Municipal Corporation Tender

work;Providing independent earthing for important equipement with 100mm die heavy gauge C.I (cast iro) pipe with Flange 2.5m long enclosed in C.C/ Brick massonry chamber of 450m X 450m X400mm with R.C.C slab cover duly providing staggered holes filling with salt and charcoal form the bottom of thepipe giving eath connection from electrode through G.I. strip of 40 X 6mm X200mm length with all accessories and labour chargers complter as per IS specifications 732/1982 (Part II).

work;Supply and fixing of Automatic Street Light Control System based on daywise users settable mode of astronomical timer or digital timer with Optical Micro Sensor, Low voltage / High voltage trip and reset, operating voltage 380 - 480V AC, 50 HZ and shall withstand surge level of 8 KV. The electronic controller with IP 65 protection and suitable SMC / PC enclousure with IP 54 rotection, MCBs of Legrand / Schneider / LK / Siemens / BCH of 10kA C curve and Contactor suitable to control the load 3 KW Three phase load with necessary hardware, Allen key set and clamping arrangements. Makes : Nature switch / Light Mate / Havells (SSR 2024-25 Elec: 3.2.2 A)

work;Supply and fixing of Automatic Street Light Control System based on daywise users settable mode of astronomical timer or digital timer with Optical Micro Sensor, Low voltage / High voltage trip and reset, operating voltage 380 - 480V AC, 50 HZ and shall withstand surge level of 8 KV. The electronic controller with IP 65 protection and suitable SMC / PC enclousure with IP 54 rotection, MCBs of Legrand / Schneider / LK / Siemens / BCH of 10kA C curve and Contactor suitable to control the load 5 KW Three phase load with necessary hardware, Allen key set and clamping arrangements. Makes : Nature switch / Light Mate / Havells (SSR 2024-25 Elec: 3.2.2 B)

work;Supply & fixing of 10 Sqmm 4 Core XLPE insulated, 1100V grade armoured alluminium cable with ISI mark as per specification confirming to IS:7098 (SSR 2024-25 Elec: 4.1.1 (e))

work;Supply of Crane for replacing Equipment i) For 1st Hour Rs.1,300/- as per TS SPDCL SSR Service Code SWR20577. (Ref: as per PM Order Number:930000063422 enclosed)Approved file No.E-189313)

work;Compressor charges for Hardrock cutting for dismantlling of foundation of high mast (as per market rate)

work;Earth work excacvation including all soils for trench, Pole Pit and Earth Pit.

work;Fixing Charges for 110W/190W fittings

work;Dismantling of 110W/190W fittings

work;Erection charges for 12 Mtrs to 14.5 Mtrs long MS Tubular pole including excavation of pit 156Cm X 60Cm X 60Cm, coil earthing, Pole CC 1:3:6 upto ground and 1:2:4 for Couping work, including labour and transportation charges etc., complete

work;Dismantling of 12 Mtrs Pole

work;Foundation and erection charges with special T&P, for 8.00/ 9.00Mtrs / 10Mtrs long Octagonal / Conical pole duly erecting on base plate duly providing 4 Nos foundation bolts with nuts with providing of 0.60Mtrx 0.60Mtrs x1.40 Mtr size M20 cc work vibrated concreting mixing with necessary steel (15kgs) reinforcement as directed by the field engineers during execution including centering, decentering, water curing as required, soil exacavation, back filling, muffing removal and coil earthing including all labour charges and cost and conveyance ofbmaterials etc. complete. (SSR 2024-25, ELEC: 8.11.3)

work;Foundation and erection charges with special T&P, for 7.50 /4 Mtrs long Octagonal / Conical pole duly erecting on base plate duly provided 4 Nos foundation bolts with nuts with providing of 0.45Mtr x0.45Mtrsx1.20 Mtr size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement as directed by the field engineers during execution including centering, decent ring, water curing as required, soil excavation, back filling, muffing removal and coil earthing including all labour charges and cost and conveyance of materials etc. complete.. (SSR 2024-25, ELEC: 8.11.2)

work;Laying charges UG cable

work;Supply of 16 Sqmm 4 Core XLPE insulated, 1100V grade armoured alluminium cable with ISI mark as per specification confirming to IS:7098 (SSR 2024-25 Elec: 4.1.1 (f))

work;Supply fo Neri 8M Height Flood Light Pole - 8M Height Single Arm pole is made in combination of mild steel pipe sections of 140mm dia., 114mm dia. & 89mm dia. Provision made to mount 3No.s of Flood Lights. The pole to be provided with a suitable size steel base plate. This mounting steel base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. After Fabrication, Entire Pole should be shot blasted for the effective adhesion of 3layer coating so as to avoid the corrosion. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. Pole & it's parts are painted in 3 layer coating in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint-in Customized mettalic Grey Colour.Make: Neri/Jaguar/K-Lite

work;Supply of Neri Flood Light, NFL-6-200 195-205W, LED, 3000k, IP 66 - The housing in light weight, made of high strength die cast aluminium using pressure die casting process .Protection screen in tempered glass with high impact resistance.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Black Colour. Precise structure and multi-protection silicon gasket ensures the ingress protection-IP 66. Height ?437mm, Width-392mm & Depth-61,Weight -4Kg. Power LED Module with high efficacy LED's on Printed Circuit Board with metal core plate. CRI > 80, beam angle-120deg. Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Estimated LED Lifetime is 50,000 hours minimum. BIS Certificate with manufacturer name same as brand proposed should be submitted.. Sample should be submitted for approval from concerned engineer-in charge. Make: Neri/Jaguar/K-Lite

work;Supply of Neri Architectural Post Top Pole of 4M Height Triple Arm Pole Made of steel pipe section of 76mm dia with grooves (6 Nos). Decorative Bracket (3nos.) Nashira design with decorated leafs as shown in the diagram with a 3/4" GAS threaded tube with nut and rose in stainless steel for attaching the light fixture and an internal tube for the passage of a power cable made of cast iron in single piece, to get an arm length of 550mm & pleasing aethetics as approved. Decorative Base in Steel - Its design starting with dia 260mm for 170mm height, then tapers to 180mm, followed by a cylindrical section of 165mm dia., 365mm Height. It ends with a Top section consist of a Ring of 205mm dia. and 40mm height followed by a taperinng section with Bottom dia. 175mm, Top dia 105mm and Height of 90mm. Total Height of the Base is 700mm. A Steel base plate of 300mm x 300mm is welded at the bottom of the base. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160mm and then tapering to a dia 99mm.Total height of cast iron flower is 304 mm & weight is 6.3kg. All cast iron parts weight mentioned are with +/- 5% tolerance. Entire pole including the decorative elements shall be made to provide pleasing aesthetics as approved by Architect/ Engineer in-charge. After Fabrication, Entire Pole should be shot blasted for the effective adhesion of 3layer coating so as to avoid the corrosion. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom - the inbuilt box should have a flush door of suitable size. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. Sample should be submitted for approval from Architect/ engineer-in-charge. Make: Neri/Jaguar/K-Lite

work;Supply of Neri Architectural Post Top Lantern Model - Light 804 C, 30W-40W, Power Module LED, 3000k, Upright Upper square frame made in die-cast aluminum using pressure die casting process. Lower frame with four-armed bracket with flange and a hole (diam. 28 mm) for attachment to the support, is made in aluminum. Auxiliary and optical compartment can be accessed by opening the upper frame. Pure polyester powder coating in Customized Metallic Grey Colour. Silicone gasket between the upper and lower frames ensures IP Rating - IP 66. Height ? 586mm, Length - 325mm,Width-325mm,Weight - 5Kg.Power LED Module with Company /brand name printed on PCB with the metal core plate. LED chips of CREE/NICHIA/OSRAM/LUMILED make shall be used. Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours. Safety test report as per IEC 60598/IS 10322 from UL/UL Authorised/Intertek should be submitted. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. BIS Certificate with manufacturer name same as brand proposed should be submitted. Sample should be submitted for approval from concerned engineer-in charge.Make: Neri/Jaguar/K-Lite

work;Supply of Neri Architectural Post Top Pole of 4M Height - 4M height post top Pole Made of steel pipe section of 76mm dia with 6 grooves. Decorative Base in Steel - Its design starting with dia 260mm for 170mm height, then tapers to 180mm, followed by a cylindrical section of 165mm dia., 365mm Height. It ends with a Top section consist of a Ring of 205mm dia. and 40mm height followed by a taperinng section with Bottom dia. 175mm, Top dia 105mm and Height of 90mm. Total Height of the Base is 700mm. A Steel base plate of 300mm x 300mm is welded at the bottom of the base. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160mm and then tapering to a dia 99mm.Total height of cast iron flower is 304 mm & weight is 6.3kg.. Top Ring-(weight- 3kgs.) made of cast iron. All cast iron parts weight mentioned are with +/- 5% tolerance. Entire pole including the decorative elements shall be made to provide pleasing aesthetics as approved by Architect/ Engineer in-charge. After Fabrication, Entire Pole should be shot blasted for the effective adhesion of 3layer coating so as to avoid the corrosion. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom - the inbuilt box should have a flush door of suitable size. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. Sample should be submitted for approval from Architect/ engineer-in-charge. Make: Neri/Jaguar/K-Lite

work;Supply of Neri Architectural Post Top Lantern Model - Light 804 C, 30W-40W, Power Module LED, 3000k, Upright Upper square frame made in die-cast aluminum using pressure die casting process. Lower frame with four-armed bracket with flange and a hole (diam. 28 mm) for attachment to the support, is made in aluminum. Auxiliary and optical compartment can be accessed by opening the upper frame. Pure polyester powder coating in Customized Metallic Grey Colour. Silicone gasket between the upper and lower frames ensures IP Rating - IP 66. Height ? 586mm, Length - 325mm,Width-325mm,Weight - 5Kg. Power LED Module with Company /brand name printed on PCB with the metal core plate. LED chips of CREE/NICHIA/OSRAM/LUMILED make shall be used. Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours. Safety test report as per IEC 60598/IS 10322 from UL/UL Authorised/Intertek should be submitted. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. BIS Certificate with manufacturer name same as brand proposed should be submitted. Sample should be submitted for approval from concerned engineer-in charge. Make: Neri/Jaguar/K-Lite