Irrigation And CAD Department Tender
For getting the details of etenders, if you are looking for information about them from the cumbersome government websites but are tired of doing so, Bidassist comes up with a one stop solution. It collates every Eproc telangana tender on Bidassist. One can approach it for the bidding process, registration process, etc., are explained below.
Costs
EMD
₹ 37,598Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
572718Tender No
34/2024-25, Dated:27-01-2025Tender Authority
Irrigation And CAD Department ViewPurchaser Address
-Website
http://https://irrigation.telangana.gov.in/icad/home
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
boq;Removing of Gate & Hoist of Infall Regulator and Refixing of Hoist in place with Base plate & anchor rods arrangement etc., complete with all leads and all lifts, as directed by the Engineer in Charge.
2
66934
133870
... More
boq;Supply of Chemical for Degreasing for cleaning of screw rod.
20
193
3862
... More
boq;GAW-4-2:Surface cleaning of metal surfaces by chemical cleaners and then by hand and power tool cleaners and removing dust. After cleaning,applying primary coat with two coats of Zinc chromite red oxide primer ,followed by finishing coats 3 coats with synthetic enamel paint with material, labour,and all accessories with all leads and lifts where surface cleaning by sand blasting is not feasible and based on specific recommendations of designers, it is to adopt surface preperation done manually by hand and power tool after cleaning by chemical treatment to remove grease, rust, scaling etc., and to form phasphate coating to prevent further rusting, before applying primer painting.
187.14
572
107194
... More
boq;GAW-4-1: Surface cleaning of metal surfaces by chemical cleaners and then by hand and power tool cleaners and Removing dust. After cleaning,applying primary coat with one coat of Protective Mastic to athickness of 70+5 microns ,followed by finishing coats 2 coats with Solventless Coal tar epoxy each coat with a DFT of 70+5 microns ,followed by finishing coats 2 coats with Solventless Coal tar epoxy each coat with a DFT of material, labour and all accessories with all leads and lifts
203.92
724
147801
... More
boq;GAW-2-6:Design, fabrication, supply, erection, testing and commissioning of fixed wheel type verticallift service gate consisting of skin plate, vertical and horizontal girders, wheels, stiffeners, liftingbrackets, guide rollers, ballast blocks, teflon claded rubber seals etc., with all accessories forriver sluice / canal sluice vent including cost of all materials, machinery, labour,welding ,aligning finishing seal fixing etc.with allleads and lifts, complete as per specifications and approved drawings
6.62
190804
1263125
... More
boq;Supply and application of grease.
80
340
27264
... More
boq;Supply & Fixing of Star Delta Starter 415V, Three phase, 50Hz. With SS enclouser comprising of contactor with bi-metalic relay with necessary push buttons, etc., complete suitable from Makes: Siemens / Crompton / L&T / BCH.
2
11247
22496
... More
boq;Supply and fixing of Electric motor 5 hp(Double Shaft)
2
40901
81803
... More
boq;Fabrication and erection of 14SWG CRCA (2mm)sheet steel enclosure for power control cubicle panel / boxes etc., including cutting, bending drilling, welding and reveting etc., complete with cleaning with 7 tank process and painting with powder coating including cost and conveyance of all materials and labour charges.
1.5
7027
10541
... More
boq;Supply and fixing of 6-32A FP MCB 10KA, C/D Curve ISI Mark.
3
2238
6715
... More
boq;Supply and fixing of 100 A 415V Porcelain Rewirable Fuse Units.
3
636
1909
... More
boq;Supply and fixing of 20 mm dia Medium grade PVC Bends.
21
9
191
... More
boq;Supply and fixing of ISI 20 mm outer dia heavy grade, FRLS with IS:9537 part 3 rigid PVC pipe.
93
39
3701
... More
boq;Supply and fixing of 4 Sqmm FRLS / HFFR PVC insulated 1100V grade as per IS:694/1990 specification for Copper cable.
93
44
4176
... More
boq;Supply and fixing of 6 Sqmm 4core PVC / XLPE Insulated, Flexible Armouring Flexible Copper cable as per IS 7098 / Part-I / 1988 including all transportation charges etc complete.
120
454
54540
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%