Irrigation And CAD Department Tender

Dhanalaxmi LIS;Manufacturingand supply of control panel board. The panel board should be metal clad, dust and vermin proof, floor mounted industrial type,indore type for,controlling 2Nos. 40 HP SPDP Squirrel case induction motors. The panel board with accessories should internally wired neccessary earthing terminal shall be provided. the electrical system shall comply as per IE rules and relevant ISS. The thickness of sheets to be used for fabrication of panelboard should be 16guage. the cable boxes wherever necessary with adequate cabling space for termination of cable is to be provided, Complete for finished item of work as directed by the Engineer-in-Charge. "Note:- Any alterations suggested by electrical inspector during inspection are to be attended by the tenderer / contractor without claiming extra payment" The panel boards should consists of the following accessories Bus bars :- Electroclytic quality aluminium bus bars. Size of bus bars:- 17mm x 6 mm for phase-1no. 9 mmx6 mm for neutral -1 No. MCCB:a) Quantity : 1 no.b) Capacity : 200 Amps.c)L&T/ Kirloskar/EE I/EASUN T.P Switches fuse units for controlling motors.a) Quantity : 2 nos.b) Capacity : 100Amps. c)Rating of HRC fuse : 100 Amps.d) Voltage : 440 voltse) Make : L&T/ EE / GEC / EASUN / SIEMENS / STANDARD/HAVELLS" "T.P Switches fuse units for controlling capacitors.a) Quantity : 2 nos.b) Capacity : 1) 63 Amps.c) Rating of HRC fuse : 11.5 to 14.95Amps.d) Voltage : 415 volts A.C e) Make: L&T/ EE/GEC/ EASUN / SIEMENS /STANDARD/HAVELLS" "T.P Switch unit for vaccum pump. a) Quantity : 1 no.b) Capacity : 1) 12.50 Amps.c) Rating of HRC fuse : 1.5 Amps. d) Voltage : 440 volts e) Make:L&T/EE/GEC/EASUN/SIEMENS /STANDARD/HAVELLS" "TPN 415 volts panel mounted type switch. Fuse unit with rewirable fuses of 12.5 Amps capacity for lighting purpose - 1no. Starters for motors: a) Quantity : 2 nos.b) Capacity : 40 HP - 2 Nos.c) Coil voltage: 380 Volts with protective devices d) Mode of starting: Star Delta e) Type : Fully automatic /Air break / Oil immersed f) Make: LT LK/ SIEMENS / Cutler Hammer/Jyothi/ Kilbur/ GEC "Starter for vaccum pump: a) Quantity : 1 no.b) Coil Voltage : 380 Volts c) Type: DOL Air Break d) Capacity : 5.0 HP e) Make: LT LK/SIEMENS/CUTLER HAMMER Contactor rating : 0.75 A to 1.5 A "Thermister Relay unit:Thermister setting : As per Manufacturers design a)Application : to be connected to the Thermister embedded in phase winding of each motor b) Quantity: 2 nos. c) Makes:NGEF /Siemens / GEC/LT-LK/ Tempsen/ Kilburn d) Relay Range : As per Manufacturers design" "Capacitors :a) Type:L.T. Phase shunt capacitors b) Rating in KVAR: 10 KVARc) Quantity : 2 nos.d) Make: L & T / New Bijili / GEC / Crompton" " Voltmeter with selector switch :a) Quantity :1 set b) Rating. : 0-500 V Type: Panel mounted flush type preferably Somare type.c) Make : Electro / L & T / Havells / MBCC /NIPPON " Ammeter with selector switch :a) Rating : i) 0-60Amps(Suppressed)ii) 60 to 120 Amps (Enlarged)b) Quantity :2 sets C.T. operated c) Type : Panel mounted Flush type preferably Somare type CT operated to be suppressed by four times from 50% range to the maximum range specified d) Make : AE/Analog/ L & T / Havells / NICCO /NIPPON""Hours Meters: 2 nos. a) Type:Electric/Electronic Hour meter b) Operating rang : 150 volts AC phase to neutral c) Time recording : 5 digit magnetic counter d) Application : for recording the no. of hours the pump worked e) Make : Electromod/KAYEES""Indicating lamps: R-Y-B a) Quantity : 2 sets of RYB for phase indication of incoming supply and out going supply of individual motors"

Dhanalaxmi LIS;HOIST BRIDGES ,HOISTING EQUIPMENT AND CRANES,Etc, Surface cleaning of metal surfaces by chemical cleaners and then by hand and power tool cleaners and removing dust. After cleaning,applying primary coat with two coats of Zinc chromite red oxide primer , followed by finishing coats 3 coats with synthetic enamel paint with material, labour,and all accessories with all leads and lifts where surface cleaning by sand blasting is not feasible and based on specific recommendations of designers, it is to adopt surface preperation done manually by hand and power tool after cleaning by chemical treatment to remove grease, rust, scaling etc., and to form phasphate coating to prevent further rusting, before applying primer painting, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply and transportation of 90 W +/-10% (>=9000 Lumens) LED Flood light Luminaire made of pressure die cast aluminum housing with powder coated, having toughened glass cover, IP 66 (Silicon gasket ensures Optical & Electrical compartments are IP 66 )protected, wide operating voltage range, P.F > 0.90, System having efficacy >100lumens/watt, with Ingress protection IP66, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desired by the department and as per IS, CRI>80, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc complete with BIS certification with 5 years warranty. The contractor must furnish the manufacturer warranty letter, LM 79 and LM 80 certificates.LUMINAIRE MAKE : PHILIPS / OSRAM/GE Venture/CROMPTON/ BAJAJ/Wipro/ Jaquar /Eveready / Halonix / Keselec/HAVELLS /POLYCAB/SURYA/SYSKA/ Capart / FortuneArrt / FIEM / Arraystorm / GM / Goldmedal /Panasonic. LED MAKE : PHILIPS LUMILEDS/ CREE/NICHIA /OSRAM/SAMSUNG/LG LEDs, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply of G.I Bolts / Nuts and Washers, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply of Diesel, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply of Grease, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply of Grease gun 1kg Capacity, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply of 16 mm/12 mm Gland Packing Rope, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Supply of Cotton Waste, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Fabrication supply and fixing of MS pipe and specials including cost of MS sheet,cutting, bending, welding, transportation,fixing in position cost of flanges bolts and nuts ,rubber packing ,primary paint in red oxide ,black paint in two coats etc Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Complete dismantling of 250 mm dia Sluice valve overhauling ,replacement of wornoutnparts like shutter shaft, gun metal buses facing of shutters providing new bolts and nuts rubber packing assembling of valve including cost of material and labour charges trail run at site and all other incidental charges etc, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Complete dismantling of 250 mm dia Non-return valve overhauling ,replacement of wornoutnparts like shutter shaft, gun metal buses facing of shutters providing new bolts and nuts rubber packing assembling of valve including cost of material and labour , Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Overhauling & Servicing to 5 HP Crompton Greaves make Vaccum pump set, including replacement of pump bearings-2 nos (6306), pump shaft gun metal bushes, pump glands, packing, other defective items and assembling of pump erection on base plate, testing, alignment of motor-pump set, trail run at site and all other incidental charges etc, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Overhauling & Servicing to 40 HP Mather+Platt make Pump with discharge 0f 385.3 cusecs,pumping head of 22.8 mtrs, including replacement of pump bearings-2 nos , pump shaft gun metal bushes, pump glands, packing, other defective items and assembling of pump erection on base plate, testing, alignment of motor-pump set, trail run at site and all other incidental charges etc, Complete for finished item of work as directed by the Engineer-in-Charge.

Dhanalaxmi LIS;Dismantling of burnt 40 HP squirrel cage induction motor and rewinding to stator with new HTP make super enamled copper wire, providing new insulation materials, varnishing, heating up to obtaining of required IR values, hot air blowing, checking up of bearings, bearing settings, assembling the motor, erection on base plate correct alignment of pump and motor, trail run at site including cost of all materials, labour charges, transportation charges of motor from scheme to work shop and work shop to scheme after rewinding and all other incidental charges etc, Complete for finished item of work as directed by the Engineer-in-Charge.