate primer and two coats of synthetic enamel paint.
-
-
-
... More
Supply
1500
-
-
... More
Erection
1500
-
-
... More
Charging of suitable eco-friedly Refrigerant / as per OEM recommended refrigerant in VRF/VRV Systems
-
-
-
... More
Supply
150
-
-
... More
Comprehensive AMC of Complete VRF/VRV System of New Computer Bldg.
Comprehensive maintenance of ( Routine & Preventive ) and breakdwon of high side and lowe side of the VRF/VRV -144 HP Capacity Air Conditioning system comprising all the machinery - IDU's ; ODU's , remotes, electrical MCC panel, equipments including spares , consumables , etc. as given in additional terms and conditions complete as required (after One year defect liability period / after warrantee period .)
-
-
-
... More
First Year / HP
144
-
-
... More
Second Year /HP
144
-
-
... More
Removal of existing GI ducting & closing the openings with suitable GI duct with necessary fittings, etc. and safe disposal at Stores with necessary transporatation.
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements