Mission Bhagiratha Department Tender

2BHK Siddaipally;Supply and Transportation of control panel for three phase submersible motors above 5 HP up to 7.5 HP @ 415V 50Hz operating fitted with supply and fixing of Direct - on - Line LTLK /BCH/ SIEMENS / CROMPTON make, 0-500V Volt meter and 0-30A Ammeter, Indication lamps, selector switches, CTS, 32A TP MCB, Single phase preventor, suitable contactor to with stand low voltage pick up and high voltage resistant, with ISI marked capacitors assembled with ISI mark contactors and fitted with Legrand make ISI mark MCB etc., complete

2BHK Siddaipally;Supply and Run of No.8 SWG G.I wire including cost of all accessories like U nails etc including connections and labour charges etc. complete.

2BHK Siddaipally;Providing independent earthing for Important equipment with 100mm dia Heavy gauge C.I ( Cast iron ) pipe with Flange 2.5m long enclosed in C.C/ brick massonry chamber of 450m x 450m x400mm with R.C.C. Slab cover duly providing staggered holes filling with salt and charcoal from the bottom of the pipe giving earth connection from electrode through flange with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II)

2BHK Siddaipally;Supply and run of 3 Core 4.0 Sqmm Flat Copper cable as per IS 694:1990 for Submersible Motors. including providing end terimations with glands. lugs , crimping job etc complete for finished item of work.. Makes : Finolex / RR Kabel / Havells /Nakoda.

2BHK Siddaipally;Supply and run of 6 Sqmm 4core UG cable XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I)in exsting trench/wall including providing end terimations with glands. lugs , crimping job etc complete for finished item of work

2BHK Siddaipally;Supply, delivery ,transporation, errection, testing and commisioning of 5 HP open well submersible motor pump set of Makes: Texmo / CRI / KSB / Aryan Varsha / Lubi with water resistant dynamically balanced impeller with stainless steel sleeves pump coupling and pivot with squirrel cage inductor motor of 3phase 415V 50HZ AC supply heavy copper windings with with water proof insulation and high pressure strength not to be efected by chemicals in water with suitable bronze bearings errected with h-type clamps odutable size and strength including cost of all materilas, transportation and all labour chrages as per the directions of the Engineer-in-charge with discharge 199LPM and head 41.85Mts.

2BHK Siddaipally;Supply and delivery laying true to alignment jointing with flanges of PN 1.6 rated DI D/F Gate valves(soft seated) resilient seated soft seating Gate valves(Sluice valves) of PN 1.6 grade with body bonnet of Ductile cast iron of grade GGG40/SG-400/15 or GGG-50/SG-500/7 or equivalent grade as per IS.3896-Part2-1985 and sub sequent revisions, wedge fully rubber lined with EPDM food grade quality and seals of NBR and the valves should be vaccum tight and 100% leak proof with face to face dimensions as per BS5163-89/IS14846-2000/DIN 3202 F 4, valves should be with Electrostatic powder coating both inside and outside pocket less body passage, drilled as per IS:1538 to suit the pressure class of pipe including supply delivery laying and jointing of S/F tapered tail pieces of 5 and 15 degrees on either ends to suit the main pipe line and valve including cost of joint materials such as rubber gaskets,bolts and nuts and labour charges with construction of RCC valve chambers as per requirement with RCC slab and RCC man hole cover with locking arrangement etc.with by pass and gear arrangement for size more than 450mm complete for finished item of work but excluding CED upto 600mm dia. 100 mm dia Sluice valve on 110 mm dia line

2BHK Siddaipally;Supply and delivery laying true to alignment jointing with flanges of PN 1.6 rated DI D/F Gate valves(soft seated) resilient seated soft seating Gate valves(Sluice valves) of PN 1.6 grade with body bonnet of Ductile cast iron of grade GGG40/SG-400/15 or GGG-50/SG-500/7 or equivalent grade as per IS.3896-Part2-1985 and sub sequent revisions, wedge fully rubber lined with EPDM food grade quality and seals of NBR and the valves should be vaccum tight and 100% leak proof with face to face dimensions as per BS5163-89/IS14846-2000/DIN 3202 F 4, valves should be with Electrostatic powder coating both inside and outside pocket less body passage, drilled as per IS:1538 to suit the pressure class of pipe including supply delivery laying and jointing of S/F tapered tail pieces of 5 and 15 degrees on either ends to suit the main pipe line and valve including cost of joint materials such as rubber gaskets,bolts and nuts and labour charges with construction of RCC valve chambers as per requirement with RCC slab and RCC man hole cover with locking arrangement etc.with by pass and gear arrangement for size more than 450mm complete for finished item of work but excluding CED upto 600mm dia. 80 mm dia Sluice valve on 90 mm dia line

2BHK Siddaipally;Supply and delivery laying true to alignment jointing with flanges of PN 1.6 rated DI D/F Gate valves(soft seated) resilient seated soft seating Gate valves(Sluice valves) of PN 1.6 grade with body bonnet of Ductile cast iron of grade GGG40/SG-400/15 or GGG-50/SG-500/7 or equivalent grade as per IS.3896-Part2-1985 and sub sequent revisions, wedge fully rubber lined with EPDM food grade quality and seals of NBR and the valves should be vaccum tight and 100% leak proof with face to face dimensions as per BS5163-89/IS14846-2000/DIN 3202 F 4, valves should be with Electrostatic powder coating both inside and outside pocket less body passage, drilled as per IS:1538 to suit the pressure class of pipe including supply delivery laying and jointing of S/F tapered tail pieces of 5 and 15 degrees on either ends to suit the main pipe line and valve including cost of joint materials such as rubber gaskets,bolts and nuts and labour charges with construction of RCC valve chambers as per requirement with RCC slab and RCC man hole cover with locking arrangement etc.with by pass and gear arrangement for size more than 450mm complete for finished item of work but excluding CED upto 600mm dia. 80 mm dia Sluice valve on 75 mm dia line

2BHK Siddaipally;S & F 25 mm nominal size copper body float valve with PVC ball Indian make ISI mark

2BHK Siddaipally;S & F Bronze Ball valve with SS Ball and SS Spindle as per IS- Class - I, Indian make heavy type - 25 mm NB Size

2BHK Siddaipally;PP Clamp Saddle shall comply with AS/NZS 4793 or relevant international standards-Mechanical tapping saddles for water works purposes and designed for use with PVC/PE pipe as per IS 4985/ IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP Saddles shall be blue with moulded SS female threaded outlets. Seal shall be thermoplastic elastomer rubber suitable for drinking water and SS nut-bolt-washer. Maximum working pressure rating of 10 bar. 75X1"

2BHK Siddaipally;PP Clamp Saddle shall comply with AS/NZS 4793 or relevant international standards-Mechanical tapping saddles for water works purposes and designed for use with PVC/PE pipe as per IS 4985/ IS 4984 respectively. These saddles should be contoured to fit around the pipe. PP Saddles shall be blue with moulded SS female threaded outlets. Seal shall be thermoplastic elastomer rubber suitable for drinking water and SS nut-bolt-washer. Maximum working pressure rating of 10 bar. 63X1"

2BHK Siddaipally;Laying, jointing of UPVC/HDPE pipes as per BIS No.7634 part-III

2BHK Siddaipally;Earthwork excavation for pipe line

2BHK Siddaipally;Manufacture, Supply and Delivery of Unplasticised PVCs Pipes for potable water supplies conforming to IS : 4985/2000 (3rd revision) with bell ends (Socket) as per specification in light Grey/Natural Ivory Grey/ Any other Color (except White) inclusive of transportation to the sub-divisionalstores anywhere in TG excluding taxes.

2BHK Siddaipally;Construction of pipelines for water supply with HDPE pipes as per IS 4985:1995 with its amendments and revisions thereon including supply of pipes necessary specials such as bends, Tees, as per site requirements, lowering, laying and jointing of pipes (with Butt fusion welding) true to alignment and gradient, excavation of pipe line trench (Earth work excavation in all soils, up to SDR using machine rate for 2/3rd and manual rate for 1/3rd of quantity) of pipe lines in all soils except hord rock requiring Blasting and refilling trenches with excavated earth (other than rocky soils, boulders and BC soils) with watering and tamping . removing surplus earth from site of work, and filling pipe line with water and testing to the required pressure etc., Complete., The rates are inclusive of cost and conveyance of all materials and labour charges and all incidental and operational charges for finished item of pipe line work, but excluding GST and other taxes. 110 MM 6 KG/CM2

2BHK Siddaipally;Construction of pipelines for water supply with HDPE pipes as per IS 4985:1995 with its amendments and revisions thereon including supply of pipes necessary specials such as bends, Tees, as per site requirements, lowering, laying and jointing of pipes (with Butt fusion welding) true to alignment and gradient, excavation of pipe line trench (Earth work excavation in all soils, up to SDR using machine rate for 2/3rd and manual rate for 1/3rd of quantity) of pipe lines in all soils except hord rock requiring Blasting and refilling trenches with excavated earth (other than rocky soils, boulders and BC soils) with watering and tamping . removing surplus earth from site of work, and filling pipe line with water and testing to the required pressure etc., Complete., The rates are inclusive of cost and conveyance of all materials and labour charges and all incidental and operational charges for finished item of pipe line work, but excluding GST and other taxes. 90 MM 6 KG/CM2

2BHK Siddaipally;Construction of pipelines for water supply with HDPE pipes as per IS 4985:1995 with its amendments and revisions thereon including supply of pipes necessary specials such as bends, Tees, as per site requirements, lowering, laying and jointing of pipes (with Butt fusion welding) true to alignment and gradient, excavation of pipe line trench (Earth work excavation in all soils, up to SDR using machine rate for 2/3rd and manual rate for 1/3rd of quantity) of pipe lines in all soils except hord rock requiring Blasting and refilling trenches with excavated earth (other than rocky soils, boulders and BC soils) with watering and tamping . removing surplus earth from site of work, and filling pipe line with water and testing to the required pressure etc., Complete., The rates are inclusive of cost and conveyance of all materials and labour charges and all incidental and operational charges for finished item of pipe line work, but excluding GST and other taxes. 75 MM 6 KG/CM2

2BHK Siddaipally;Construction of pipelines for water supply with HDPE pipes as per IS 4985:1995 with its amendments and revisions thereon including supply of pipes necessary specials such as bends, Tees, as per site requirements, lowering, laying and jointing of pipes (with Butt fusion welding) true to alignment and gradient, excavation of pipe line trench (Earth work excavation in all soils, up to SDR using machine rate for 2/3rd and manual rate for 1/3rd of quantity) of pipe lines in all soils except hord rock requiring Blasting and refilling trenches with excavated earth (other than rocky soils, boulders and BC soils) with watering and tamping . removing surplus earth from site of work, and filling pipe line with water and testing to the required pressure etc., Complete., The rates are inclusive of cost and conveyance of all materials and labour charges and all incidental and operational charges for finished item of pipe line work, but excluding GST and other taxes. 63 MM 6 KG/CM2