Municipality Tender

Drilling of Bore well;supply of 10 Sqmm 4 core XLPE insulated, 1100V grade armoured amuminium cable as per specification confirming to IS 7098 (PART-I) (Make: Torrent/Universal/Polycab/Havells/Unicab/Gloster/KEI/Finolex/Paragon)

Drilling of Bore well;Manufacture, Supply and fixing of 32mm dia GI couplings of the fallowing sizes including cost and conveyance of material and all labour charges etc,. Complete.

Drilling of Bore well;Supply and delivery of 32mm dia GI bends heavy duty " C" class threaded at both ends at site of work for pump installation including cost and conveyance of all materials, and etc, complete.

Drilling of Bore well;Supply and Delivery of 32" dia long GI NIPPLE including cost and conveyance, all labour charges etc., complete.

Drilling of Bore well;ELEC-5.13.6 : Supply and delivery of MS Clamp set 50mm dia, 450mm length,12mm thick plate, 75mm wide with 6Nos of 16mm dia Bolts & Nuts at site of work for pump installation including cost and conveyance of all materials, etc, complete.

Drilling of Bore well;ELEC-1.6.3 : Supply abd delivery of PVC insulated and PV sheated flexible 3 core 2.50 sqmm flat type submersible cables suitable for submersible pumpsets conductors composed of ennealed high conductivity copper wire, conforming to IS 694 with its revisions and ammendments from time to time and delivery at site of installation of pumpset including freight and transit. Makes : Finolex / RR Kabel / Havells / KEI /L&T

Drilling of Bore well;Manufacture, supply, & delivery of Polyethylene pipes (PE-100 Grade) for water supply conforming to IS 4984-2016 including transportation to any where in T.G, but excluding GST and specials etc., complete.(12.5 kg pipe) 40mm dia suction pipe

Drilling of Bore well;ELEC-5.10.1 : Supply and Transportation of control panel for Single phase submersible motors up to 3 HP @ 220V 50Hz operating range between 80 to 240V Including supply and fixing of Direct - on - Line LTLK / SIEMENS / CROMPTON make, Volt meter and 0-30A Ammeter, Ammeter with starting and running capacitors assembled with ISI mark contactors and fitted with Legrand make ISI mark MCB etc., complete.

Drilling of Bore well;Supply and delivery,of submersible pumpsets suitable to 110mm dia Borewell coupled with motors Single phase 2880 RPM 340V(-15%+10% range-290 to 375 Volts) / 3 Phase 2880 RPM 400V(-15%+10% range-340 to 440 Volts) of reputed make with minimum overall efficiency of 40% at the duty point with Radial / mixed flow with a trail run of One week.The pumpset should confirm to IS 8034/2002 & 9283/1995 with up to date amendments with ISI mark and a guarantee period of 18 months from the date of installation. The rates are inclusive of , transportation, installation, errection of pumpsets including accessories etc, complete. Makes:Texmo / CRI / KSB / Aryan Varsha / Lubi - 2HP 25 stage

Drilling of Bore well;ELEC-5.13.6 e : Supply & fixing of 150mm Dia Bore Cover including cost and conveyance,all labour charges ., complete

Drilling of Bore well;Supplying and fixing of 160mm dia PVC Casing pipe of 6kg/cm2 including cost and conveyance, all labour charges

Drilling of Bore well;Drilling of Bore well by down the hole hammer drilling to a finished dia of 6 1/2 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges and but excluding the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time.