Municipality Tender

Store;BLD-CSTN-2-14 Supply and palcing of the M - 25 Design Mix concrete corresponding to IS 456 using WEIGH BATECHER / MIXER with 20 MM size graded machine crushed hard granite metal (coarse aggregate ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (Sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing , laying concrete, curing etc., complete but excluding scost of steel and its fabricaton charges for finished item of work (APSS No. 402) with minimum cement content as per IS code - Columns

Store;BLD-CSTN-2-14 Supply and palcing of the M - 25 Design Mix concrete corresponding to IS 456 using WEIGH BATECHER / MIXER with 20 MM size graded machine crushed hard granite metal (coarse aggregate ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (Sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing , laying concrete, curing etc., complete but excluding scost of steel and its fabricaton charges for finished item of work (APSS No. 402) with minimum cement content as per IS code - Brace Beams

Store;BLD - CSTN - 6 -18 Masonry work in CM(1:8) prop with Flyash Cement solid blocks of size290x225x140mm for manufacturing of flyash solid blocks using flyash of 80kgs, cement of 15kgs. Gypsum of 5kgs .and stone dust including cost and conveyance of all materials ,labour charges ,seinorage charges ,scaffolding and curing etc.,complete with acompresive streangth not less than 50k/sqm for walls for Superstructure Walls

Store;BLD-CSTN-6-10 Plastering with cm 2 Coats, 12 mm thick, base coat in Cm (1:5) 8mm thick and top coat in Cm(1:5), 4mm thick with dubra Sponze finishing including cost and convience of all men and material labour charges etc., complete finished item of work - Outside

Store;BLD-CSTN-2-19 Supplying,fitting and placingTMT bar reinforcement in foundation complete as per drawings and technical specifications for Bars below 36mm dia including over laps and wastage, where they are not welded.

Store;BLD-CSTN-12-12-(197) Painting in two coats with synthetic best enamal paint of approved quality, colour and shade over a primary coat of white lead to new wood/steel works after the surfaces is throughtly cleaned and scraped, including scaffolding cost of materials and labour charegs etc. complete for finished item of works.

Store;Providing and fixing of Three shutter Sliding Windows made of Galvanized Steel as per IS 513, D quality, galvanized as per IS 277 powder coated with Pure polyester powder and thickness of 0.8 mm for Outer Frame and 0.58 mm thickness for Sliding Shutter Section, with two integrated guide tracks of 12mm width and 24mm deep for provision to slide the Shutter / sash frame and facilitates with a water drain outlet component made of PVC and the shutter frame fitted with 5mm thick plain float glass of reputed make and fixed with EPDM weathering seal resistant accessories and handle made of Aluminium 1 No. per each shutter and including installation of window system at site using anchor fasteners, Silicon sealant applied at the Outer frame corners inclusive of conveyance of all materials accessories, labour charges, and erection at site with complete finished item of work for ii) Centre Shutter Sliding: centre shutter frame made of section of size 20mm x 47mm should be fitted with 5 mm thick plain float glass of reputed make. The supporting guide section of size 15mm x 19mm of 0.58mm thick fixed horizontally at top and bottom of shutter frame and slides along the bottom and top guide tracks made of sections size 24mm x 20mm of 0.58mm thick and 29mm x 20mm of 0.58mm thick and iii) Centre Fly mesh Shutter Sliding: Section for Fly mesh Shutter frame should be of size 20mm x 40mm of 0.58mm thick and fitted with SS mesh (304 Grade). The supporting guide section of size 29mm x 20mm of 0.58mm thick at the bottom and 15mm x 19mm of 0.58mm thick at the top fixed horizontally to the Fly mesh frame and slides along the bottom and top guide tracks made of sections size 20mm x 20mm of 0.58mm and 29mm x 20mm of 0.58mm.

Store;Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of 100*65 MM with encapsulation of 6 MM rigid layer on all external surfaces. The door frame will have a rebate of 32MM/ 37 MM. The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine.The ready/assembled door frame is fixed to wall using Z Hand fast 300 MM long hold fast

Store;Supplying and fixing of 28/30 mm thick Wood Plastic Composite (WPC) Door shutter, comprising of 70% virgin polymer, 15% wood powder (fiber), and the remaining 15% additives, comprising of virgin PVC polymer of K value 58-60 (Suspension grade), Calcium carbonate and natural fibers (wood powder) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum door density of 650 kg/cum, screw withdrawal strength 1800N (Face) & 900N (Edge), Modulus of Elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws all as per direction of Engineer - in- Charge (SS butt hinges and SS screws shall be paid separately)

Store;Supply and delivery of 110 mm dia 3 M Single socket PVC / SWR pipe - 4 Kg / Sqcm includign cost and conveyance of materials etc. complete

Store;Plain / reinforced cement concrete in substructure complete as per drawings and technical specification clauses 802, 804, 806, 807, 1202 and 1204 MORD and 1500, 1700 & 2200 MORTH - including cost and conveyance of all materials to site and labour charges, sales tax etc., complete for finished item of work.